开云体育

Several emails between me and Duncan Munro..who is also a ham. All these anomalies are being fixed as we speak. Also, if u do something stupid, like use less than the min inductance for a choke, on a

<Carl Dec 20 3:49 PM < I stopped using those 30-40 years ago even at 2500V < Carl ## OK, I'll bite. What do you use for hv connectors ??? ## On a similar note, buddy with the hipotronics hi pot tester

I stopped using those 30-40 years ago even at 2500V Carl

Solid-core spark plug wire -- Packard 440 or similar -- is the way to go. It's extremely durable, reasonably flexible, and good to well over 25 kV. If you're not comfortable with that, you can easily

Yes it is true. I understand he reached around the back of the amp to deal with some cables and grabbed the B plus line. These connectors are NOT shielded and neither is the wire.? There is simply no

Millen rated them to 7 KV

Drake uses em on the back of the L4B RF deck, but the HV lead coming out of the loom is like the center conductor + poly off of some 8-U coax and it's really short...and max of 2650 on it..on rx. I

Why would he be crazy enough to do that? Didn’t he know they are only rated for 2~2.5KV????? Mod-U-Lator, Mike(y)/W3SLK Sent: Wednesday, December 19, 2018 10:21 PM To: ham_amplifiers@...

Oh no! That is no laughing matter. I have a mate, who, 25 years ago, touched 3kV in his 4-1000A amp. When he came to, he was slammed up against his shack wall, 6 feet from where the amp was. Take care

E mail Icom, and see if they can help out, with either an original, or a suitable drop in substitute. Jim VE7RF

I heard through the grape vine that toll free / aka Shane, / KD6VXI, just about blew his finger off, on a Millen HV connector, with 6 kv on it. Don't ever get near one of those things, when there is

Working on an old IC-2KL and trying to find spec/source for a zener diode used in the PS, its listed as an XZ117, and suggestions? Ron K0IDX

I keep finding anomalies with PSUD-2. Like when a plane jane L-C filter is used, the + and - peak V across the choke is beyond sky high... like 17 + KV ! I tried every possible LC config you can think

For you folks that come across lytics, like the 450 vdc variety, that have a threaded stud (typ 12mm threads, that stick out the dead center of the bottom of the can by typ 1/2") look out, the

<Randy Nov 25 5:50 PM <Or, would you have to parallel them? I'm thinking that's the right answer. <Randy # Neither of your schemes will work. I just went through this with dahl / hammond. However,

<Alek Petkovic Nov 24 2:43 PM <I have not heard of 10A07s at all but Ebay is full of suppliers selling 10A10 diodes, which coincide with the <specs you quoted. <73, Alek. <VK6APK ## 10A10's are sold

Or, would you have to parallel them? I'm thinking that's the right answer. Randy

Jim: I wonder... "what if" somebody with way too much money needed 4H, and called one of the xfmr winders and ordered 2x 2H chokes, identical, *but* wound in opposite directions from each other....and

I have not heard of 10A07s at all but Ebay is full of suppliers selling 10A10 diodes, which coincide with the specs you quoted. 73, Alek. VK6APK

It's not something I've seen. With the 11M folks, I never pooh-pooh their discoveries or practices because sometimes they are right. I will say that we've had excellent results historically with