开云体育

I assume so... As I mentioned I am new at Node-Red... 73, and thanks, Dave (NK7Z) https://www.nk7z.net ARRL Volunteer Examiner ARRL Technical Specialist, RFI ARRL Asst. Director, NW Division,

Adrian, That generates pages, and pages of output... Should there be a grep there someplace? 73, and thanks, Dave (NK7Z) https://www.nk7z.net ARRL Volunteer Examiner ARRL Technical Specialist, RFI

I believe you are asking if there is any code in the section for code for the file node, (is that called a function as well as a node?), nothing is in that part. 73, and thanks, Dave (NK7Z)

Hi Adrian, I'll check if it's a utf16 issue... and if that fails, I'll issue a temp update with a radio type dropdown as you suggest.? I'm out for breakfast now and I have lawn mowing etc to do

Let me absorb this a bit... I am quite new to Node-Red, and have never even heard of the visudo before... I have learned to understand what changes I make first though, so I am going slow and careful

BTW, the file is created by a perl script I run under dcole, same group the file is owned by. 73, and thanks, Dave (NK7Z) https://www.nk7z.net ARRL Volunteer Examiner ARRL Technical Specialist, RFI

Hi Adrian, Here are the results: dcole@nostromo:~$ stat /home/dcole/scripts/solar_data/incoming/lotwcount.txt File: /home/dcole/scripts/solar_data/incoming/lotwcount.txt Size: 3 Blocks: 8 IO Block:

Hi Mick, Thank you for the assistance, here are the results: -rw-rw-rw- 1 dcole dcole 3 Jun 11 05:20 /home/dcole/scripts/solar_data/incoming/lotwcount.txt 73, and thanks, Dave (NK7Z)

If the permissions are set correctly the only other reason I would think node red could not read the file is that node red is not apart of the group.

Hi Adrian, I created two dynamic dropdown lists, and each one works. Then I added a Switch node to select what list should be used, based on the getradio response.? ? I'm stuck ... but I wanted to

Dave Perhaps the file is in a directory that requires administrative privileges?? I suggest two ideas. 1- Move the file to different locations, like the documents directory. 2- prepend a "sudo" to

Dave can? you run the following command and print the output: ls -l /home/dcole/scripts/solar_data/incoming/lotwcount.txt -- Mick, W8BE

Hi, I am trying to read a file under Ubuntu... The file is under my home directory, as shown in the screen capture... I am using readfile, and all permissions are set to read/write for everyone on

You can set a jumper in the meter or use a Y cable and connect two sensors parallel. The sensor with highest reading will show output. This is fine for amp output in SO2R but will not show input and

Can it show these for both inputs to the PowerMaster or just one?? Non praeses meus Those who would give up essential liberty, to purchase a little temporary safety, deserve neither liberty nor

Hi All, Making progress with Power Master II watt meter flow. I've got metering working as well as alarm indication for high SWR and High Forward Power. These can be set in meter to auto reset or be

Hello all, Working on a flow for the Array Solutions Power Master II watt meter. I have most of it working except a couple of commands where I cannot determine the CRC checksum. I am NOT a programmer

Hey David I have been following your stream on integrating Stream deck into Node Red. I have managed to get my Icom IC-7300 to display the frequency on the display dashboard using the CIV get freq

I gave a presentation to the Arizona Outlaws Contest Club last night, mainly about my contesting dashboard, but they wanted to know more about the basics of Node Red.? I put together about 3

Hi Joe I do not have a 1x3 TG to test with. Email me direct and we can try to work on it remotely. I will do some research on my end in the meantime. 73 Dave wo2x Sent from my waxed string and tin