开云体育

Hi Art, Thanks for checking that out! Happy Birthday! That's quite a milestone. Must be all those years of living right, plus a liberal application of cutting fluid now and then :-) Rest assured, if I

OK, downloaded the zip file and loaded the dir into eagle 6.1 that I use and seems to work just fine. Did some poking around and all seemed fine. Country

JJ, Will do as soon as I can setup Eagle on my new machine. Had a crash and have to start all over again. You know how that goes! Country

1 New Commit: [pcbgcode:master] By John Johnson <john@...>: 0d990f9637d0 ( https://github.com/JohnAtl/pcbgcode/commit/0d990f9637d0ab399fd7f4bb1607514010f890d6 ) : This should be 3.6.2.4.

2 New Commits: [pcbgcode:master] By John Johnson <john@...>: ab618f41ca6e ( https://github.com/JohnAtl/pcbgcode/commit/ab618f41ca6e195803fcf70e1e5b8fb055e91d8f ) : Not sure why these jars

1 New Commit: [pcbgcode:master] By John T. Johnson <JohnAtl@...>: d5f7f8f3ee76 ( https://github.com/JohnAtl/pcbgcode/commit/d5f7f8f3ee766acc68319dd7f5dad5d564e61e51 ) : Update

I've been using other forums that run on [Discourse](https://www.discourse.org/features). I think they are easier to navigate than groups.io (and Discord), as everything here seems to run together. I

I just uploaded what should be version 3.6.2.4 to GitHub, and would appreciate anyone who can verify that it works. I had some older files on there, 3.6.0.x. I don't currently have anything set up to

Write it down so next time , if there is, you can see how you solved it. Sent: Sunday, January 9, 2022 8:22 AM To: [email protected] Subject: Re: [pcbgcode] Newbie Error? #pcbgcode Hi Bruce Thanks

Hi Bruce Thanks very much for the reply. It seems to be solved and something to do with the GND polygon. I deleted the polygon that was there- redid it and it was back to how I intended.. All very

I believe you need to go into pcb-gcode-setup and tell it which layer to etch, top or bottom only.

Hi Guys This is my first attempt at using Eagle and PCB_Gcode. I have a very simple 12 keypad with smt resistor network. All was going well and Eagle looks good with top layer as expected with tracks

Can someone remind me what java I need to run the viewer.Could not find docs on this. I'm using Eagle 7.7 on OSX Big Sur. Eagle works fine and pcb-gcoderuns and generates files. just no viewer.

The answer is in the pcb-gcode-setup ulp. See below This is my setup for a 0.2mm milling tool (no chemical etching in my work). I set the minimum to less than the cutting tool diameter to ensure a

I am new to Mach 3 setup and commands and I have a question.. Is there a G-code command I can use to populate Tool Table in Mach3 in a way that every tool change the operator can see TOOL DIAMETER in

Hi, Thank you for this great plugin for Eagle :-) It works perfect in combination with my StepCraft CNC mill for pcb projects. I have recently installed Eagle+pcbgcode on a new machine. Everything

Well it looks like the problem is something to do with M6 tool change codes !! Had a look around and found this info about the M6 command not work in all So i downloaded the ( grbl.pp ) file and put

Hi Thanks for that mate will give it a go tomorrow Howard

Howard Here is what you need in your drill file, as far as I understand. You will have to do the formatting (tabs & spaces, as written in the instructions at the top of the sample file. T01 0.300