开云体育

Hi there, I?m using the OM Module to switch stackmatches, but it works only with the windows tool for me. I?m not so deep into nodered that I?ll be able to program this. The other side is, that it

Thanks to all. I appreciate the help. -- Bill - N1HKO

The WiKi on this site has a step by step tutorial on installing the OS on the Pi as well as configuring Node Red and being ready to load your first flow. 73 Dave wo2x Sent: Monday, March 31, 2025

Bill, I am a neophyte when it comes to Node Red and Raspberry Pi's. I've started with a #310 and a #321 card here https://www.packtenna.com/store/c10/Station_Control_Modules.html#/ The #310 has a Pi

Bill Either a 4 or a 5 will suit your needs. Vilros has both models available. Be sure to purchase the correct power supply with the model you purchase as it will have the correct amperage. Prices are

Hi All, I'm moving my Node RED flows for TGXL control from Windows to a Rasp Pi. I have never owned or used a Pi and know just the basics. In addition to the Pi, I need a minimum of a 10 pin GPIO. Can

Check out this video. Simple 4 relay flow that walks you through creating the flow. https://youtu.be/Q1p5wd22tKQ?si=j0bh-P0qh2NhXZnt 73 Dave wo2x Sent: Sunday, March 30, 2025 12:34 PM To:

I am participating in a youth project and I'm in need of some minor custom flows. Mainly relays on/off. It shouldn't be too bad but it's over my head to build from scratch. Please contact me offline

Frank, Zoom work? If so I'll send a meeting link in 15-20 minutes. Have to drop off a package to a neighbor that got delivered to me by mistake. Send email direct to my QRZ.COM listed address. Ron

After thinking about the error a bit more, I realized that the GetNumber node may be erroring because it's not seeing any data at all.? That might indicate that I in fact do not have the serial port

Thanks, Ron. Yes, I should have been more explicit with what I'm seeing. As mentioned in the title, the error is in the GetNumber node.? It is barfing on the "trim" command. I'm running the WB0SMX

Frank, there are several flows in the files section of the group for the ERC including one of mine. I'm not sure which one you're using and suggest you elaborate and possibly include some debug nodes

Hi I? do not own a flexradio but I am helping VA2UR with his remote contest station. We want to capture the current transmit band , before starting transmission if possible. I am able to capture the

I'm trying to get ERC Rotor Control working with my Yaesu G-450A rotor controller and Node-Red.? The ERC works fine on Windows, but I'm getting an error when I connect it to Node-Red. I've imported

Contact me at support AT mkcmsoftware DOT com. Please send me a the list of settings that are not being restored. Have you tried to use FRStack Memory to recall mode and other settings? 73, Mark

*HELP with FRStack* I have configured my FLEX6600 (XVTR settings) for use with several transverters 144, 432, 1296 MHz…………. Selecting the different transverters from the Flex *Band selector*

Rich, Here you go. I just modified the original flow to have both rotators visible at once. 73, George / W7GES [email protected]> wrote:

Thanks Tim, I'll take a look at the files. I was successful with my first Node Red function. I was able to turn the Flex 8600 on and off with one of the relays on Georges #321 GPIO card. It was quite

Rich: From the Group web page, ( /g/nodered-hamradio )?there is a section on the left hand page that has links: (/g/nodered-hamradio/files (

George, Yes, please send the flow. Rich - N5ZC