开云体育

edit: obviously I'm an idiot and didn't realize the typo in the title... Eimac not Eimax... ? Hi all, wondering if anyone has any data on this tube? Potential candidate for a 23cm amp. This came

The YU-106 appears to be a just 3-4 wraps of 3/8"? copper tubing wrapped around the anode. The YU-191B? is the real deal, with the coffee can around the anode.... just like all the other water

Dear Alek, Read your quest for the power meter manual, and herein certainly wish you success. Some chap wrote me the other day, looking for the manual for a 10KW ATU that was only manufactured for a

This is a really long shot. I am looking for a user manual and more importantly, a schematic for a "Agikawa APM-1H" automatic SWR and peak reading power meter, 1-8 ~ 60MHz. One is pictured here.

While working at Eimac San Carlos I wasn't involved with the Salt Lake City products but I have product announcements for both sites. "Oct 1989. The YU-191B was a version of the YU106 a water cooled

Hey Bob – I knew the 3CX1200s were tough little bastards, but I never knew they glowed as bright as that ! Very cool ! Sent: Friday, August 11, 2023 6:25 AM To: [email protected] Subject:

I have seen some inexpensive sorce ebay（$220/ea), it is seems a water cooled version of 3CX3000A7 but more power(driving power 535W and 8350W out put) Hsu

working on AL-1200 today.?? (the HV is off folks)?? Testing filament / blower settings.??? Photo attached of tube with blower/filament on.?? 73 If photo doesn't go through, it's on google

I like the bias boards I have them in use all over for years. I remote the pot to adjust rhe bias where I ever I want it. I run 6000 volts on a pair of 3-1000z tubes. But sometimes I run 4000 volts.

The W4ZT board was designed for the Russian tubes. ?It’s great for that. ?IMHO it’s not needed or wanted bd side I agree with Jim come glitch time kiss it bye-bye. Sent from the all new AOL app

Dear Adrian, VK4TUX, Thank you for your reply to the topic raised yesterday. (Electronic Bias / SB-220 / Advice) The references you sent are exactly what is available on-line for the W4ZT board.

Dear Mike, I saw this photo during my exhausting run of trying to find out what's under the hood. Yes, the Black and Red wire are sure visible. For me, though, it left questions unanswered, like "What

The problem with the adjustable W4ZT bias setup is..... come glitch time,? I can tell you exactly which components will fail. A simple string of 6A10's....or? 10A10's is dead nuts simple.? ?Use

I have been using the one from Ameritron. Joe WB9SBD

I have a new version of settable voltage electronic bias system (EBS) for SB-220 type of amps on my website. https://qsk2500.myfreesites.net/rf-amplifier-electronic-bias-ebs-2500 There are notes on

Greetings to the group, I am looking at a friends ALS-606S amp.? Its symptoms were low gain 4-5 dB on HF and virtually no gain on 6M. 50W drive gets you maybe 150-200W out across the bands.?

Uh oh, a ditto!! Keep in mind that Heath had a bit of a reputation for being cheapskates when it came to engineering design and parts acquisition, and those stud-mount zeners had barely enough

I have a new one if anyone would like to purchase it. Mike

Totally agree. My SB220 6m amp runs great with a few 6A10 diodes in series. Easy ! If you want two bias levels, add a shorting switch. Sent: Thursday, August 10, 2023 10:28 AM To:

Thanks Scott for replying. ?So let me try to understand... You had a small SLA Battery basically hooked up in parallel to your main auto battery? ?Without an isolator? ?Maybe this works because