Re: How about using a USB memory stick instead of an SD card
#features
Thank you for the speedy responses. I will read the guide as you suggest.?Of course, using a terminal emulator over the attached com port makes sense.?Admittedly, I haven't had occasion to use that method of conversing with attached?hardware in quite a while. Thank you for an outstanding and very informative group.
toggle quoted message
Show quoted text
On Thursday, December 9, 2021, 04:45:25 PM EST, Donald S Brant Jr <dsbrantjr@...> wrote:
Or you could pop out the SD card and put it into a card reader, the old "Sneakernet" way.? 73, Don N2VGU
|
I think you are mixing "ch1" with the memory save slots. But answering
your questions, assuming you were referring to the save slots:
a) The save slots store a calibration (and various other parameters like
trace setup, etc) until you overwrite them with a new 'save' to that same
slot.
b) Recalling a saved slot (0-3) restores whatever you previously saved
there, no matter how many times you have done the cal reset.
c) it is necessary to do cal - reset every time before you calibrate.
Doing so clears the currently loaded calibration (from power-on or the last
memory recall).
d) after cal - reset, then doing a cal as you suggest for whatever range,
then that cal becomes active but not saved - it will be there only until
you turn off the device, unless you do a save.
So yes, the save slots are there to save your presets - which will include
whatever trace setups, etc. you did before the save.
And yes, you can start with recalling a saved slot, then re-cal to zoom in
or whatever, and it will use that new cal until you do another cal or
recall a saved cal again.
toggle quoted message
Show quoted text
On Thu, Dec 9, 2021 at 1:17 PM <Neil2Com@...> wrote: ill add a cal Q on top of the good answers already said...
Q: say i cal 2m up to 440 in ch0
then cal hf 1mhz to 50 in ch1
then cal 28mhz in ch2
finally cal my cb/27 in ch3
if i go back and sitting on C0, hit reset a cpl times and do a re-cal on 0
for just the 144/2m only, is my 2 or 3 other calibrations ch1, 2, 3, still
good and valid.. or would i need to go back and redo those? ie. re-cal is
channel specific, or makes all others not as good as before? if that makes
since??
im getting it to where i want it preset for a few options but just change
say ch0 for doing a different sweep for different random tests and go back
to have it monitor the basics? ch1, 2, 3....????
|
Re: How about using a USB memory stick instead of an SD card
#features
Or you could pop out the SD card and put it into a card reader, the old "Sneakernet" way. 73, Don N2VGU
|
If you use SAVER, you can store cals on your PC or laptop supporting
SAVER. If properly labeled, it's clear specifically what cal. you are
pulling up for which application.
Dave - W?LEV
toggle quoted message
Show quoted text
On Thu, Dec 9, 2021 at 9:17 PM <Neil2Com@...> wrote: ill add a cal Q on top of the good answers already said...
Q: say i cal 2m up to 440 in ch0
then cal hf 1mhz to 50 in ch1
then cal 28mhz in ch2
finally cal my cb/27 in ch3
if i go back and sitting on C0, hit reset a cpl times and do a re-cal on 0
for just the 144/2m only, is my 2 or 3 other calibrations ch1, 2, 3, still
good and valid.. or would i need to go back and redo those? ie. re-cal is
channel specific, or makes all others not as good as before? if that makes
since??
im getting it to where i want it preset for a few options but just change
say ch0 for doing a different sweep for different random tests and go back
to have it monitor the basics? ch1, 2, 3....????
--
*Dave - W?LEV*
*Just Let Darwin Work*
|
ill add a cal Q on top of the good answers already said...
Q: say i cal 2m up to 440 in ch0
then cal hf 1mhz to 50 in ch1
then cal 28mhz in ch2
finally cal my cb/27 in ch3
if i go back and sitting on C0, hit reset a cpl times and do a re-cal on 0 for just the 144/2m only, is my 2 or 3 other calibrations ch1, 2, 3, still good and valid.. or would i need to go back and redo those? ie. re-cal is channel specific, or makes all others not as good as before? if that makes since??
im getting it to where i want it preset for a few options but just change say ch0 for doing a different sweep for different random tests and go back to have it monitor the basics? ch1, 2, 3....????
