??? I need to find pricing for these Bergereda motors .? John I
think we may have the same mills ?? I noticed that the lower
spindle Collar? on my spindle was loose letting the spindle move
up & down in my spindle quill . Have ya ever had this issue
with yours ? If so should I just tighten it as much as I can &
reinstall or did ya find there was a sequence to do that . SO far
I haven't found much on this machine & the manual looks like
it was made by a drunk 4 year old with a Etch-A-Sketch .
Thanks
animal
On 11/3/24 11:49 PM, John Dammeyer
wrote:
toggle quoted message
Show quoted text
I¡¯m
now running Bergerda AX Servo¡¯s
on all axis with the exception of the 4th Axis
Harmonic drive which has a 3 phase motor but a different
Servo Driver.
?
Bergerda
does make a lot of motors for the sewing industry.? One time when I was
having some tuning issues their engineers made a quick video
using a cell phone and sent that to me to help me out.? Great support!
?
John
?
?
??? When ya say servo , are ya talking like one of those
Consew sewing machine servo motors ? I had forgotten all about
those units .
??? thanks
??? animal
On 11/3/24
1:21 AM, John Dammeyer wrote:
Here¡¯s
a photo of the original parts.? Thrust bearing at the
bevel gear end set the end play.? The shaft sat in the
cast iron and there was dramatic end play but then it was
designed to be turned slowly by hand.
?
At
the gear end the thrust bearings pressed against the gear
and the cast iron.? I
replaced the cast iron side with an bearing instead of a
bushing.
?
At
the crank end I replaced the bushing with bearings and
spacers and took out the end play to the bevel gear.? Now I can spin this
to get 150 IPM on the knee which is scary fast.
?
First
trial was with a 650 oz-in stepper motor with 4:1
reduction.? If I
was lucky I got 10 IPM before the motor locked up.? Stepper motors cannot
turn fast.? Changing
to a 1200 oz-in motor gave me 25 IPM and that worked until
the GECKO controller developed corrosion on the terminal
connector and failed.
?
From
there I changed out the motor to a 750W AC Servo good to
3000 RPM and now have 150 IPM.
?
Eventually
I¡¯ll drive the vertical screw directly to reduce backlash
but for now it¡¯s been pretty good.
John
?
?
?
Hit send too fast . The knee is the one that I will
probably convert first . I had my chest cracked 7 years back
& thinks like raising/lowering the knee reminds me that
that work\was done to me . I have one of those electric seat
motors , but i don't think it has enough power for this . I
think my next plan is to remove the table & go down to
the knee mechanism & clean, lube & adjust my way
back up to the table .? I would be interested to see how ya
/ yer bud did the Stepper? & DC motor install .
thanks
animal
On 11/2/24
11:19 PM, mike allen wrote:
??? Sorry Forgot to mention , ye it's a knee mill I was
told it was purchased new in the 80's . It Came from KBC
tool's . I got it from the original owner whose work was
95 % plastic , no steel & some aluminum . He made some
kind of optics stuff .
thanks
?animal
On 11/2/24
10:48 PM, John Dammeyer wrote:
Does your mill have a knee or does the head assembly move?? That's easier than moving the quill and leaves the quill as a manual option.
?
There are all sorts of ways of doing this.? For the longest time I had a stepper motor on the knee shaft that I ran from one of my ELS units.? I could set zero where I was milling and then if I wanted to do a 0.010" cut just move the knee by that distance.
?
A friend of mine with the same type of mill just added a DC motor with a variable power supply and a couple of toothed belts and uses it to avoid major tedious cranking operations.
?
Or, start thinking about CNC now and start the conversion.? Just do the Z axis to start.? Whatever controller you use add a pendant with an MPG and now you are on the way with adequate control.
?
-----Original Message-----
From: [email protected] [mailto:[email protected]] On
Behalf Of mike allen
Sent: November 2, 2024 10:27 PM
To: [email protected]
Subject: [digitalhobbyist] Diy Powerfeed for mill
?
? Finally got my mill in my machine room & under power . Wondering if
anyone here has come up with a DIY powerfeed that could be used on a mill .
?
thanks
?
animal
?
?
?
?
?
?
?
?
