开云体育

Larry,

downloaded, installed. I am running overtime, but wanted to get this far. I have to go now and will be out all day tomorrow. Finish getting this done on Wednesday. You do not know how much I appreciate you sticking with me. Sorry i was so dense. If you will, please look at the home page of httm://n5se.us. You might enjoy reading it.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 18:49
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Yes. Download the file that starts with stsw_.... As I mentioned earlier and follow the instructions in the beginner's guide for installation.


On Mon., 13 Dec. 2021 at 7:46 p.m., N5SE<bwmoore@...> wrote:
Larry
Is "DfuSe_Demo_V3.0.6_Setup" what I am after?


________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 18:35
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

/g/nanovna-users/message/11905
Go to the Google drive


On Mon., 13 Dec. 2021 at 7:26 p.m., N5SE<bwmoore@...> wrote: Larry Rothman,

I have downloaded Absolute_Beginner_Guide_NanoVNA_v1_5 and Absolute_Beginner_Guide_NanoVNA_v1_6. Speed read both and went back and read relative parts in detail. Larry, I truly do appreciate your help. I have to ask you, have you followed the trail from that sentence to the end. if you have and found that download, then please give me the specific URL. If not, do so and read the endless pdf files I have downloaded. Nobody has given me a specific URL, just references that take me nowhere. If you know where the needed downloads are, I beg you please copy the exact specific URL's from the top line of your browser and post them for me along with the specific download name. It cannot be that hard can it? If it is that hard, please explain, I cannot understand.

And I truly do appreciate your trying to help.

I always close my messages with 30, the historic traditional signal for end of traffic.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 17:56
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano


On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote: Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

[cid:3ab1f1b3-1535-4e5c-b030-fa9a5b13d2ef][Billy Wayne Moore]

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 18:49
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Yes. Download the file that starts with stsw_.... As I mentioned earlier and follow the instructions in the beginner's guide for installation.


On Mon., 13 Dec. 2021 at 7:46 p.m., N5SE<bwmoore@...> wrote:
Larry
Is "DfuSe_Demo_V3.0.6_Setup" what I am after?


________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 18:35
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

/g/nanovna-users/message/11905
Go to the Google drive


On Mon., 13 Dec. 2021 at 7:26 p.m., N5SE<bwmoore@...> wrote: Larry Rothman,

I have downloaded Absolute_Beginner_Guide_NanoVNA_v1_5 and Absolute_Beginner_Guide_NanoVNA_v1_6. Speed read both and went back and read relative parts in detail. Larry, I truly do appreciate your help. I have to ask you, have you followed the trail from that sentence to the end. if you have and found that download, then please give me the specific URL. If not, do so and read the endless pdf files I have downloaded. Nobody has given me a specific URL, just references that take me nowhere. If you know where the needed downloads are, I beg you please copy the exact specific URL's from the top line of your browser and post them for me along with the specific download name. It cannot be that hard can it? If it is that hard, please explain, I cannot understand.

And I truly do appreciate your trying to help.

I always close my messages with 30, the historic traditional signal for end of traffic.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 17:56
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano


On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote: Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

Yes.? Download the file that starts with stsw_.... As I mentioned earlier and follow the instructions in the beginner's guide for installation.

Larry
Is "DfuSe_Demo_V3.0.6_Setup" what I am after?


________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 18:35
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

/g/nanovna-users/message/11905
Go to the Google drive


On Mon., 13 Dec. 2021 at 7:26 p.m., N5SE<bwmoore@...> wrote: Larry Rothman,

I have downloaded Absolute_Beginner_Guide_NanoVNA_v1_5 and Absolute_Beginner_Guide_NanoVNA_v1_6. Speed read both and went back and read relative parts in detail. Larry, I truly do appreciate your help. I have to ask you, have you followed the trail from that sentence to the end. if you have and found that download, then please give me the specific URL. If not, do so and read the endless pdf files I have downloaded. Nobody has given me a specific URL, just references that take me nowhere. If you know where the needed downloads are, I beg you please copy the exact specific URL's from the top line of your browser and post them for me along with the specific download name. It cannot be that hard can it? If it is that hard, please explain, I cannot understand.

And I truly do appreciate your trying to help.

