Re: Ride Report .....Bumpy
Drove to Knoxville and back yesterday. Traffic was god awful. I-40 is essentially a 2 lane road with interstate volume. It¡¯s going to be years before they can get it fixed.?
toggle quoted message
Show quoted text
On May 23, 2025, at 6:27?AM, Bill Kemper via groups.io <Bill3558@...> wrote:
?
Still beats driving.? Have a good trip Steve.?
On Thursday, May 22, 2025, 5:38 PM, Steve Murray via groups.io <n62km@...> wrote: Ride report for today - Hendersonville to Northern Alabama.? ?Very strong headwinds and bumpy, bumpy, bumpy.?
?
Lots of radio traffic reporting rough rides.? We stayed low to stay out of headwinds> 30 knots about 5K .? ?Seems like smooth rides were 9000 and above but that would have put us up against even stronger headwinds.
|
T-6 Aircraft at Hendersonville Airfield
---------- Forwarded message --------- From: Bill Kelder <bklkmiata96@...>Date: Thu, May 22, 2025 at 21:28 Subject: T-6 Aircraft at Hendersonville Airfield To: achel Shannon < racheldshannon76@...>, Christie Melear < cmelear@...>, < philoflyer@...>, Bob Gardner < gardnerr@...>, Chuck < cdt388@...>, Jean Toxen < jtoxen@...>, Peter Leonard < pete28731@...>, Rick Morey < rick.morey1@...>, Michael Cavanaugh < michael-cavanaugh@...>, Jeff Paul < jeff.paul19@...>, Paul L < pfl801bru@...>, Tim Bamford < sunbamf@...>, George Hamilton < georgehamilton@...>, Joy Kwapien < jrkwapien@...>, Gordon Ludwig < gordonludwig1940@...>, Colin Crader < cradercm@...>, Ryan Nelson < ryann228@...>, < tony.wavering@...>, Chris Rogaine < crow1fly@...>, MuseumBoard2023 < MuseumBoard2023@...>, KIMBERLY ALBRIGHT < ksinatc@...>, < deborahschafer@...>, George Heddy III < gheddy@...>, Bob Peck < robertpeck@...>, Dennis Dickerson < dickerson1066@...>, < chuckwarden@...>, Carl Young < carlyjr1993@...>, Maria Lamia < maria@...>, Bill Kemper < bill3558@...>, Edward SAUNIER < edwardsaunier@...>, < tifferrari@...>, Ullmer Dan < ulltronu@...>, Loren Schafer < schafer306@...> If anyone is interested this Saturday 5/24/25 between 9 and 10 am there will be two T-6 airplanes arriving at the Hendersonville Airfield. They will be here doing a fly over at a local veterans memorial service.
|
Re: Ride Report .....Bumpy
toggle quoted message
Show quoted text
On Thursday, May 22, 2025, 5:38 PM, Steve Murray via groups.io <n62km@...> wrote: Ride report for today - Hendersonville to Northern Alabama.? ?Very strong headwinds and bumpy, bumpy, bumpy.?
?
Lots of radio traffic reporting rough rides.? We stayed low to stay out of headwinds> 30 knots about 5K .? ?Seems like smooth rides were 9000 and above but that would have put us up against even stronger headwinds.
|
Re: Ride Report .....Bumpy
Without catering and a restroom onboard that could make for a long trip
Ride report for today - Hendersonville to Northern Alabama.? ?Very strong headwinds and bumpy, bumpy, bumpy.?
?
Lots of radio traffic reporting rough rides.? We stayed low to stay out of headwinds> 30 knots about 5K .? ?Seems like smooth rides were 9000 and above but that would have put us up against even stronger headwinds.
|
Ride report for today - Hendersonville to Northern Alabama.? ?Very strong headwinds and bumpy, bumpy, bumpy.?
?
Lots of radio traffic reporting rough rides.? We stayed low to stay out of headwinds> 30 knots about 5K .? ?Seems like smooth rides were 9000 and above but that would have put us up against even stronger headwinds.
|
Re: 2025 Fly-In and Open House
Dang, I always enjoyed flying into those events and picking up some faast points at the safety seminar.?
On Wednesday, May 21, 2025, 4:11 PM, Timothy Higgins via groups.io <timothyahiggins@...> wrote: ---------- Forwarded message --------- From: Poole, Jack <Jack.Poole@...>Date: Wed, May 21, 2025, 3:11?PM Subject: 2025 Fly-In and Open House To: Cc: Andy Porter < andy.porter@...>
Everyone,
?
I would like to make everyone aware our annual Fly-In and Open House will be on June 7 from 10:00 till 14:00. I am attaching a flier for you to share with any of your friends or pilots you think
may be interested in joining us or to share across your social media accounts.
Please come out for some comradery and a good BBQ sandwich. Our flier mentions a fuel discount of .25 per gallon but look to the sign at the temporary tower for the correct self-serve price.
We are also never too skilled to learn something new, please join us for the FAA Safety event in the terminal conference room at 11:00 for a safety refresher. As always, we have many people who know little to nothing about aviation but just love airplanes,
especially children. We can always use extra eyes on the ramp to keep everyone safe in an active airport environment as planes taxi in and out.
As a note, airplane rides will not be available at the Fly-In this year due to unforeseen circumstances from our provider. Helicopter rides will be available though.
?
Thank you for your continued support and participation in our airport community,
?
Jack
?
Jack E. Poole
Shelby-Cleveland County Regional Airport
830 College Avenue
Shelby, NC ?28152
?
?
|
2025 Fly-In and Open House
---------- Forwarded message --------- From: Poole, Jack <Jack.Poole@...>Date: Wed, May 21, 2025, 3:11?PM Subject: 2025 Fly-In and Open House To: Cc: Andy Porter < andy.porter@...>
Everyone,
?
