开云体育

I saw this video online and decided it wasn't half bad. So, I am going to do one of these for my remote and have NodeRed be able to handle it if I am not on the air. https://vimeo.com/133917999 Mike va3mw

The following files have been uploaded to the Files area of the [email protected] group. /wo2x flows/wo2x_NodeRedAndFRStackScreenshots.zip By: David De Coons wo2x Description: Updated screenshots of my Node Red and FRStack deployment on a Raspberry Pi 4

The following files have been uploaded to the Files area of the [email protected] group. //wo2x flows/NodeRed_FRStackScreenshots.zip By: David De Coons wo2x Description: Screenshots of Node Red and FRStack dashboards.

The following files have been uploaded to the Files area of the [email protected] group. /freq to band.json By: Alan Blind Description: Andreas' Frequency to Band function, added to a Node-Red Node, adjusted to work with Dave's Flex API VFO frequency output.

Andrew Mitchell added folder VA3CW

The following files have been uploaded to the Files area of the [email protected] group. /PG-XL flows-13.json By: Alan Blind Description: Updated PG-XL Flow with some more status outputs working now. Still WIP

OK, Mike, you said it was OK. I have uploaded my PG-XL Node-Red Flow. It is "ugly", but it works, mostly, for what I need. I received my PG-XL yesterday and learned that when I use my Node-Red Dashboard "Tune Button" the PG-XL stays in "operate", so I get many watts when tuning that way. This is not a problem when using any of the devices that Flex has interfaced with the PG-XL to because there is a "handy" button available to easily change the mode of the amp. So....I "Sharked" the PG-XL, found the commands and responses, and with the help of the "parsing wizard of Jersy", built an "Amp Mode" button. I then tied the "amp mode button" into my "Tune" button, so when I tune, from the Node-Red dashboard, the amp goes to "standby". I added an additional 50ms (80ms total) to the PTT delay on the Flex PTT settings for good measure to make sure the Node-Red commands were complete before RF goes out the pipe. The tune button background changes based on the status response from the PG-XL to confirm there was an actual mode change. Using the status also provides the data for the button to "toggle" between "Operate" and "Standby". The rest of the flow was an attempt to extract the remaining status messages from the PG-XL. As you will see, some make sense, like "band" and "VAC", others do not......like I said, WIP. Alan WA9WUD

Hi. Name is Charlie KB8CR. I am new to Node-Red, but have some experience with Raspberry Pi. Equipment here is a Flex 6400, a Flex 3000, and an Icom 7100. (all in a rack cabinet in the basement below the study (shack) I use a KMTronics Web relay (8 port) which does the following from its web interface: -Turn 6400 on/off (soft on/off from RCA jack on back) -Turn 3000 on/off (hard relay switching) -Switches another relay board to switch antenna (coaxial relay) from 6400 to 3000, Switches local Speaker output from 6400->3000, and local PTT from 6400->3000 -Turns power to 7100 on/off (it is on a separate HF antenna system) -Switches VHF/UHF antenna (coaxial relay) between 7100 and a scanner. The 6400 is usually controlled by a i5 Lenovo Mini PC (Win10-64bit), and the 3000 by a MacMini i5 running Win10-64bit because it has a firewire port for the 3000. Both computers are used headless via VNC. What I would like to do is have a 'dashboard' that controls the KMtronic relays, displays the Power, SWR, and Temps of the 6400 (and 3000 if that's possible) Future items would be to control a KPA500 amplifier, and perhaps a KAT500 tuner. (right now antennas are tuned by SGC tuners mounted at the feedpoints of the antennas. Remote audio and CW keying for the 3000 is done with Remoterig boxes from Sweeden. Are there tutorial videos anywhere?.....or are there 'pre-done' modules for the 6400 or 3000 (or that KMtronic relay boar) here (or somewhere)? Thanks, de Charlie KB8CR

The following files have been uploaded to the Files area of the [email protected] group. /Wd9gym.json By: Marty Boroff Description: Flows for a Flex 6600 in Mundelein. Rem O/Off, Disconnect/Connect antenna and Tuner

Hey all Just a thought, as I think this all the time. I get my flows running, but then I am embarrassed to post some of them since, well,then are a work in progress and a mess. Then, I get embarrassed. I want to encourage everyone not to worry about this. Posted flows will not be judged, but learned from and if you want to clean up someone's flow, excellent. No judgment of course. We all learn from them. Ask questions. There is no stupid question. I would like to encourage the sharing and mentoring of others (you don't want to see my Java--all my code is from Andreas, just hacked to work :) ). And, if someone provides feedback, please consider it a teaching moment. We all started at getting our first On/Off button to work and look like we want. And, how exciting that was. Carry on... as you were! 73, mike va3mw

Hi All (having just got off the phone with Tim) If your radio is doing weird things, before you open a support case, please make sure that NodeRed or some other external software is not causing the problem. This can be the following programs (but not limited to) FRStack SliceMaster NodeRed HRD Logbooks with CAT control VOX and loud dogs etc.. Thanks for help! :) Mike va3mw