I always close my messages with 30, the historic traditional signal for end of traffic.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 17:56
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano


On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote: Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

/g/nanovna-users/message/11905?
Go to the Google drive


On Mon., 13 Dec. 2021 at 7:26 p.m., N5SE<bwmoore@...> wrote: Larry Rothman,

I have downloaded Absolute_Beginner_Guide_NanoVNA_v1_5 and Absolute_Beginner_Guide_NanoVNA_v1_6. Speed read both and went back and read relative parts in detail. Larry, I truly do appreciate your help. I have to ask you, have you followed the trail from that sentence to the end. if you have and found that download, then please give me the specific URL. If not, do so and read the endless pdf files I have downloaded. Nobody has given me a specific URL, just references that take me nowhere. If you know where the needed downloads are, I beg you please copy the exact specific URL's from the top line of your browser and post them for me along with the specific download name. It cannot be that hard can it? If it is that hard, please explain, I cannot understand.

And I truly do appreciate your trying to help.

I always close my messages with 30, the historic traditional signal for end of traffic.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 17:56
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano


? On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote:? Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

Larry Rothman,

I have downloaded Absolute_Beginner_Guide_NanoVNA_v1_5 and Absolute_Beginner_Guide_NanoVNA_v1_6. Speed read both and went back and read relative parts in detail. Larry, I truly do appreciate your help. I have to ask you, have you followed the trail from that sentence to the end. if you have and found that download, then please give me the specific URL. If not, do so and read the endless pdf files I have downloaded. Nobody has given me a specific URL, just references that take me nowhere. If you know where the needed downloads are, I beg you please copy the exact specific URL's from the top line of your browser and post them for me along with the specific download name. It cannot be that hard can it? If it is that hard, please explain, I cannot understand.

And I truly do appreciate your trying to help.

I always close my messages with 30, the historic traditional signal for end of traffic.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 17:56
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano


On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote: Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

Thank you Dragan. I think it would be unwise to buy from a China seller now. It would take weeks if at all, arriving. It might even ROT sitting on a cargo ship outside California.

Regards,
Jerry

Please go to the file section of the forum and download a copy of the complete beginners guide to the Nano?


On Mon., 13 Dec. 2021 at 1:18 p.m., N5SE<bwmoore@...> wrote: Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

The line in the wiki that's says wait for 10 seconds has a clickable link in it please look at it again.The M was a typo. Click on the word: utility? ?in that sentence.?


On Mon., 13 Dec. 2021 at 4:05 p.m., N5SE<bwmoore@...> wrote: Larry,

Thanks for the quick answer. I go to the WIKI and search for "Defuse Utility". I get:

"Search Results
Home
Here's another reference to the DeFuse utility - no registration req'd Installing and troubleshooting Installing the STM32 Virtual COM port drivers: (Refer to forum message 218)
Updated: 11:20am"

These results are clickable, so click on them and go right back to the WIKI page I was on.? So I try other searches. Same circle results; like a merry-go-round.

On your message, you say :

"Refer to the Wiki here: M Here's another reference to the DeFuse utility - no registration req'd
There is a link to a google drive with the drivers as well as the DeFuse utility. Download the file beginning with STSW... and install the software." I cannot find any of this or anything like it. What does the Capital M mean?

Just searching with FireFox (not in the WIKI)? I found several references to put the nanovna into DFU Mode. So far, I have not found a single reference that shows how to put a nanovna into the DFU mode (what ever that is).

So sorry I am so ignorant, but all of this seems so unorganized and piecemeal. Is there a URL and exact name for each thing I need to download?

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 13:00
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Hi Bill - welcome to the forum.
You need to install 2 drivers - one for the USB to serial bridge for a normal connection of the Nano to the PC and the other is the DFU driver.
Refer to the Wiki here: M Here's another reference to the DeFuse utility - no registration req'd
There is a link to a google drive with the drivers as well as the DeFuse utility. Download the file beginning with STSW... and install the software.
Then, turn on your Nanovna & connect to your to the PC and wait for it to recognize it. If you have a problem - check out the driver troubleshooting links in the Wiki for more info.


? ? On Monday, December 13, 2021, 01:18:00 p.m. EST, N5SE <bwmoore@...> wrote:

Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

Chris Gardner,

Searched that url from one end to the other. All you can get is pdf's (multiple) telling you how great it is going to be. No other downloads.

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Chris Gardner via groups.io <seaman98@...>
Sent: Monday, December 13, 2021 17:15
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Billy, Try this url

Billy, Try this url

You can try this:

I got this one:
Just search for HDD case on Ali, Ebay etc ...

Greetings to the Group.

