Re: L32 + FlexRadio, issue?
Works fine.
Thanks for info Frank and Bob.
Correct config is CW|CWL to work with Radio 1 and Radio 2
Many thanks!
?
Fabi¨¢n Malnero Maccari, EB1TR
Hi Fabian,
?
Smartsdr understands cwl or cwu NOT cw and you must change the radio mode in bands&modes to cwl or cwu - whichever sideband you have configured in Smartsdr. You really need to read section 2.5.1 of the excellent manual and you also need to read and apply
Hinsons tip on page 42. Logger32 when configured correctly works flawlessly with Smartsdr.
73, Frank GI4NKB
|
Bob,
I do not think so. I have changed to CWU and USB, but it did not help, please...
Best regards, Alec
------ Wiadomo?? oryginalna ------
Data 02.05.2025 11:37:40
Temat Re: [hamlogger] $command #ModeModifier#;$
I haven't tested this, but is the problem that SmartSDR does not have a mode of CW, it uses CWL or CWR. SeventyThree(s).?
?
On 05/02/2025 5:04 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote:
?
?
?
Hi,
?
I have tested the following RCP DX Spot macro set-ups:
?
 ?
?
All is OK, except for #ModeModifier#
which?is supposed to change the radio filters depending on the mode.
Commands are correct - when applied directly. they work beautifully,
e.g.
?
?
Is the?#ModeModifier#?syntax wrong in my set-up?
Help me, please...
?
Best regards,
Alec
|
Section 34.9 (page 780) of the help file is dedicated to this topic. SeventyThree(s).
On 05/02/2025 7:59 AM EDT sp5ewx via groups.io <sp5ewx@...> wrote:
?
?
Hi Dirk ...thank you ...will do that
73's
Mike sp5ewx
Mike
?
Check in task manager what kind of programs are unnecessary running.??? Junk can slowndown ur pc and eating memory.
Dirk on4ct
?
?
|
Hi Dirk ...thank you ...will do that
73's
Mike sp5ewx
Mike
?
Check in task manager what kind of programs are unnecessary running.??? Junk can slowndown ur pc and eating memory.
Dirk on4ct
|
Re: L32 + FlexRadio, issue?
Hi Fabian,
?
Smartsdr understands cwl or cwu NOT cw and you must change the radio mode in bands&modes to cwl or cwu - whichever sideband you have configured in Smartsdr. You really need to read section 2.5.1 of the excellent manual and you also need to read and apply Hinsons tip on page 42. Logger32 when configured correctly works flawlessly with Smartsdr.
73, Frank GI4NKB
|
Re: L32 + FlexRadio, issue?
You haven't read the manual have you? Try CW/CWL This sets the radio mode as CW for radio 1, and CWL for radio 2. SeventyThree(s).
On 05/02/2025 5:30 AM EDT Fabian/EB1TR via groups.io <fabian@...> wrote:
?
?
Thanks Frank for answer¡
?
This is my config (band/mode) for 40m (for example). This works OK on my RADIO 1 (Elecraft K3) but wrong mode, as I said, on RADIO 2 (FlexRadio 8400).
?
?
Thanks!
Fabi¨¢n Malnero Maccari, EB1TR
El 2 may 2025, a las 11:21, Frank Hunter via groups.io <gi4nkb@...> escribi¨®:
Hi Fabian,
In Smartsdr navigate to settings -> radio setup -> phone/cw and select which sideband you wish to use in cw either CWL or CWU,? CWL preferred.
In Logger32 navigate to Tools -> setup bands & modes? and make sure that the cw sections of the bands are configured to use which sideband you selected in Smartsdr.
I've attached an image that probably shows what I mean better than I just typed :-)
73, Frank GI4NKB
<smartsdr.jpg>
|
I haven't tested this, but is the problem that SmartSDR does not have a mode of CW, it uses CWL or CWR. SeventyThree(s).?
?
On 05/02/2025 5:04 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote:
?
?
?
Hi,
?
I have tested the following RCP DX Spot macro set-ups:
?
 ?
?
All is OK, except for #ModeModifier#
which?is supposed to change the radio filters depending on the mode.
Commands are correct - when applied directly. they work beautifully,
e.g.
?
?
Is the?#ModeModifier#?syntax wrong in my set-up?
Help me, please...
?
Best regards,
Alec
|
Re: L32 + FlexRadio, issue?
Thanks Frank for answer¡
This is my config (band/mode) for 40m (for example). This works OK on my RADIO 1 (Elecraft K3) but wrong mode, as I said, on RADIO 2 (FlexRadio 8400).
Thanks!
Fabi¨¢n
Malnero Maccari, EB1TR
toggle quoted message
Show quoted text
El 2 may 2025, a las 11:21, Frank Hunter via groups.io <gi4nkb@...> escribi¨®:
Hi Fabian,
In Smartsdr navigate to settings -> radio setup -> phone/cw and select which sideband you wish to use in cw either CWL or CWU,? CWL preferred.
In Logger32 navigate to Tools -> setup bands & modes? and make sure that the cw sections of the bands are configured to use which sideband you selected in Smartsdr.
I've attached an image that probably shows what I mean better than I just typed :-)
73, Frank GI4NKB
<smartsdr.jpg>
|
Re: L32 + FlexRadio, issue?
