You can use the NanoVNA-App or NanoVNA-saver.
|
Re: NanoVNA 4 version 1.0.? Only save at 800Hz
On Stop frequency input you use x1 (input as Hz, not in MHz), so input result 7.3Hz, NanoVNA not allow set this value and set minimum 800Hz
Start value less then 800Hz, so and Start value also set to 800Hz
Start value = Stop value, so NanoVNA switch to CW mode
PS use correct input
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
Hi , some time ago , I solved the proble forcing the installation of the ST driver .
Go to location of you have installed the DfuseDemo programa like this on my PC
C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.6\Bin\Driver\Win10
dpinst_amd64.exe dpinst_x86exe
execute dpinst_amd64.exe if the system is 64 bit
execute dpinst_x86exe if the system is 32 bit
of course as administrator of the system :
Best regards
Maurizio IZ1MDJ
|
That sounds great. Should I put the short cable on for calibration since it will be on for all testing that I have planned?Sent from my Galaxy Tab? S2
toggle quoted message
Show quoted text
-------- Original message --------From: "John Gord via groups.io" <johngord@...> Date: 6/18/22 12:25 AM (GMT-06:00) To: [email protected] Subject: Re: [nanovna-users] Nanovna H4 #nanovna-h4 Mike,You can just leave the connector empty instead of using the "open" standard.? There is very little difference at 1500MHz and below.? (This assumes you are using the normally supplied standards which are SMA male.)--John GordOn Fri, Jun 17, 2022 at 09:43 PM, Mike McKinney wrote:>> YeeHaw! I finally got that rascal updated and seems to be working right. Now> just have to wait for the open calibration cap to get here to calibrate and> test some antennas and coax.Sent from my Galaxy Tab? S2> -------- Original message --------From: Stan Dye <standye@...> Date:> 6/17/22? 10:47 PM? (GMT-06:00) To: [email protected] Subject: Re:> [nanovna-users] Nanovna H4 #nanovna-h4 The likely cause of your current issue> is that when you upgrade from asubstantially earlier version of firmware,?> you need to "clear config", andthen power-cycle the nano.? Thus clears the> config variables that may beincompatible with the new firmware.? I think the> "clear config" command isunder the config/expert settings menu in that> firmware.There is a newer version of firmware,? which has not yet been added> to thefiles section of this group. It is at DiSlord's> github: down the page and> click.on the NanoVNA.H4.v1.2.00.dfu file todownload it.? It will also need> the clear configfollowed by re-doing thetouchscreen cal, etc.On Fri, Jun 17,> 2022, 7:52 PM Mike McKinney <theranger53@...> wrote:> Well, I updated> the firmware to the latest version I could find, and that> was a joke. This> thing is F;;;ed now. Can turn it on but I can¡¯t calibrate> the touch and> save it. I touch in the center of the screen and get the> start screen for> setting the Frequency. Can¡¯t open the menu with touch only> with the button> on top. Version 1.0.64 was the newest I could find. If> there is a newer one> could you point me to it. This is a DiSlord version> that I found through the> Absolute beginner PDF.>> Sent from Mail (> ) for> Windows>> *From:* HA3HZ> ( gyula@... )> *Sent:* Friday, June 17, 2022 3:12 AM> *To:*> [email protected]> *Subject:* Re: [nanovna-users] Nanovna H4> #nanovna-h4>> Mike,>> The error message means, as Hugen wrote, that you need> to update the> NanoVNA firmware because the software you were using did not> recognize the> command. So the firmware has not been updated for you, but the> software is> waiting for new commands.>> Updating the firmware will probably> resolve your issue.>> -->> Gyula HA3HZ ( )>>> >>>>
|
Mike,
You can just leave the connector empty instead of using the "open" standard. There is very little difference at 1500MHz and below. (This assumes you are using the normally supplied standards which are SMA male.)