I just purchased a NanoVNA-H4 and I am unable to find a hard or soft case for this size/configuration. Any suggestions will be appreciated.
Thank you.

Larry,

Thanks for the quick answer. I go to the WIKI and search for "Defuse Utility". I get:

"Search Results
Home
Here's another reference to the DeFuse utility - no registration req'd Installing and troubleshooting Installing the STM32 Virtual COM port drivers: (Refer to forum message 218)
Updated: 11:20am"

These results are clickable, so click on them and go right back to the WIKI page I was on. So I try other searches. Same circle results; like a merry-go-round.

On your message, you say :

"Refer to the Wiki here: M Here's another reference to the DeFuse utility - no registration req'd
There is a link to a google drive with the drivers as well as the DeFuse utility. Download the file beginning with STSW... and install the software." I cannot find any of this or anything like it. What does the Capital M mean?

Just searching with FireFox (not in the WIKI) I found several references to put the nanovna into DFU Mode. So far, I have not found a single reference that shows how to put a nanovna into the DFU mode (what ever that is).

So sorry I am so ignorant, but all of this seems so unorganized and piecemeal. Is there a URL and exact name for each thing I need to download?

30, Billy

________________________________
From: [email protected] <[email protected]> on behalf of Larry Rothman via groups.io <nlroth@...>
Sent: Monday, December 13, 2021 13:00
To: [email protected] <[email protected]>
Subject: Re: [nanovna-users] Confused Newbie

Hi Bill - welcome to the forum.
You need to install 2 drivers - one for the USB to serial bridge for a normal connection of the Nano to the PC and the other is the DFU driver.
Refer to the Wiki here: M Here's another reference to the DeFuse utility - no registration req'd
There is a link to a google drive with the drivers as well as the DeFuse utility. Download the file beginning with STSW... and install the software.
Then, turn on your Nanovna & connect to your to the PC and wait for it to recognize it. If you have a problem - check out the driver troubleshooting links in the Wiki for more info.


On Monday, December 13, 2021, 01:18:00 p.m. EST, N5SE <bwmoore@...> wrote:

Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

Hi Bill - welcome to the forum.
You need to install 2 drivers - one for the USB to serial bridge for a normal connection of the Nano to the PC and the other is the DFU driver.
Refer to the Wiki here: M Here's another reference to the DeFuse utility - no registration req'd
There is a link to a google drive with the drivers as well as the DeFuse utility. Download the file beginning with STSW... and install the software.
Then, turn on your Nanovna & connect to your to the PC and wait for it to recognize it. If you have a problem - check out the driver troubleshooting links in the Wiki for more info.

Hello Nanovna Users,

I have just joined the group and this is my first post. I am backwoods born and raised; a ranch hand until I graduated from High School. Simply put, I am confused like the little boy who dropped his Chicken Gum in the Chewing Yard.

I have a Nanovna-H V3.4 with the 5351 chip. I have Putty Release 0.76 on my PC which is running Windows 7. I want to get my nanovna connected to my PC, so I went to the WIKI (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) where I found the link (/g/nanovna-users/wiki#But-first---connecting-to-a-PC) to STM32 COM port drivers. This is apparently a dead link.

In the meantime, I have tried to using Putty to connect to the nanovna and cannot find it.

Any help or suggestions will be appreciated. Thanks in advance.

30, Billy

[Billy Wayne Moore]

OK, I understand but you still have not answered one question: Can you talk to your H4 through Terraterm or putty?
Please install this version of firmware for your H4:
/g/nanovna-users/files/Dislord%27s%20Nanovna%20-H%20Firmware/NanoVNA%20v1.0.69%20fw%20pack.zip
Unzip and ONLY use the _H4_ DFU file.
Verify you can talk to the command console through a terminal program on your PC before trying to use any of the Nano PC apps.

On Mon, Dec 13, 2021 at 02:56 PM, Larry Rothman wrote:

you have not said what model of Nano you have.
Are you able to talk to the Nano through a termial program like Teraterm or
Putty when it is connected to the PC?
If not, you need to troubleshoot that first.

I started this topic and I said I have a Nanovna-H4. W10 64 bits
All this does not happen with the original firmware v0.5.0.
I do the tests that you tell me and I answer.
Thanks /Antonio EA7HJ

Antonio,
you have not said what model of Nano you have.
Are you able to talk to the Nano through a termial program like Teraterm or Putty when it is connected to the PC?
If not, you need to troubleshoot that first.