Bob,
Been there and done that!? I use a probing function on a fixed tool
pad that has +5V on it and a ground clip on the tool to make sure we have
a good contact.? The touch pad is on G53 and I have managed to make
tool offsets work in Turbocnc.? I believe others have done it in
Mach and other controllers.? Another way to do it is to have a
dedicated area on your blank pcb and use the electrical method to touch
off and not worry about fixture offsets.?
In this case, use a probe function and call a G92 Z0 at the probe.?
Raise the tool to clear everything and forge on.
Country
?At 3/21/2019 04:52 PM, bownes wrote:
toggle quoted message
Show quoted text
Probably starting a religious
war, but I've actually had better luck with engraving bits that actual
mills for traces. I change over to a real mill for milling operations.
What I really need to do is master gcode well enough to have a routine
that re-zero's the height after changing a bit.
Bob
On Thu, Mar 21, 2019 at 4:26 PM John Ferguson via Groups.Io
<jferg977=[email protected]>
wrote:
- I suppose swarf isn't the best word, but I'm curious about how you
guys get rid of the chips which lodge in cuts.?? I've been chasing
them out with a needle, buy it's tedious.
- I've got 90 psi air in the shop. Maybe I should try that.
- I've got my production system running very smoothly. Design In Eagle,
generate Gcode in pcpcode, sometimes include autocad millwork with gcode
generated in SheetCAM, set up work piece, set height on cutter and
go.
- I make all of my boards from 2.5x4.0 workpieces. I made an aluminum
fixture with a depression which fist these workpieces and has a lid which
locates 4 holes one in each corner.?? I drill the holes and then
screw the board down to an HDPE fixture bolted to the table on my 6040
router.?? The HDPE has 4 holes which take 6-32 nylon socket head
caps screws.?? I face off the surface the board sits on every 4th or
5th board to maintain level.??
- I adjust the bit height by rolling a piece of .250 drill rod back and
forth until the bit just clears and then dropping it one click on the
servo so it doesn't quite clear.?? I have vertical "home"
set at Z=1.000 on the machine so I have to raise the spindle .750 before
I start.?? I suppose I could lower the home to .250 and eliminate
the "raise" but having it at one inch gives me enough time to
catch some kinds of screw-ups.
- I've been delighted with this bit. I buy them from Precise Bits and
they seem to last pretty well.??
- EM3E8-0100-15V 0.0100in. (0.254mm) tip dia., 3-flute 15?¡ã tapered
stub trace-isolation bit, 0.020 in. DOC, 1.42 in. (36mm) OAL 2 $16.95
$33.90
- The size of the bur on the edge of cuts seems to increase as they
wear out, but only downside of this seems to be more dressing of the
finished board. I use 400 grit paper and final clean up with 800 crocus
cloth.
- I've been tinning the finished boards with MG Chemical 421.??
I'm a bit mystified why I get better tinning if i rough up the board with
400 grit before plating it.?? I wash board with acetone before
tinning.
- After I've soldered everything (all through hole - no smds yet), I go
over the board with a loupe and remove any shorts with braid and clean
out any suspicious cuts with a needle.
- and they always work, at least the ones I haven't messed up the
circuits on.
- If you read this and see anything stupid, let me know.?? Also
I'm still like a better way to get rid of chips.
- regards,
- John ferguson?? delray beach
