Here is my Appsettings.
?"SvcConfig": {
? ? "AutoConnect": "true",
? ? "initRadioName": null,
? ? "initClientName": null,
? ? "MRUMatchDelta": "0.000999",
? ? "FollowActiveSlice": "true",
? ? "MuteOthersOnSliceActive": "false",
? ? "EnableTxOnSliceActive": "false",
? ? "TempUnitInF": "true",
? ? "PgxlTuneStandby": "true", // this will set AMP to STANDBY when TUNE is activated
? ? "PgxlModeRestore": "true", // this will return AMP to OPERATE after TUNE complete
? ? "PgxlRadioMaxPower": "50", // this is MAX radio power level when AMP is OPERATE
? ? "PgxlRadioStandbyPower": "100", // this is MAX radio power level when AMP is STANDBY
? ? "PGXLOnAntenna": "0", // 0 or 1 or 2; 0 for both, 1 for ANT1, 2 for ANT2
? ? "RCATXACCTuneDisable": "false",
? ? "RCATX1TuneDisable": "false",
? ? "RCATX2TuneDisable": "false",
? ? "RCATX3TuneDisable": "false",
? ? "RadioTuneModeDetect": "true", // this is set true if you want to detect a Radio Tune button push, remember to set TX Delay on radio
? ? "SPEComPort": "/dev/serial/by-id/usb-FTDI_USB_Serial_Converter_FTGCBLZT-if00-port0", // this is the Serial device for SPE AMP Control port (Not the CAT port)
? ? "SPETuneStandby": "false", // this will set SPE to STANDBY when TUNE is activated
? ? "SPEModeRestore": "false", // this will return SPE to OPERATE after TUNE complete
? ? "SPEOnAntenna": "0", // 0 or 1 or 2; 0 for both, 1 for ANT1, 2 for ANT2
? ? "SPEUseDTR": "false", // this will set DTR to power up amp
? ? "SPEProtocolV1": "true", // this is set true for SPE V1 amps
? ? "SPEAutoOpen": "false", // this is set true to OPEN SPE after connecting to radio
? ? "SteppIRComPort": ",9600,None,One,0,false,true,1,2", // port,baud,parity,stop,FollowAntInt,EnabledBool,SyncManualBool,AntTxInhibitInt,AntType eg. "/dev/ttyUSB0,9600,None,One,0,true,true,1,1"
? ? "FDXProtect": "false,false,false,false,false,false", // enabled,ant1,ant2,rxa,rxb,wide
? ? "UDPSettings": "false,255.255.255.255,12070,false,127.0.0.1,12071,false,127.0.0.1,12072,false,127.0.0.1,12073", // enabled,IPADDR,PORT, enabled,IPADDR,PORT, enabled,IPADDR,PORT, enabled,IPADDR,PORT?
? ? "UDPMeterSettings": "false,255.255.255.255,12270,false", // enabled,IPADDR,PORT,SMeterEnabled
? ? "ModeSetsDax": "0", // 0 - Disable, 1 - turn DAX on when mode is DIGL/H, 2 - turn DAX off if not DIGL/H, 3 - both
? ? "CustomFunctions": "",
?