|
Re: How about using a USB memory stick instead of an SD card
#features
Chris, You need to have the last formally released version of DiSlord's firmware installed in your H or H4 for the 3 SD card commands to work. That should be 1.0.69 You can find in in an zip'ed file at /g/nanovna-users/files/Dislord's%20Nanovna%20-H%20Firmware Install the firmware, connect your Nano to your PC/Mac/*nix box and talk to it using a terminal emulator application. Read my Console Commands document also in the files section to see what commands you can run remotely from the terminal window. (it hasn't been updated in 2 years but it has most of the info you'll need. Also - please read the Beginners userguide, also in the files section and look through the forum Wiki for info. Regards, Larry
On Thursday, December 9, 2021, 01:14:34 p.m. EST, Chris Gardner via groups.io <seaman98@...> wrote:
Greetings, Thank you for that information. But, I am not clear as to how to initiate an connection to,?and or the ability to exchange data to and from the SD Card which is installed into the NanoVna_H4?which I have. I did not notice any change of the device screen indicating a connection was now possible.?Also, I didn't notice any fields located in NanoVNA-saver application on my windows 10 PC. Must I install,?or re-install device firmware in order to affect the change that I have made by accessing the card slot.?Thank You
? ? On Thursday, December 9, 2021, 10:59:54 AM EST, DiSlord <dislordlive@...> wrote:?
My NanoVNA? H/H4 fw support commands for SD card access, so some one can write software for work.
sd_list {pattern}
sd_read {filename}
sd_delete {filename}
Commands:
sd_list {pattern}
example get all files list
sd_list
or
sd_list *.*
Read s1p list
sd_list *.s1p
Read bmp list
sd_list *.bmp
Read s1p and s2p list
sd_list *.s?p
Read *.bin list
sd_list *.bin
Log {filename} {size}
18.238 rx: ch>
18.241 tx: sd_list *.bmp
18.243 rx: sd_list *.bmp
18.246 rx: sd_list:
18.250 rx: VNA_000004.bmp 153670
18.253 rx: VNA_00000C.bmp 153670
18.256 rx: VNA_210721_210606.bmp 307270
18.258 rx: VNA_000077.bmp 153670
18.261 rx: VNA_000114_212649.bmp 307322
18.300 rx: VNA_000119_233142.bmp 307322
18.303 rx: VNA_000119_233204.bmp 307322
18.306 rx: VNA_000119_233223.bmp 307322
18.309 rx: VNA_000122_082125.bmp 307322
18.312 rx: VNA_000129_085002.bmp 307322
18.315 rx: VNA_000129_085132.bmp 307322
18.318 rx: VNA_000129_085345.bmp 307322
18.321 rx: VNA_000129_085607.bmp 307322
18.323 rx: VNA_000129_091616.bmp 307322
18.326 rx: VNA_000129_091818.bmp 307322
18.361 rx: VNA_000301_213820.bmp 307322
18.364 rx: VNA_201129_081345.bmp 307322
18.368 rx: VNA_201129_081351.bmp 307322
18.371 rx: VNA_201129_081357.bmp 307322
18.374 rx: ch>
For read file need
sd_read {filename}
After nano return binary file data
or on error
"err: no file\r\n"
Delete file:
sd_delete {filename}
After nano delete it from SD card:
Output
shell_printf("delete: %s %s\r\n", filename, res == FR_OK ? "OK" : "err");
|
Re: How about using a USB memory stick instead of an SD card
#features
On 12/9/21 10:14 AM, Chris Gardner via groups.io wrote: Greetings, Thank you for that information. But, I am not clear as to how to initiate an connection to,?and or the ability to exchange data to and from the SD Card which is installed into the NanoVna_H4?which I have. I did not notice any change of the device screen indicating a connection was now possible.?Also, I didn't notice any fields located in NanoVNA-saver application on my windows 10 PC. Must I install,?or re-install device firmware in order to affect the change that I have made by accessing the card slot.?Thank You
The NanoVNA has two "interfaces" - one is the touch screen, the other is the serial port over USB.? So there's lots of functions available by sending serial commands and getting responses back (as DiSLord illustrated) that aren't available from the touch screen. NanoVNA-Saver probably hasn't been updated to incorporate this new functionality.
|
Re: How about using a USB memory stick instead of an SD card
#features
Any NanoVNA can control from CPU
Software like NanoVna Saver or NanoVNA-App open com port connection and send commands
You or any programmer can update exist / write new software for SD card access
Just use this commands
At this moment this software not exist, but I hope there is an author who implements this option
|
Advice: When in doubt, calibrate.......
Besides, the whole cal. procedure is relatively insignificant in time.
Even using the HP 8753C, I calibrate every time I want to measure my latest
"brain fart".
Dave - W?LEV
Dave - W?LEV
toggle quoted message
Show quoted text
On Thu, Dec 9, 2021 at 2:41 PM Joe WB9SBD <nss@...> wrote: When you do a Calirate say between 3.5 and 4 Mhz, and save it.
Now next time you power the unit up (NanoVNA-H4)
And choose that saved profile, is that calibration still valid?
Or should you do it every time you power the unit up?
