HTs, Xcvr,PS, manuals and more FS
Dual Band HTs, HF + VHF + UHF Transceiver,
Power Supply, Manuals, and more For Sale:
.
Yaesu FT-470 Dual Band HT:
The innovative Yaesu FT-470 2M/440 HT has many
sophisticated features, built into a robustly
built chassis with easy-to-use external controls.
It boasts four VFOs and 42 memories plus an
impressive backlit dual band LCD. Power output
can be as high at 5 watts depending on battery
pack used. It has a very "tight" front end on
the receiver, keeping a lot of intermod out.
Features:
42 Memories
4 VFOs
DTMF Keypad
DTMF Auto Dialer
Scanning
Backlit Keypad
CTCSS Encode
Auto Repeater Shift
Auto Power Off
This particular unit works 100% and looks extremely nice.
It has an aftermarket FNB-12, 12 volt 700 mahr battery
pack. Also included is the dual band rubber duck antenna,
wrist strap, wall charger, and paper work for $100
.
Yaesu FT-60 Dual Band HT:
The Yaesu FT-60R dual-band 2 meter/440 MHz HT
has 5 watts output on both bands. It also features
wideband receive from 108-520 and 700 to
999.990 MHz.
It includes One touch NOAA weather, nine DTMF
auto dialer memories, die-cast weather resistant
case, ARTS Auto-range transponder system.
2.3 x 4.3 x 1.2 inches, 13.1 oz
Features:
Over 1000 Memories
5 Watts RF Output
Backlit Keypad
Alphanumeric Display
NOAA Weather Alert
PL Encode/Decode
CS Encode/Decode
Emergency Auto ID System
This one works fine and looks fine. No scratches
or defects. It includes rubber duck, belt clip,
FNB-83 battery, charger, and paper work for $100
.
Yaesu FT-847 HF+++ Transceiver:
The Yaesu FT-847 changes base operation
forever. Now you get three radios in one
-- HF, VHF/UHF and satellite. You get 100
watt output on HF and 6 Meters, plus 50
watts on both 2 Meters and 430 MHz bands.
Additional features include: Cross-band
Full Duplex operation, Normal/Reverse
Tracking, CTCSS/DCS Encode and Decode,
0.1 Hz tuning steps, DSP Notch, DSP NR
and DSP BPF, Shuttle Jog Tuning Dial,
Carry Handle and Keypad Entry.
The FT-847 is also 1200/9600 bps Packet
ready.
10.2 x 3.4 x 10.6 inches.
Features:
HF/VHF/UHF
DSP Filters
Dual Watch
0.1 Hz Tuning
CTCSS/DCS Decode and Encoode
Cross-band Full Duplex
1200/9600 Packet Ready
It covers all of the normal ham bands in one
package with virtually all modes!
This one works 100% and looks like new.
No defects.
With paper work for $775.
.
Yaesu FP-707, 20 Amp Speaker/Power Supply:
The Yaesu FP-707 is a 20 amp 13.8 Volt DC
Power Supply, with a very nice front facing
speaker in the same enclosure.
Cosmetically, it matches the FT-707, FT-747,
FT-757 and likely others.
Electrically, it can provide up to 20 amps,
so will work with most any HF and/or VHF rig.
It also has a set of binding posts on the back
for easy connection of a rig in addition
to the HF rig.
The speaker has a 3.5 mm plug on it.
This particular unit is in very good shape
both electrically and cosmetically. I can
not find a scratch, dent, or ding on it.
Electrically, it works as it should.
Buy this unit with manual for $120.
.
Yaesu NC-9 B Charger
13 V DC at 45 ma, 2.5 mm plug; $12
.
Original Yaesu Manuals:
These are the manuals only. All are originals, and not copies.
Most are in close to new condition.
FNB-9,10,11,12 Battery packs, $2
FC-757AT Antenna Tuner, $10
FT-100 HF/VHF Transceiver, $18
FT-470 Dual Band HT, $10
FT-757 GX, HF Transceiver, $18
FT-720 R, 2 meter mobile, $8
FT-1802 M, 2 meter mobile, $12
FT-2700 Dual Band Xcvr, $12
FTH-2005 HT, $5
FTS-8 tone squelch unit, $3
FTS-12 tone squelch unit, $3
MH-1B A2B speaker microphone, $2
SP-101 P, Speaker / Phone patch, $5
VX-1 dual band HT, $10
Maintenance Service Manual for Yaesu FT-208 R
2 meter HT. Looks new. $25
Technical Supplement for Yaesu FT-2700
Dual Band Mobile. Looks new. $20
These are original Yaesu operating manuals only,
in very nice condition.
.
I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.
.
Prices do not include shipping from Florida.
Thanks.
73,
Ken, W8EK
Ken Simpson
E-mail to W8EK@... or W8EK@...
