Re: File /Flex3000Flow.rtf uploaded
#file-notice
I have them set to "Rocket" Charlie KB8CR
By
Charlie Rubenstein
·
#1781
·
|
Re: File /Flex3000Flow.rtf uploaded
#file-notice
Check your meter nodes in node red and to see how you have animations set. AL, K0VM
By
Al Groff
·
#1780
·
|
Re: Frstack running fine until I enable the SPE part
Hi Paul, Thanks for letting us know. I fo have any pointers since it is fresh in your mind please let me know. I can add a SPE section to the WiKis to help the next person. 73 Dave wo2x Sent:
By
Dave wo2x
·
#1779
·
|
Re: Frstack running fine until I enable the SPE part
Thanks Alan for the offer, but i finally got it running. I didn't realise that you had to hit the open button on the spe dashboard to get it to read the serial port, it is all now working as it
By
Paul Menown
·
#1778
·
|
Re: File /Flex3000Flow.rtf uploaded
#file-notice
I wonder if it would be more responsive, if I ran NodeRed on the computer that is running PowerSDR, and use virtual serial ports, rather than the TCP serial server. Right now, I'm running NodeRed on
By
Charlie Rubenstein
·
#1777
·
|
Re: File /Flex3000Flow.rtf uploaded
#file-notice
Dave: Hope you're feeling better. I went out for the first time in a LONG time, to pick my brother up from the airport. Had two masks on.....Fauci would approve.ha ha. I got busy here with business
By
Charlie Rubenstein
·
#1776
·
|
Re: Frstack running fine until I enable the SPE part
Paul I cannot help you any further because I lack knowledge of your configuration (virtual here). Perhaps others can comment. Another approach is to build a separate Raspberry Pi SD card dedicated
By
Alan Blind, WA9WUD
·
#1775
·
|
Re: Frstack running fine until I enable the SPE part
Virtual here is not running I only used it to check communication with the amp via the pi.. It is not in the equation when running node red or frstack. Paul Gi4fzd
By
Paul Menown
·
#1774
·
|
Re: Frstack running fine until I enable the SPE part
Paul You have introduced new variables, which I cannot comment on all. Your question about opening port 5025. Not sure how that enters into your configuration. Normally, TCP Port 5025 is used by
By
Alan Blind, WA9WUD
·
#1773
·
|
Re: Frstack running fine until I enable the SPE part
I Checked the amp firmware, it has the same date but has B_15s at the end rather than C_15s the page advises only to update if the date is earlier so I am reluctant to update. Not sure if that would
By
Paul Menown
·
#1772
·
|
Re: Frstack running fine until I enable the SPE part
Paul And, just in case you are not doing so, shutdown and restart FRstack after making config file changes. Following the restart command, verify FRStack starts up. Shutdown. sudo systemctl stop
By
Alan Blind, WA9WUD
·
#1771
·
|
Re: Frstack running fine until I enable the SPE part
Paul Also, verify that FRStack is running by running the command: systemctl status FRStackWebApi Alan
By
Alan Blind, WA9WUD
·
#1770
·
|
Re: Frstack running fine until I enable the SPE part
Paul Try using the default USB port path. This will work if you have one USB cable. Debian will assign USB0 to the first cable and then each additional cable in sequence: /dev/ttyUSB0 Did you verify
By
Alan Blind, WA9WUD
·
#1769
·
|
Re: Frstack running fine until I enable the SPE part
I updated to FRStackWebApiRPi_3_1_27_56 Still getting the following error, (it doesn't seem to matter whether set at true or false in the appsettings) 24 Feb 11:46:35 - [warn] [http
By
Paul Menown
·
#1768
·
|
Re: Frstack running fine until I enable the SPE part
I will be releasing an update to FRStackWebApi shortly for all platforms. This updates the SPE Amp serial port logic to address an issue that showed up when I switched to .NET 5. In the meantime RPi
By
Mark Hanson
·
#1767
·
|
Re: Frstack running fine until I enable the SPE part
My amp is also a series 1 but that does not matter as it is a 1.3K so it uses the same protocol for all 1.3, 1.5 and 2.0 models. Mark Sent: Tuesday, February 23, 2021 4:07 PM To:
By
Mark Hanson
·
#1766
·
|
Re: Frstack running fine until I enable the SPE part
Paul Regarding "unused configuration nodes". ?That is a housekeeping item only. ?It Will not affect the functioning of your flow. I like to "delete" "unused configuration nodes" from time to time to
By
Alan Blind, WA9WUD
·
#1765
·
|
Re: Frstack running fine until I enable the SPE part
Paul Com looks good. I would next try making "SPEProtocolV1". "false" I am not knowledgeable on all aspects of the SPE versions, but I have set up three other hams with SPE1.3K amps and we used
By
Alan Blind, WA9WUD
·
#1764
·
|
Re: Frstack running fine until I enable the SPE part
Here is my Appsettings. "SvcConfig": { "AutoConnect": "true", "initRadioName": null, "initClientName": null, "MRUMatchDelta": "0.000999", "FollowActiveSlice": "true", "MuteOthersOnSliceActive":
By
Paul Menown
·
#1763
·
|
Re: Frstack running fine until I enable the SPE part
Hi Alan, I have pasted the by-id into the appsettings file it now reads?/dev/serial/by-id/usb-FTDI_USB_Serial_Converter_FTGCBLZT-if00-port0? ?but I am still not getting anything as far as
By
Paul Menown
·
#1762
·
|