Hi Fabian,
In Smartsdr navigate to settings -> radio setup -> phone/cw and select which sideband you wish to use in cw either CWL or CWU,? CWL preferred.
In Logger32 navigate to Tools -> setup bands & modes? and make sure that the cw sections of the bands are configured to use which sideband you selected in Smartsdr.
I've attached an image that probably shows what I mean better than I just typed :-)
73, Frank GI4NKB
|
Re: L32 + FlexRadio, issue?
Look at your BandPlan (TOOLS?| SETUP BANDS & MODES).
Column 6 for Radio Mode
What is the Radio Mode set to on the CW rows??
Flex radios do not have a "CW" radio mode, they use CWL or CWR.
?
SeventyThree(s).
?
On 05/02/2025 4:11 AM EDT Fabian/EB1TR via groups.io <fabian@...> wrote:
?
?
Debug data:
?
?
?
Fabi¨¢n Malnero Maccari, EB1TR
El 2 may 2025, a las 9:55, Fabian/EB1TR via groups.io <fabian@...> escribi¨®:
Good morning,
I have a problem and I'm not sure if it could be related to configuration.
When I change frequency, the mode change command to CW doesn't seem to be sent correctly.
Switching to USB and LSB works fine, but L32 appears to send ZZMD00 for CW frequencies, where I believe it should be ZZMD04.
Any ideas?
Fabi¨¢n Malnero Maccari, EB1TR
|
Hi,
I have tested the following RCP DX Spot macro set-ups:
 ? 
All is OK, except for #ModeModifier# which?is supposed to change the radio filters depending on the mode. Commands are correct - when applied directly. they work beautifully, e.g. ?
Is the?#ModeModifier#?syntax wrong in my set-up? Help me, please...
Best regards, Alec
|
Re: L32 + FlexRadio, issue?
Debug data:
Fabi¨¢n
Malnero Maccari, EB1TR
toggle quoted message
Show quoted text
El 2 may 2025, a las 9:55, Fabian/EB1TR via groups.io <fabian@...> escribi¨®:
Good morning,
I have a problem and I'm not sure if it could be related to configuration.
When I change frequency, the mode change command to CW doesn't seem to be sent correctly.
Switching to USB and LSB works fine, but L32 appears to send ZZMD00 for CW frequencies, where I believe it should be ZZMD04.
Any ideas?
Fabi¨¢n
Malnero Maccari, EB1TR
|
Good morning,
I have a problem and I'm not sure if it could be related to configuration.
When I change frequency, the mode change command to CW doesn't seem to be sent correctly.
Switching to USB and LSB works fine, but L32 appears to send ZZMD00 for CW frequencies, where I believe it should be ZZMD04.
Any ideas?
Fabi¨¢n
Malnero Maccari, EB1TR
|
Mike
?
Check in task manager what kind of programs are unnecessary running.??? Junk can slowndown ur pc and eating memory.
Dirk on4ct
|
Re: WSJT not call on cherry picking
Lorenzo Cherry-picking works fine here with WSJTX. However, note that... If "Hold TX Freq" option is unchecked, then WSJTX call him only if he is calling CQ.
On 2025-05-02 ½ð 14:11:15, Lorenzo IK0HFO via groups.io <l.locicero@...> wrote: hi
wsjt not call on cherry picking ...charge all data but do not call
jtdx instead works fine
any suggestion?
73' de
IK0HFO
Lorenzo
|
WSJT not call on cherry picking
hi
wsjt not call on cherry picking ...charge all data but do not call
jtdx instead works fine
any suggestion?
73' de
IK0HFO
Lorenzo
|
Yes, there are many logging programs. I am sure you can find one that does not hang on your computer. SeventyThree(s).
On 05/01/2025 9:37 AM EDT sp5ewx via groups.io <sp5ewx@...> wrote:
?
?
Is it only solution??? You mean new program different than L32?
Mike sp5ewx
Either a new computer, or a new logging program. SeventyThree(s).
?
?
My logger 32 has been hanging up for some time now for no reason. For example, I want to enter a new QSO or click on the rotor control. It stops responding and I can't close it even with Ctrl+Alt+Del. I need to restart my computer. Any suggestions??
sp5ewx
?
?
|
Is it only solution??? You mean new program different than L32? Mike sp5ewx
Either a new computer, or a new logging program. SeventyThree(s).
?
?
My logger 32 has been hanging up for some time now for no reason. For example, I want to enter a new QSO or click on the rotor control. It stops responding and I can't close it even with Ctrl+Alt+Del. I need to restart my computer. Any suggestions??
sp5ewx
|
Either a new computer, or a new logging program. SeventyThree(s).
On 05/01/2025 8:42 AM EDT sp5ewx via groups.io <sp5ewx@...> wrote:
?
?
My logger 32 has been hanging up for some time now for no reason. For example, I want to enter a new QSO or click on the rotor control. It stops responding and I can't close it even with Ctrl+Alt+Del. I need to restart my computer. Any suggestions??
sp5ewx
|
My logger 32 has been hanging up for some time now for no reason. For example, I want to enter a new QSO or click on the rotor control. It stops responding and I can't close it even with Ctrl+Alt+Del. I need to restart my computer. Any suggestions??
sp5ewx
|
Fabian/EB1TR
Lorenzo IK0HFO