AND
OK again say you calibrate it between 7.0 and 7.3 Mhz. and save it to
another slot.
Now between 7.0 and 7.3 it is calibrated.
But say you temporarily need to look a little wider, say 6 to 8 Mhz.
So you widen the stimulus window.
Now is the 7.0 to 7.3 still calibrated, and the areas out side close but
not?
Joe WB9SBD
--
*Dave - W?LEV*
*Just Let Darwin Work*
|
Re: How about using a USB memory stick instead of an SD card
#features
Greetings, Thank you for that information. But, I am not clear as to how to initiate an connection to,?and or the ability to exchange data to and from the SD Card which is installed into the NanoVna_H4?which I have. I did not notice any change of the device screen indicating a connection was now possible.?Also, I didn't notice any fields located in NanoVNA-saver application on my windows 10 PC. Must I install,?or re-install device firmware in order to affect the change that I have made by accessing the card slot.?Thank You
toggle quoted message
Show quoted text
On Thursday, December 9, 2021, 10:59:54 AM EST, DiSlord <dislordlive@...> wrote:
My NanoVNA? H/H4 fw support commands for SD card access, so some one can write software for work.
sd_list {pattern}
sd_read {filename}
sd_delete {filename}
Commands:
sd_list {pattern}
example get all files list
sd_list
or
sd_list *.*
Read s1p list
sd_list *.s1p
Read bmp list
sd_list *.bmp
Read s1p and s2p list
sd_list *.s?p
Read *.bin list
sd_list *.bin
Log {filename} {size}
18.238 rx: ch>
18.241 tx: sd_list *.bmp
18.243 rx: sd_list *.bmp
18.246 rx: sd_list:
18.250 rx: VNA_000004.bmp 153670
18.253 rx: VNA_00000C.bmp 153670
18.256 rx: VNA_210721_210606.bmp 307270
18.258 rx: VNA_000077.bmp 153670
18.261 rx: VNA_000114_212649.bmp 307322
18.300 rx: VNA_000119_233142.bmp 307322
18.303 rx: VNA_000119_233204.bmp 307322
18.306 rx: VNA_000119_233223.bmp 307322
18.309 rx: VNA_000122_082125.bmp 307322
18.312 rx: VNA_000129_085002.bmp 307322
18.315 rx: VNA_000129_085132.bmp 307322
18.318 rx: VNA_000129_085345.bmp 307322
18.321 rx: VNA_000129_085607.bmp 307322
18.323 rx: VNA_000129_091616.bmp 307322
18.326 rx: VNA_000129_091818.bmp 307322
18.361 rx: VNA_000301_213820.bmp 307322
18.364 rx: VNA_201129_081345.bmp 307322
18.368 rx: VNA_201129_081351.bmp 307322
18.371 rx: VNA_201129_081357.bmp 307322
18.374 rx: ch>
For read file need
sd_read {filename}
After nano return binary file data
or on error
"err: no file\r\n"
Delete file:
sd_delete {filename}
After nano delete it from SD card:
Output
shell_printf("delete: %s %s\r\n", filename, res == FR_OK ? "OK" : "err");
|
Re: Missing File or module?
Not sure but perhaps install the win 10 dev kit as suggested under the windows usage notes for pyinstaller here:
|
Re: How about using a USB memory stick instead of an SD card
#features
My NanoVNA H/H4 fw support commands for SD card access, so some one can write software for work.
sd_list {pattern}
sd_read {filename}
sd_delete {filename}
Commands:
sd_list {pattern}
example get all files list
sd_list
or
sd_list *.*
Read s1p list
sd_list *.s1p
Read bmp list
sd_list *.bmp
Read s1p and s2p list
sd_list *.s?p
Read *.bin list
sd_list *.bin
Log {filename} {size}
18.238 rx: ch>
18.241 tx: sd_list *.bmp
18.243 rx: sd_list *.bmp
18.246 rx: sd_list:
18.250 rx: VNA_000004.bmp 153670
18.253 rx: VNA_00000C.bmp 153670
18.256 rx: VNA_210721_210606.bmp 307270
18.258 rx: VNA_000077.bmp 153670
18.261 rx: VNA_000114_212649.bmp 307322
18.300 rx: VNA_000119_233142.bmp 307322
18.303 rx: VNA_000119_233204.bmp 307322
18.306 rx: VNA_000119_233223.bmp 307322
18.309 rx: VNA_000122_082125.bmp 307322
18.312 rx: VNA_000129_085002.bmp 307322
18.315 rx: VNA_000129_085132.bmp 307322
18.318 rx: VNA_000129_085345.bmp 307322
18.321 rx: VNA_000129_085607.bmp 307322
18.323 rx: VNA_000129_091616.bmp 307322
18.326 rx: VNA_000129_091818.bmp 307322
18.361 rx: VNA_000301_213820.bmp 307322
18.364 rx: VNA_201129_081345.bmp 307322
18.368 rx: VNA_201129_081351.bmp 307322
18.371 rx: VNA_201129_081357.bmp 307322
18.374 rx: ch>
For read file need
sd_read {filename}
After nano return binary file data
or on error
"err: no file\r\n"
Delete file:
sd_delete {filename}
After nano delete it from SD card:
Output
shell_printf("delete: %s %s\r\n", filename, res == FR_OK ? "OK" : "err");
|
Hi Joe, Anything that is saved is stored for future use. Once you've chosen a range to calibrate, you can turn the NanoVNA off and then just recall the stored calibration. As far as needing a wider range, I'm not sure, but it would be best just to calibrate it for the new range. 73, Zack W9SZ On Thu, Dec 9, 2021 at 8:41 AM Joe WB9SBD <nss@...> wrote: When you do a Calirate say between 3.5 and 4 Mhz, and save it.