--John Gord
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 09:43 PM, Mike McKinney wrote:
YeeHaw! I finally got that rascal updated and seems to be working right. Now
just have to wait for the open calibration cap to get here to calibrate and
test some antennas and coax.Sent from my Galaxy Tab? S2
-------- Original message --------From: Stan Dye <standye@...> Date:
6/17/22 10:47 PM (GMT-06:00) To: [email protected] Subject: Re:
[nanovna-users] Nanovna H4 #nanovna-h4 The likely cause of your current issue
is that when you upgrade from asubstantially earlier version of firmware,?
you need to "clear config", andthen power-cycle the nano.? Thus clears the
config variables that may beincompatible with the new firmware.? I think the
"clear config" command isunder the config/expert settings menu in that
firmware.There is a newer version of firmware,? which has not yet been added
to thefiles section of this group. It is at DiSlord's
github: down the page and
click.on the NanoVNA.H4.v1.2.00.dfu file todownload it.? It will also need
the clear configfollowed by re-doing thetouchscreen cal, etc.On Fri, Jun 17,
2022, 7:52 PM Mike McKinney <theranger53@...> wrote:> Well, I updated
the firmware to the latest version I could find, and that> was a joke. This
thing is F;;;ed now. Can turn it on but I can¡¯t calibrate> the touch and
save it. I touch in the center of the screen and get the> start screen for
setting the Frequency. Can¡¯t open the menu with touch only> with the button
on top. Version 1.0.64 was the newest I could find. If> there is a newer one
could you point me to it. This is a DiSlord version> that I found through the
Absolute beginner PDF.>> Sent from Mail (
) for> Windows>> *From:* HA3HZ
( gyula@... )> *Sent:* Friday, June 17, 2022 3:12 AM> *To:*
[email protected]> *Subject:* Re: [nanovna-users] Nanovna H4
#nanovna-h4>> Mike,>> The error message means, as Hugen wrote, that you need
to update the> NanoVNA firmware because the software you were using did not
recognize the> command. So the firmware has not been updated for you, but the
software is> waiting for new commands.>> Updating the firmware will probably
resolve your issue.>> -->> Gyula HA3HZ ( )>>> >>>
|
YeeHaw! I finally got that rascal updated and seems to be working right. Now just have to wait for the open calibration cap to get here to calibrate and test some antennas and coax.Sent from my Galaxy Tab? S2
toggle quoted message
Show quoted text
-------- Original message --------From: Stan Dye <standye@...> Date: 6/17/22 10:47 PM (GMT-06:00) To: [email protected] Subject: Re: [nanovna-users] Nanovna H4 #nanovna-h4 The likely cause of your current issue is that when you upgrade from asubstantially earlier version of firmware,? you need to "clear config", andthen power-cycle the nano.? Thus clears the config variables that may beincompatible with the new firmware.? I think the "clear config" command isunder the config/expert settings menu in that firmware.There is a newer version of firmware,? which has not yet been added to thefiles section of this group. It is at DiSlord's github: down the page and click.on the NanoVNA.H4.v1.2.00.dfu file todownload it.? It will also need the clear configfollowed by re-doing thetouchscreen cal, etc.On Fri, Jun 17, 2022, 7:52 PM Mike McKinney <theranger53@...> wrote:> Well, I updated the firmware to the latest version I could find, and that> was a joke. This thing is F;;;ed now. Can turn it on but I can¡¯t calibrate> the touch and save it. I touch in the center of the screen and get the> start screen for setting the Frequency. Can¡¯t open the menu with touch only> with the button on top. Version 1.0.64 was the newest I could find. If> there is a newer one could you point me to it. This is a DiSlord version> that I found through the Absolute beginner PDF.>> Sent from Mail ( ) for> Windows>> *From:* HA3HZ ( gyula@... )> *Sent:* Friday, June 17, 2022 3:12 AM> *To:* [email protected]> *Subject:* Re: [nanovna-users] Nanovna H4 #nanovna-h4>> Mike,>> The error message means, as Hugen wrote, that you need to update the> NanoVNA firmware because the software you were using did not recognize the> command. So the firmware has not been updated for you, but the software is> waiting for new commands.>> Updating the firmware will probably resolve your issue.>> -->> Gyula HA3HZ ( )>>> >>>
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
Unfortunately some users have this problem, due to some driver conflict in
windows. It has been discussed in several prior message threads - search
for dfu driver to find them.
