Sure, that will work also. It is my son's address
since we traded homes with him.
?
Thanks and 73,
Tony KB9YIG
?
toggle quoted message
Show quoted text
----- Original Message -----
Sent: Monday, November 07, 2005 5:55
PM
Subject: Re: [softrock40] SoftRock v5.0
kits may soon be ordered
Tony,
?
I sent my check to the address listed in QRZ.com (1447 E 750N)? Will
you get that check okay?
?
73 - Mike - K9JRI
Sure, that would be fine.? My address
is:
?
Tony Parks KB9YIG
1344 E 750 N
Springport, IN 47386
----- Original Message -----
Sent: Monday, November 07, 2005 4:50
PM
Subject: Re: [softrock40] SoftRock
v5.0 kits may soon be ordered
Also, I don't have PayPal. May I pay by Cashier's
Check?
Bill
KA0VXK
----- Original Message -----
Sent: Monday, November 07, 2005
14:07 PM
Subject: Re: [softrock40] SoftRock
v5.0 kits may soon be ordered
Hi Bill,
?
The UCB is for use with the SDR-1000 and
provides expanded external I/O.? Not needed in
general.
?
73,
Tony KB9YIG
?
----- Original Message -----
Sent: Monday, November 07, 2005
2:57 PM
Subject: Re: [softrock40]
SoftRock v5.0 kits may soon be ordered
I did not see a cost for the Universal Control
Board. This is a first time order.
Do I need one?
Sri abt the ignorance.
Bill
KA0VXK
----- Original Message -----
Sent: Sunday, November 06, 2005
21:20 PM
Subject: Re: [softrock40]
SoftRock v5.0 kits may soon be ordered
Hi Art,
I have all the parts for the alpha
kit ready to send except for the toroid
cores.? I was
informed they were shipped last Monday from Florida, so I am
kind of wondering if it is really so.? I have held off on
sending the alpha
kits until I had the cores in hand, but may
need to reorder the cores from
some other source.
So far
three of the alpha kits have been built (with the few toroids I had)
and are working very nicely.? Performance has looked good
enough to head for
a kit run at the end of
November.
Sorry for the delay on getting the alpha kits
out.
73,
Tony KB9YIG
----- Original Message -----
From: "KY1K"
To:
Sent: Sunday, November 06,
2005 10:11 PM
Subject: Re: [softrock40] SoftRock v5.0 kits may
soon be ordered
> Hi Tony,
>
> Did the
alpha test plans fall through???
>
> Should I go ahead
and order 2 kits, or will the alpha test kit arrive
> soon? So
far nothing.......
>
> Hope everything is
OK.
>
> Regards,
>
>
Art
>
>
> At 09:18 PM 11/6/2005, you
wrote:
>
>>Good Evening
All,
>>
>>After a number of tests with the new
v5.0 SoftRock I have deceided
>>it is ready for kit
production.? Orders may be placed as soon as
the
>>ordering system is setup at Dale's (WA8SRA) HamSDR
website
>>(
Kit deliveries will start at the
>>end of this
month.
>>
>>Three kits will be offered as
follows:
>>
>>1) SoftRock v5.0 QSD kit at $19 per
kit (US/Canada, $20 for DX).
>>This is the lower board in
the two board stack and contains the 5
>>VDC regulator, two
voltage comparators, the QSD quad switch, and the
>>dual
low-noise audio amplifier.? All components to build the
board
>>will be provided in this kit and also a stereo
audio cable will be
>>included.? However, no RG174
coax cable or the BNC connector will be
>>provided in the
kit. (400 kits are planned)
>>
>>2) SoftRock v5.0
Low Band OSC/BPF kit at $7.50 per kit (US/Canada,
>>$8.50
for DX).? This is the upper board in the two board stack
and
>>contains the oscillator circuit, the quadrature clock
phase shift
>>network and the BPF.? The fundamental
frequency xtal will not be
>>included in the kit but
components will be provided for use over the
>>bands from
80 meters to 30 meters. (750 kits are
planned)
>>
>>3) SoftRock v5.0 High Band OSC/BPF
kit at $7.50 per kit (US/Canada,
>>$8.50 for DX).?
This is again the upper board and contains the
>>components
for use of the SoftRock at 20 meters and above.?
(250
>>kits are planned. Good operation at 20 meters has
been demonstrated
>>but operation at bands avove 20 meters
has not been done at
this
>>date.)
>>
>>When the ordering
system is in place, I will post on the Yahoo
>>group.
Please enter your order and confirm your order
information
>>before sending any payment.? Preferred
payment methode will be by
>>PayPal at user
raparks@... .
>>
>>Thanks and
73,
>>Tony Parks
KB9YIG
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>Yahoo!
Groups
Links
>>
>>
>>
>>
>
>
>
>
>
>
Yahoo! Groups Links
>
>
>
>
>
>
YAHOO! GROUPS LINKS
- ?Visit your group "" on the
web.
?
- ?To unsubscribe from this group, send an email
to:
?softrock40-unsubscribe@...
?
- ?Your use of Yahoo! Groups is subject to the .
