开云体育

My amp is also a series 1 but that does not matter as it is a 1.3K so it uses the same protocol for all 1.3, 1.5 and 2.0 models. Mark Sent: Tuesday, February 23, 2021 4:07 PM To:

Paul Regarding "unused configuration nodes". ?That is a housekeeping item only. ?It Will not affect the functioning of your flow. I like to "delete" "unused configuration nodes" from time to time to

Paul Com looks good. I would next try making "SPEProtocolV1". "false" I am not knowledgeable on all aspects of the SPE versions, but I have set up three other hams with SPE1.3K amps and we used

Here is my Appsettings. "SvcConfig": { "AutoConnect": "true", "initRadioName": null, "initClientName": null, "MRUMatchDelta": "0.000999", "FollowActiveSlice": "true", "MuteOthersOnSliceActive":

Hi Alan, I have pasted the by-id into the appsettings file it now reads?/dev/serial/by-id/usb-FTDI_USB_Serial_Converter_FTGCBLZT-if00-port0? ?but I am still not getting anything as far as

Mark, if you check here http://www.spetlc.com/en/download-3kfa-uk.html you will see there are manuals and firmware for first and second series of the 1.3k-FA mine is the first series which included

Mark That’s too bad. It should reply some text. The Windows version has a hook into smartlink selection. Impossible for me to connect remotely. 73, Marty

Having the SWR show last value when in receive is actually a good thing in my mind. If I happen to not notice during TX that the SWR is creeping up but glance during RX I know I can check it,

I have to ask about "set the SPEProtocolV1 to true as it is an early version of the 1.3K-FA". To my knowledge the V1 protocol should only be used by SPE V1 AMP. What is an "early version of the

Paul Your path looks good, except paste in the path to the "by-id" link of the FTDI cable. This is what my FTDI cable looks like. Your FTDI cable number will be different.

I have my expert connected to usb port on the Raspberrypi I get this from /dev/serial/by-path...... /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.3:1.0-port0 I have entered that

Hi Mike I have sent him emails for the last year or 2 and he really hasn't commented on how I made his LP100 web based and he wasn't really interested. It was just last week that he finally replied to

Just a FWIW... ?I have node Node-Red installed and running on a PI-Zero-W.? I am using it as an internal controlled in a piece of station equipment which requires using the several GPIO ports.

It is replying while disconnected otherwise you would get an error. Its reply is a n empty string. Connect to a radio to see a populated object. Mark W3II

Alan The status sys it is active (running). I still get a blank response on local browser and using the ip address of the pi. Maybe it needs to find a radio and connect first. It can't because I am in

I'd like to thank Larry Phipps (N8LP) for providing me this information and with his? permission I'd like to share it here in the group, that should be helpful to bring the LP-500/700 into the

Maty Below is my browser return when I enter, ? "http://192.168.50.214:5025/Radio/INFO". ? ? Where 192.168.50,214 is the IP address of my Raspberry Pi running FRStack. Are you sure FRStack is

Marty, use the ip address of your Pi, for example, mine is: http://192.168.1.23:5025/Radio/INFO 73, Mike Kovacich - VE3CKO -

Alan I get a blank screen when I enter?http://localhost:5025/Radio/INFO?using VNC to get to the browser on the Pi. I think I am going to have to wait until I get back home and can put my developent

Marty For example, use the REST command to get "info" from Flex. ?Just enter this into your web browser, and you will see the return packet. You can also use other devices to send Web-Based REST