It is possible that the driver really did install, which you can check by
continuing with the next steps in the document which check the driver
installation. If not, likely you can fix it by continuing through the
document, installing dfuse-demo, which also installs the driver. Then
there is a section with details on troubleshooting the driver installation
which you can work through. I remember having to do a couple of these
steps on my system. Make sure for your system that you install the driver
with a 64 in the name (not x86).
If that doesn't work, search the messages as I noted above. A few users
have found that they needed to use a third party utility to clean the
driver installation before the new installation would work.
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022, 8:42 PM Fred Moore <n40cla@...> wrote: Good evening Stan,
I have had a UID and PW to STM for several years now and tried all this STM
updating the NanoVNA-H4 at least a couple of years ago. I ultimately had a
friend upgrade my Nano using his process that I did not understand. So now
I am trying to do it myself again. So I did the download from STM out of
the book you recommended to me successfully and chose to install the W8
64bit driver and it failed right off the bat. This seems like this was my
major stumbling block back in time. I literally spent a week attempting to
do this and had people telling me to read the book. Well I did this time
and I got the same message.
First, let's just install the driver, not the DfuSE DEMO software.
The driver can be downloaded from the STM32 microcontroller manufacturer's
website:
When you click
on ''Get Software'' the site will ask your e-mail address to send you an
email with a download link. Click on the link inside the received e-mail to
download zip file to your computer. Save the file en.stsw-stm32102.zip in a
separate folder and unzip it. The unzipped file contains four drivers as in
the Figure 51.
The zip file contains drivers for Windows 7 and Windows 8, 32 and 64-bit.
Win 8 drivers are OK for Win 10.
NanoVNA should not be connected to a PC yet!
To begin the installation, double-click the appropriate file, 32 or 64-bit.
If you are installing on Windows 10, select W8 (32bits or 64bits) file.
My system is a W10 64 bit system and I got the message #1626 that the
driver failed to install.
Any suggestions?
Fred - N4CLA
On Fri, Jun 17, 2022 at 6:50 PM Stan Dye <standye@...> wrote:
I don't know the difference. Note that the STM software is meant for
programming / flashing the STM processor chips - so I expect that it is
more full-featured for a programmer.
The only thing we need it for is the driver and the firmware flashing -
which is fully functional in the demo version.
On Fri, Jun 17, 2022 at 2:59 PM Fred Moore <n40cla@...> wrote:
Thank you Stan. I will give all that info a good read. So what is the
difference between the DEMO version and the latest version?
Fred - N4CLA
On Fri, Jun 17, 2022 at 4:48 PM Stan Dye <standye@...> wrote:
Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed,
and
be able to install the firmware updates. If you have upgraded to
Windows
11, these instructions have not been well-tested that I am aware of,
but
likely will still work. Note that the Dfuse-demo software is not
really
a
'demo', it is released software intended to demonstrate capabilities of
the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the
newer
software may also work, but the instructions for its use are not as
clear
(unless someone else here can clarify for you).
Stan
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote:
There have been many upgrade suggestions for the correct software
to
use
when upgrading the NanoVNA-H4 and the instructions on how to use
that
code. I have not found anything that is supposed to be golden for
the
H4.
It has all been see if this or that works. I would like to use the
STM
software. Is there a package there that is not a demo but the real
thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Mike,
DiSlords latest release for the -H line is v1.2, found here.
Download link:
Should provide a better experience.
Cheers,
Chris.
toggle quoted message
Show quoted text
On Sat, 18 Jun 2022, 12:52 pm Mike McKinney, <theranger53@...> wrote: Well, I updated the firmware to the latest version I could find, and that
was a joke. This thing is F;;;ed now. Can turn it on but I can¡¯t calibrate
the touch and save it. I touch in the center of the screen and get the
start screen for setting the Frequency. Can¡¯t open the menu with touch only
with the button on top. Version 1.0.64 was the newest I could find. If
there is a newer one could you point me to it. This is a DiSlord version
that I found through the Absolute beginner PDF.