Now next time you power the unit up (NanoVNA-H4)
And choose that saved profile, is that calibration still valid?
Or should you do it every time you power the unit up?
AND
OK again say you calibrate it between 7.0 and 7.3 Mhz. and save it to
another slot.
Now between 7.0 and 7.3 it is calibrated.
But say you temporarily need to look a little wider, say 6 to 8 Mhz.
So you widen the stimulus window.
Now is the 7.0 to 7.3 still calibrated, and the areas out side close but
not?
Joe WB9SBD
<> Virus-free. www.avg.com <> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
|
When you do a Calirate say between 3.5 and 4 Mhz, and save it.
Now next time you power the unit up (NanoVNA-H4)
And choose that saved profile, is that calibration still valid?
Or should you do it every time you power the unit up?
AND
OK again say you calibrate it between 7.0 and 7.3 Mhz. and save it to another slot.
Now between 7.0 and 7.3 it is calibrated.
But say you temporarily need to look a little wider, say 6 to 8 Mhz.
So you widen the stimulus window.
Now is the 7.0 to 7.3 still calibrated, and the areas out side close but not?
Joe WB9SBD
|
Re: How about using a USB memory stick instead of an SD card
#features
Use a toe nail clipper and a nail file? -? ;-)
toggle quoted message
Show quoted text
On Thursday, December 9, 2021, 09:08:19 a.m. EST, Robb Cole N2VJO <robbnterri@...> wrote:
Thx Larry...? At least it¡¯s been considered.? Back to figuring out how to ¡°hog out¡± the opening for the SD card in my nano VNA-H4 case.. :(
--
Regards,
Robb N2VJO
|
Re: How about using a USB memory stick instead of an SD card
#features
Thx Larry... At least it¡¯s been considered. Back to figuring out how to ¡°hog out¡± the opening for the SD card in my nano VNA-H4 case.. :(
--
Regards,
Robb N2VJO
|
Re: How about using a USB memory stick instead of an SD card
#features
Won't work - the Nano is a USB CLIENT.
You need to have a USB HOST port in order to plug in a memory stick.
This has been discussed before in the forum.
toggle quoted message
Show quoted text
On Wednesday, December 8, 2021, 09:29:52 p.m. EST, Robb Cole N2VJO <robbnterri@...> wrote:
A quick check on Amazon shows a simple USB female-to-female connector (set of two, actually) costs about $6.? One of those and the existing cable that comes with the NanoVNA gets you ¡°on the air¡± (assuming you have a USB memory stick, which they seem to be handing out in cereal boxes these days ?).
--
Regards,
Robb N2VJO
|
Re: How about using a USB memory stick instead of an SD card
#features
A quick check on Amazon shows a simple USB female-to-female connector (set of two, actually) costs about $6. One of those and the existing cable that comes with the NanoVNA gets you ¡°on the air¡± (assuming you have a USB memory stick, which they seem to be handing out in cereal boxes these days ?).
--
Regards,
Robb N2VJO
|
Re: How about using a USB memory stick instead of an SD card
#features
Great idea Robb
... or alternatively, make the internally installed SD card readable via the USB interface. No case modification would be required.
--
73
Gary, N3GO
|
How about using a USB memory stick instead of an SD card
#features
How about an off-the-wall suggestion from a newbie?
How hard would it be to use a USB memory stick on the already existing USB port? If that is feasible, then all users need do is buy an appropriate USB-female to USB-C cable..
Just thinking out loud...
--
Regards,
Robb N2VJO
|
Donald S Brant Jr
KK6DBR
Dave Johnson
Robb Cole N2VJO