开云体育

I have modified IC705.cxx to correct handling of DV mode. I had to add the DV bandwidths as well. They are the same as FM (per manual). I notice that the CI-V manual I have does not specify the mode

The command sequence names are INIT and CLOSE respectively.? See the attached for examples on the use for an Icom radio and for a Yaesu radio. 73, David, W1HKJ

Hi Phil I have also seen this briefly with my IC-9100 using WSJTX/JS8 through hamlib to flrig. It only affects PTT, not freq control. It wont TX. The DV "error" comes up when launched from the CLI. It

Hello, I am wanting to send commands on startup to the radio.?Does anyone know if there is a way to do this in the xml file? That is in the rig config file for fldigi (rigcat). 73 James

Dave, The results of my testing: IC-705 to flrig (i.e. get_*) Changing modes: LSB, USB, CW, CW-R, RTTY, RTTY-R, AM, AM-D, FM, FM-D, LSB-D, USB-D all OK. DV, WFM not OK. Changing filters: FIL1, FIL2,

Dave, From what I see DV is handled correctly between flrig and IC-705. But I would need to be a bit more thorough testing it before I can tell you for sure. I'll try and get round to it over the

I stand corrected.? flrig does support DV modes for the IC705 $ grep DV *705*cxx LSBD705, USBD705, AMD705, FMD705, DV705 ?? ?"LSB-D", "USB-D", "AM-D", "FM-D", "DV"};

DV is not supported by flrig / fldigi / hamlib.? You might be able to add it to the xml definition file for rigcat.? Let us know if you are successful. David P.S. flrig is open source.? You could

Delving into the hamlib code and tracing, it appears that hamlib doesn't understand the "DV" returned by flrig. I can see that this actually is a rats' nest. Maybe any mode that maps onto the ADIF

I need something that can be portable (backpack) so weight is very important. Herb Dr. Herb Sims? I want to tell the whole world that I love my wife and kids - what better way than one email at a

I have used this. https://www.amazon.com/gp/product/B07GSTM81Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1? Dahszhi Waterproof DC/DC 12V Step Up to 19V 10A 190W Voltage Boost Converter Regulator

This is what I am trying next: DC DC Buck Boost Converter Variable Voltage Regulator CC CV 0.5-30V 4A 5V 6V 12V 24V Power Module Adjustable Voltage Regulated Laboratory Power Supply amazon.com Herb

Hope it helps. I also use a RPi. On my 7300 I have the audio output set to 27% because I turn off the AGC to keep strong stations from dropping the gain. For AGC on then 50% usually is good. The 27&

I would use a MPPT charge controller and a battery. If the 19v is from the panel specs, they measure that open circuit. Under load it will be less as well as under less than full sun. The MPPT

Thanks, Cliff. The required audio level difference between wsjt-x and fldigi is informative. We used "IC-7100 How-to" from?"http://www.w1hkj.com/flrig-help/ic7100_how_to_page.html" for setup. We can

I don't know which side of the line this is, but I am accessing flrig using hamlib. When the IC-705 is set to DV mode and my app accesses hamlib::rig_get_mode() the returned mode is zero (no bits

I have a solar panel question. I have a 40W panel that outputs 19VDC on the DC5521 port. The input to the Chromebook charging port is also 19VDC. Should I have an MPTT between the panel and the laptop

Thanks Paul, If you read all of my post, you will see I made that mistake at first but then corrected it and still suffered the problem. My logger tried to connect to the last rig used regardless as

Both instances of flrig are trying to use the same port for xmlrpc (probably 12345). Only one server can be on the same port at one time. The second one will fail to start. If both could run together,

Thanks.