Sent from Mail ( ) for
Windows
*From:* HA3HZ ( gyula@... )
*Sent:* Friday, June 17, 2022 3:12 AM
*To:* [email protected]
*Subject:* Re: [nanovna-users] Nanovna H4 #nanovna-h4
Mike,
The error message means, as Hugen wrote, that you need to update the
NanoVNA firmware because the software you were using did not recognize the
command. So the firmware has not been updated for you, but the software is
waiting for new commands.
Updating the firmware will probably resolve your issue.
--
Gyula HA3HZ ( )
|
The likely cause of your current issue is that when you upgrade from a
substantially earlier version of firmware, you need to "clear config", and
then power-cycle the nano. Thus clears the config variables that may be
incompatible with the new firmware. I think the "clear config" command is
under the config/expert settings menu in that firmware.
There is a newer version of firmware, which has not yet been added to the
files section of this group. It is at DiSlord's github:
Scroll down the page and click.on the NanoVNA.H4.v1.2.00.dfu file to
download it. It will also need the clear configfollowed by re-doing the
touchscreen cal, etc.
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022, 7:52 PM Mike McKinney <theranger53@...> wrote: Well, I updated the firmware to the latest version I could find, and that
was a joke. This thing is F;;;ed now. Can turn it on but I can¡¯t calibrate
the touch and save it. I touch in the center of the screen and get the
start screen for setting the Frequency. Can¡¯t open the menu with touch only
with the button on top. Version 1.0.64 was the newest I could find. If
there is a newer one could you point me to it. This is a DiSlord version
that I found through the Absolute beginner PDF.
Sent from Mail ( ) for
Windows
*From:* HA3HZ ( gyula@... )
*Sent:* Friday, June 17, 2022 3:12 AM
*To:* [email protected]
*Subject:* Re: [nanovna-users] Nanovna H4 #nanovna-h4
Mike,
The error message means, as Hugen wrote, that you need to update the
NanoVNA firmware because the software you were using did not recognize the
command. So the firmware has not been updated for you, but the software is
waiting for new commands.
Updating the firmware will probably resolve your issue.
--
Gyula HA3HZ ( )
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
Good evening Stan,
I have had a UID and PW to STM for several years now and tried all this STM
updating the NanoVNA-H4 at least a couple of years ago. I ultimately had a
friend upgrade my Nano using his process that I did not understand. So now
I am trying to do it myself again. So I did the download from STM out of
the book you recommended to me successfully and chose to install the W8
64bit driver and it failed right off the bat. This seems like this was my
major stumbling block back in time. I literally spent a week attempting to
do this and had people telling me to read the book. Well I did this time
and I got the same message.
First, let's just install the driver, not the DfuSE DEMO software.
The driver can be downloaded from the STM32 microcontroller manufacturer's
website:
When you click
on ''Get Software'' the site will ask your e-mail address to send you an
email with a download link. Click on the link inside the received e-mail to
download zip file to your computer. Save the file en.stsw-stm32102.zip in a
separate folder and unzip it. The unzipped file contains four drivers as in
the Figure 51.
The zip file contains drivers for Windows 7 and Windows 8, 32 and 64-bit.
Win 8 drivers are OK for Win 10.
NanoVNA should not be connected to a PC yet!
To begin the installation, double-click the appropriate file, 32 or 64-bit.
If you are installing on Windows 10, select W8 (32bits or 64bits) file.
My system is a W10 64 bit system and I got the message #1626 that the
driver failed to install.
Any suggestions?
Fred - N4CLA
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 6:50 PM Stan Dye <standye@...> wrote: I don't know the difference. Note that the STM software is meant for
programming / flashing the STM processor chips - so I expect that it is
more full-featured for a programmer.
The only thing we need it for is the driver and the firmware flashing -
which is fully functional in the demo version.
On Fri, Jun 17, 2022 at 2:59 PM Fred Moore <n40cla@...> wrote:
Thank you Stan. I will give all that info a good read. So what is the
difference between the DEMO version and the latest version?
Fred - N4CLA
On Fri, Jun 17, 2022 at 4:48 PM Stan Dye <standye@...> wrote:
Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed,
and
be able to install the firmware updates. If you have upgraded to
Windows
11, these instructions have not been well-tested that I am aware of,
but
likely will still work. Note that the Dfuse-demo software is not
really
a
'demo', it is released software intended to demonstrate capabilities of the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the newer
software may also work, but the instructions for its use are not as
clear
(unless someone else here can clarify for you).
