¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Re: Need HELP!!!!
I belive it is working. When the I2C Scan starts it finds the audio? hat and then scans a few seconds later and come back on devices found.? Is this correct on how the I2C Scan works, finds one
By Tom Schulte · #33317 ·
Re: 4SQRP T41 Assembled/Tested Radio for sale
I have received an offer to buy the T41 from K0ESE. I'll mark this as "Funds Pending". Thanks and 73, Frank K1FFJ
By Frank Jandreau · #33316 ·
More testing on PA
I have Dr. Bills PA and a similar (same finals) from 60dbm shop. Both on 13V same 0dB sweep from SA. I attached the 60dBm Schematic for reference. Here is Dr. Bills with 0dB in His with -10dB in,
By Tim · #33315 ·
Re: QRP-Labs
*** Yup. That being said, the QMX+ is back on the shelf, and I'm back to playing with the T41. Despite being a kit, the QMX is essentially an appliance - from my point of view. Because it's closed
By jerry-KF6VB · #33314 ·
Re: 4SQRP T41 Assembled/Tested Radio for sale
Sorry forgot the photo:
By Frank Jandreau · #33313 ·
4SQRP T41 Assembled/Tested Radio for sale
Hello everyone, I have an assembled, tested and calibrated a T41 from 4SQRP that I built as a comparison to my T41EP that I built from scratch (no kit). I wanted to see if my no kit T41 performed as
By Frank Jandreau · #33312 ·
Re: QRP-Labs
That's one thing Hans does right: He doesn't release stuff until he's convinced it's bullet-proof. He had an SSB rig at the 2018 (?) YOTA conference in Africa, so it's not like he hasn't been fooling
By jjpurdum · #33311 ·
Re: boards and kits and stuff
The schematic is attached to this comment: /g/SoftwareControlledHamRadio/message/33107
By Oliver KI3P · #33310 ·
Re: QRP-Labs
*** I guess that's why the radio has a built-in SWR bridge, and fairly fussy protection software. Since I'm operating it into my Tiny Linear, the radio is isolated from antenna SWR. Nobody hears me at
By jerry-KF6VB · #33309 ·
Re: QRP-Labs
*** It's a digital PA. In the schematic, the BS170's are fed RF by LOGIC gates. I think it's what's called a "class E". They don't even have heat sinks. They output 5W without breaking a sweat. The
By jerry-KF6VB · #33308 ·
Re: QRP-Labs
It is. They become extremely sensitive to load mismatches. The group is full of reports of them failing, especially when an external tuner is looking for a match. Dave
By Dave Mueller AA3EE · #33307 ·
Re: boards and kits and stuff
BillIs there a. Link to sch etc for this little board.?I don't have any issues with my build and a 6inch cable but then again, not checked the? higher bands.Glenn?'72 ISUZU BELLETT SPORTSent from
By Glenn · #33306 ·
Re: QRP-Labs
Did you get a chance to look at the spectrum? That seems like a lot of power for BS170s! -- 73 Greg KF5N
By Greg KF5N · #33305 ·
Re: Oscillations on high bands
Testing my 20W PA with -10dB in verses? 0dB in I see very little change in gain on lower bands 160-7, some gain on 10-17 and significant (3dB) gain on 28-50 Mhz. Max 0dB in is 160-80m is 12W,?
By Tim · #33304 ·
Re: Need HELP!!!!
to avoid misunderstandings: 3.3V are only on pin46 with teensy in! Teensy produce this 3.3V by himself! we have ?different rails with 3.3V!
By Ralph Lieber · #33303 ·
Re: Need HELP!!!!
if there is no 3.3V on Pin46, please check for short (without teensy) pin46 to ground! if there is a short you will destroy the (next) teensy if you (re)placed him!
By Ralph Lieber · #33302 ·
QRP-Labs
I was just browsing their website, and I noted that Hans has finally released beta SSB software for the QMX. Downloaded it, ran it...holy crap, it works! SSB is created by doing magic with the IQ
By jerry-KF6VB · #33301 ·
Display driver board
I sent out five of those new display driver boards about a week ago and only saw posted that Terrance got his working as was able to use a 3-foot long display cable without display-T41 errors/lockups.
By K9HZ · #33300 ·
Re: Need HELP!!!!
If no voltage on pin46 then the teensy socket or teensy itself is bad. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch ¨C K9ZC Staunton,
By K9HZ · #33299 ·
Re: Need HELP!!!!
D2 and D3 are illuminated? If so the power rails are working. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois
By K9HZ · #33298 ·