Keyboard Shortcuts
ctrl + shift + ? :
Show all keyboard shortcuts
ctrl + g :
Navigate to a group
ctrl + shift + f :
Find
ctrl + / :
Quick actions
esc to dismiss
Likes
Search
Re: powermax 1000 machine interface connector
|
Gents
toggle quoted message
Show quoted text
I bought a connector for the Powermax 1000 machine interface and have it installed. Just thought I'd pass on the part numbers that I used. Per my previous posting, I was not sure I had the proper part number for the plasma interface but now have them installed to the THC SENSOR card inside my Powermax. The mating (male pinned connector) seems to be an: Amp/Tyco 14 pin part 26044-1 or (DigiKey Part A1358-ND) Male pins( 5ea.) I used were: Amp/Tyco 66099-4 or (DigiKey Part A1340-ND) and will take 16-18awg wire The matching Size 17 cable clamp for the exiting wires is Amp/Tyco 206070-1 or (DigiKey Part A1332-ND) Should you need the existing connector: The square flanged Connector on the back of the Supply is Amp/Tyco 206043-1 or (Digi-Key Part A1362-ND) The female pins for this connector I have are Amp/Tyco 66101-4 or (Digi-Key Part A16080-ND) These pins are 30u Gold over 50u Nickel crimp style pins and sockets. I've uploaded 2 photos showing the connector I've added and The Connection to the THC sensor board that's mounted nearby inside the Supply. I hope they made it to the proper location. Brian ----- Original Message -----
From: JCullins To: mach1mach2cnc@... Cc: Bob Campbell ; tom@... Sent: Friday, April 07, 2006 8:42 AM Subject: Re: [mach1mach2cnc] Re: powermax 1000 machine interface connector Good idea Paul, Bob, Tom and I will pass that idea along to other customers. Jim ----- Original Message ----- From: paul_hvidston To: mach1mach2cnc@... Sent: Thursday, April 06, 2006 9:39 PM Subject: [mach1mach2cnc] Re: powermax 1000 machine interface connector Brian, That's the part number I landed on, but never bought one. I ended up going a different route. I mounted my THC300 sensor board inside there via its DB-9 connector on a plate machined to fit the original connector hole (completely reversible should it require service). BTW, To run a hand torch, all you need to do is add a jumper to the to the torch connector (cable-side) between pins 9 and 11 (need to add another connector pin). Maybe I'll purchase the machine torch someday... Regards, Paul H. --- In mach1mach2cnc@..., "Brian" <lhm332@...> wrote: > > Hi, > I have the Powermax1000-G3. Does anyone know what the circular > connector part number is for the machine interface? I'm looking for > just the plug end to bring out the THC start signal and torch switch > connections. > > So far I've found an AMP/TYCO 14 pin part# 206044-1 but I'm not sure > the keying of the shell is proper. > > Anyone know the proper part number? > > Thanks, > Brian > www.machsupport.com - Web site Access SPONSORED LINKS Craft hobby Hobby and craft supply Cnc controller Mach2 Machine controller ------------------------------------------------------------------------------ YAHOO! GROUPS LINKS a.. Visit your group "mach1mach2cnc" on the web. b.. To unsubscribe from this group, send an email to: mach1mach2cnc-unsubscribe@... c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. ------------------------------------------------------------------------------ This message has been processed by Firetrust Benign. www.machsupport.com - Web site Access ------------------------------------------------------------------------------ YAHOO! GROUPS LINKS a.. Visit your group "mach1mach2cnc" on the web. b.. To unsubscribe from this group, send an email to: mach1mach2cnc-unsubscribe@... c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. ------------------------------------------------------------------------------ |
to navigate to use esc to dismiss