Stan
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote:
There have been many upgrade suggestions for the correct software to use
when upgrading the NanoVNA-H4 and the instructions on how to use that
code. I have not found anything that is supposed to be golden for
the
H4.
It has all been see if this or that works. I would like to use the
STM
software. Is there a package there that is not a demo but the real
thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Well, I updated the firmware to the latest version I could find, and that was a joke. This thing is F;;;ed now. Can turn it on but I can¡¯t calibrate the touch and save it. I touch in the center of the screen and get the start screen for setting the Frequency. Can¡¯t open the menu with touch only with the button on top. Version 1.0.64 was the newest I could find. If there is a newer one could you point me to it. This is a DiSlord version that I found through the Absolute beginner PDF. Sent from Mail ( ) for Windows *From:* HA3HZ ( gyula@... ) *Sent:* Friday, June 17, 2022 3:12 AM *To:* [email protected]*Subject:* Re: [nanovna-users] Nanovna H4 #nanovna-h4 Mike, The error message means, as Hugen wrote, that you need to update the NanoVNA firmware because the software you were using did not recognize the command. So the firmware has not been updated for you, but the software is waiting for new commands. Updating the firmware will probably resolve your issue. -- Gyula HA3HZ ( )
|
Re: NanoVNA 4 version 1.0.? Only save at 800Hz
Hmmm... sorry, haven't seen this before. Looks like something hijacked
your cal to be done at a cw freq of 800, rather than the range you wanted.
I would just reset the cal and do it again.
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022, 3:59 PM John Mount, W7OTD <jwmount@...> wrote: Thank you Stan, I did not hit the CW frequency. It is a showing up on its
own while saving to a location as 800Hz.
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
FYI, for non Windows users, the ST Cube programmer works on the Nano as well, but requires .bin files (provided by Huygen).
toggle quoted message
Show quoted text
On June 17, 2022 5:49:42 PM CDT, Stan Dye <standye@...> wrote: I don't know the difference. Note that the STM software is meant for
programming / flashing the STM processor chips - so I expect that it is
more full-featured for a programmer.
The only thing we need it for is the driver and the firmware flashing -
which is fully functional in the demo version.
On Fri, Jun 17, 2022 at 2:59 PM Fred Moore <n40cla@...> wrote:
Thank you Stan. I will give all that info a good read. So what is the
difference between the DEMO version and the latest version?
Fred - N4CLA
On Fri, Jun 17, 2022 at 4:48 PM Stan Dye <standye@...> wrote:
Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed, and
be able to install the firmware updates. If you have upgraded to Windows
11, these instructions have not been well-tested that I am aware of, but
likely will still work. Note that the Dfuse-demo software is not really a
'demo', it is released software intended to demonstrate capabilities of the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the newer
software may also work, but the instructions for its use are not as clear
(unless someone else here can clarify for you).
Stan
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote:
There have been many upgrade suggestions for the correct software to use
when upgrading the NanoVNA-H4 and the instructions on how to use that
code. I have not found anything that is supposed to be golden for the H4.
It has all been see if this or that works. I would like to use the STM
software. Is there a package there that is not a demo but the real
thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
|
Just upgraded to an SAA2-N. Looks like a very solid piece of gear. Which software are users here using for theirs. DisLord or Saver? I plan to use Windows 10 and perhaps Linux with a Pi in the future.
|
Re: NanoVNA 4 version 1.0.? Only save at 800Hz
Thank you Stan, I did not hit the CW frequency. It is a showing up on its own while saving to a location as 800Hz.
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
I don't know the difference. Note that the STM software is meant for
programming / flashing the STM processor chips - so I expect that it is
more full-featured for a programmer.
The only thing we need it for is the driver and the firmware flashing -
which is fully functional in the demo version.
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 2:59 PM Fred Moore <n40cla@...> wrote: Thank you Stan. I will give all that info a good read. So what is the
difference between the DEMO version and the latest version?