I would like to make everyone aware our annual Fly-In and Open House will be on June 7 from 10:00 till 14:00. I am attaching a flier for you to share with any of your friends or pilots you think
may be interested in joining us or to share across your social media accounts.
Please come out for some comradery and a good BBQ sandwich. Our flier mentions a fuel discount of .25 per gallon but look to the sign at the temporary tower for the correct self-serve price.
We are also never too skilled to learn something new, please join us for the FAA Safety event in the terminal conference room at 11:00 for a safety refresher. As always, we have many people who know little to nothing about aviation but just love airplanes,
especially children. We can always use extra eyes on the ramp to keep everyone safe in an active airport environment as planes taxi in and out.
As a note, airplane rides will not be available at the Fly-In this year due to unforeseen circumstances from our provider. Helicopter rides will be available though.
?
Thank you for your continued support and participation in our airport community,
?
Jack
?
Jack E. Poole
Shelby-Cleveland County Regional Airport
830 College Avenue
Shelby, NC ?28152
?
?
|
Re: Looking for 200 Ohm Resisitor
Wiith so many Radio Shack fans coming out of the closet, I think the group has shown
Resistance is -- in fact -- NOT FUTILE! (had to, just had to).
Happy to help, Steve.
Dave E.
I have some 220 ohm Your welcome to have Darwin
On Sunday, May 18, 2025, 8:14 PM, Steve Murray via <n62km=[email protected]> wrote: Thanks David.? I will give the bundle of 4 a try.
?
Much appreciate the hangar delivery.
?
Steve
?
?
|
Re: Looking for 200 Ohm Resisitor
I have some 220 ohm Your welcome to have
On Sunday, May 18, 2025, 8:14 PM, Steve Murray via groups.io <n62km@...> wrote: Thanks David.? I will give the bundle of 4 a try.
?
Much appreciate the hangar delivery.
?
Steve
?
?
|
Re: Looking for 200 Ohm Resisitor
Thanks David.? I will give the bundle of 4 a try.
?
Much appreciate the hangar delivery.
?
Steve
?
?
|
Re: Looking for 200 Ohm Resisitor
That¡¯s one way to get our attention!
On Sun, May 18, 2025 at 14:41 David Erickson via <Davidgerickson66= [email protected]> wrote: Hi Steve,
After verifying no activity at your hangar, I 'violated' Alex's & Mark's for a moment to tape the resistors to their door jamb. [A&M's door has been checked locked.]
Hope you can make them work!
Dave
So far! On Sun, May 18, 2025 at 13:10 Jerry Marstall via <jerrylm1986= [email protected]> wrote: Did it work?
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
Hi Steve,
After verifying no activity at your hangar, I 'violated' Alex's & Mark's for a moment to tape the resistors to their door jamb. [A&M's door has been checked locked.]
Hope you can make them work!
Dave
So far! On Sun, May 18, 2025 at 13:10 Jerry Marstall via <jerrylm1986= [email protected]> wrote: Did it work?
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
Steve,
Sorry I just saw this. I have some if you still need them.?
Jerry?
toggle quoted message
Show quoted text
On May 18, 2025, at 2:09?PM, Alex Nelon via groups.io <Alex.nelon@...> wrote:
? So far! On Sun, May 18, 2025 at 13:10 Jerry Marstall via <jerrylm1986= [email protected]> wrote: Did it work?
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
<20250518_112846.jpg> <Screenshot_20250518-114612_Chrome.jpg> 190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
<20250518_105935.jpg> <20250518_112829.jpg> ![]() <Screenshot_20250518-112642_Chrome.jpg>
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
toggle quoted message
Show quoted text
On Sun, May 18, 2025 at 13:10 Jerry Marstall via <jerrylm1986= [email protected]> wrote: Did it work?
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
toggle quoted message
Show quoted text
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
203 ohms with four side-by-side. NICE when the theory works out IN PRACTICE!
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud. On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
I wish I understood electronics. I did wire a GFI plug yesterday and felt pretty proud.
On Sun, May 18, 2025 at 11:57 David Erickson via <Davidgerickson66= [email protected]> wrote: Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
![]()
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Re: Looking for 200 Ohm Resisitor
Happy Sunday, Steve,
All,
I'm fresh out of 200 ohm singles, lol, but have a solution, so long as you can accommodate a bit more volume with four small resistors configured in a bundle/close staggered "hug" vs. a single resistor:
Take this fresh pack of 820 ohm-ers (which I'll never use) and put four in parallel.? They're each rated at 1/2 watt, so you meet that power/heat dissipation requirement.? You'll end up with 205 ohms equivalent resistance, which gets you more precision (2.5%) compared to a typical, single resistor's tolerance of 5-10%,
190-210 ohms for your case at 5%.
Happy to solder them together for you so you have a "plug-and-play" single resistor equivalent to 205 ohms if you'd?like. Let me know! Dave
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
If you¡¯re out at the airfield today would you take up the folding ¡°X¡±s on Johnson Field? If you have a truck and can bring them to the Museum Hangar apron we¡¯ll put them away.
The only ropes that need to be left up are the ones from the corner of Mark¡¯s and my hangar to the old fuel shed. We¡¯ll string one from there to the SE corner of the Museum hangar apron. This is to prevent vehicular traffic on that area of the swamp so it can heal up a bit.
Thanks
Alex
|
Looking for 200 Ohm Resisitor
Anyone have a 200 ohm resistor, need one for hooking up VDO? fuel pressure sensor.? 1/4 watt (or less) will do as it is a signal line only.
?
Thanks
|
Alex Nelon
Timothy Higgins
Darwin Jones