Fred - N4CLA
On Fri, Jun 17, 2022 at 4:48 PM Stan Dye <standye@...> wrote:
Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed, and
be able to install the firmware updates. If you have upgraded to Windows
11, these instructions have not been well-tested that I am aware of, but
likely will still work. Note that the Dfuse-demo software is not really a
'demo', it is released software intended to demonstrate capabilities of the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the newer
software may also work, but the instructions for its use are not as clear
(unless someone else here can clarify for you).
Stan
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote:
There have been many upgrade suggestions for the correct software to use
when upgrading the NanoVNA-H4 and the instructions on how to use that
code. I have not found anything that is supposed to be golden for the H4.
It has all been see if this or that works. I would like to use the STM
software. Is there a package there that is not a demo but the real
thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
Thank you Stan. I will give all that info a good read. So what is the
difference between the DEMO version and the latest version?
Fred - N4CLA
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 4:48 PM Stan Dye <standye@...> wrote: Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed, and
be able to install the firmware updates. If you have upgraded to Windows
11, these instructions have not been well-tested that I am aware of, but
likely will still work. Note that the Dfuse-demo software is not really a
'demo', it is released software intended to demonstrate capabilities of the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the newer
software may also work, but the instructions for its use are not as clear
(unless someone else here can clarify for you).
Stan
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote:
There have been many upgrade suggestions for the correct software to use
when upgrading the NanoVNA-H4 and the instructions on how to use that
code. I have not found anything that is supposed to be golden for the H4.
It has all been see if this or that works. I would like to use the STM
software. Is there a package there that is not a demo but the real thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Re: NanoVNA 4 version 1.0.? Only save at 800Hz
When you say you "set the stimulation to 7.025 - 7.3MHz for both CW and
SSB", did you press the "CW Freq" menu item as part of this action? And
did you 'save' the calibration to the slot?
Typically when we say we are going to "verify a calibration", we just
attach the 'open', 'short', and 'load' standards in turn, and look a the
display to verify that they each show the correct values, which are a point
a the far right of the Smith chart, a point at the far left, and a point in
the center (respectively).
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 1:14 PM John Mount, W7OTD <jwmount@...> wrote: NanoVNA 4 version 1.0.?
I had all slots filled with band segments mainly SSB 5.3305 - 29.7MHz, 3.8
- 4MHz, 7.175 - 7.3MHz, etc. I decided to verify the calibration, I set the
stimulation to 7.025 - 7.3MHz for both CW and SSB, then performed the
calibration and the slot now shows cw 800Hz - 800Hz. What have I done
wrong?
Thank you, 73,
John W7OTD
|
Re: Where can I find the latest STM upgrade SW download for a NanoVNA-H4
Fred,
If you follow *exactly *the instructions in the latest version of the
"Absolute Beginner's Guide" (available in the files section here in this
group), you will have the correct STM software and drivers installed, and
be able to install the firmware updates. If you have upgraded to Windows
11, these instructions have not been well-tested that I am aware of, but
likely will still work. Note that the Dfuse-demo software is not really a
'demo', it is released software intended to demonstrate capabilities of the
STM processors. And yes, the website notes that it is replaced by newer
software, but still has it there for download. I understand the newer
software may also work, but the instructions for its use are not as clear
(unless someone else here can clarify for you).
Stan
toggle quoted message
Show quoted text
On Fri, Jun 17, 2022 at 1:21 PM <n4cla@...> wrote: There have been many upgrade suggestions for the correct software to use
when upgrading the NanoVNA-H4 and the instructions on how to use that
code. I have not found anything that is supposed to be golden for the H4.
It has all been see if this or that works. I would like to use the STM
software. Is there a package there that is not a demo but the real thing
and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Where can I find the latest STM upgrade SW download for a NanoVNA-H4
There have been many upgrade suggestions for the correct software to use when upgrading the NanoVNA-H4 and the instructions on how to use that code. I have not found anything that is supposed to be golden for the H4. It has all been see if this or that works. I would like to use the STM software. Is there a package there that is not a demo but the real thing and then I need the latest DFU file.
Thanks
N4CLA - Fred
|
Mike McKinney
F4WCV