Voice Phone (352) 732-8400
|
Re: No receive full scale
Ok I can hepl6you here, when I get home next week, I will guide you through the repair.
Check the circuits and find the AGC line, it will close to the IF output, follow it back to the RF amp.
There maybe a negative rail generator, if so check this is working.
73
For now
Andrew
?Get BlueMail for Android ?
toggle quoted message
Show quoted text
On 13 Jul 2024, 13:04, at 13:04, Noel W2MSA <noelw2msa@...> wrote: I would like to fix it myself, if not, I would like to send it to get
fixed in the states.
thank you
|
Re: No receive full scale
I would like to fix it myself, if not, I would like to send it to get fixed in the states.
thank you
|
Re: No receive full scale
Adjusting rf gain makes no difference.
|
Re: No receive full scale
Where to look and fix this issue?
----- Mensagem de Andrew Lenton < a@...> --------- Data: Sat, 13 Jul 2024 08:43:41 +0100
De: Andrew Lenton < a@...> Assunto: Re: [YaesuFT847] No receive full scale
AGC fault, fairly simple
I live in the UK so logistics are expensive
?Get BlueMail for Android
On 13 Jul 2024, 01:55, at 01:55, Andy Bosworth < sidthepop@...> wrote:
RF Gain up?
On Sat, 13 Jul 2024, 00:22 Noel W2MSA via groups.io, <noelw2msa=
My FT-847 that is used on a weekly basis now has no receive yet meter
is
displaying full scale on any band and any mode except for FM.
Looking for a repair tech.
73, de W2MSA
----- Fim da mensagem de Andrew Lenton < a@...> -----
|
Re: No receive full scale
AGC fault, fairly simple
I live in the UK so logistics are expensive
?Get BlueMail for Android ?
toggle quoted message
Show quoted text
On 13 Jul 2024, 01:55, at 01:55, Andy Bosworth <sidthepop@...> wrote: RF Gain up?
On Sat, 13 Jul 2024, 00:22 Noel W2MSA via groups.io, <noelw2msa=
[email protected]> wrote:
My FT-847 that is used on a weekly basis now has no receive yet meter is
displaying full scale on any band and any mode except for FM.
Looking for a repair tech.
73, de W2MSA
|
Re: No receive full scale
toggle quoted message
Show quoted text
My FT-847 that is used on a weekly basis now has no receive yet meter is displaying full scale on any band and any mode except for FM.
Looking for a repair tech.
73, de W2MSA
|
My FT-847 that is used on a weekly basis now has no receive yet meter is displaying full scale on any band and any mode except for FM.
Looking for a repair tech.
73, de W2MSA
|
Re: FT-847 IN TX ALL TIMES
I never use this plug into the extension speaker socket.?
It not needed if you use the mic input on the PC or laptop and use the amp on the soundcard to boost the signal get the desired input level.?
I think was designed for soundcard interfaces that have low level input line-in only. ?
73 de Ian G8ZHC
Ah, that's much better.
So, a question:? With that bottom right connector going to the
external speaker jack, the audio input to the computer's sound card
becomes dependent on the volume setting on the front panel which is
annoying and prone to error.? I presume it also interrupts the
internal speaker, so can't simply be left in.?
Is it needed?
Greg? KO6TH
Ian M via wrote:
Hopefully this version is uncropped as I did the previous
version from my phone.
Nice circuit, but it's slightly
cropped.? The two plugs on the right...? The top one goes to
the TRS Data I/O port; where does the lower one go, and what
is the rest of the "USE THIS F..." text?? Seems to be
important...
Greg? KO6TH
Ian M via wrote:
This is what have been using for the last
25 years with the FT-847 with various data modes in
both SSB & FM including FT-8
Credit goes to ( I think) Jim Barber
N7CXI who co-wrote W95SSTV which it was initially
designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M,
no problem.? Just used the sample interface circuit
in the manual.??
73,
Tom K6EU
MAN, you
guys are good !!!!..? Very obvious thing
overlooked. HI.? All good now.? I had schematics
out last night trying to figure out what
components could be bad.? You made my day.? Any
of you using something for FT8?? I had it
receiving FT8 through the DATA IN/OUT plug but
was trying to get transmit working.? I notice
there was a claim that the DATA IN/OUT only
worked on HF and I wanted it for 6 M. Probably
have to go into mic jack for that and PTT.? Any
units on the market that do that?? Have not
looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Ah, that's much better.
So, a question:? With that bottom right connector going to the
external speaker jack, the audio input to the computer's sound card
becomes dependent on the volume setting on the front panel which is
annoying and prone to error.? I presume it also interrupts the
internal speaker, so can't simply be left in.?
Is it needed?
Greg? KO6TH
Ian M via groups.io wrote:
toggle quoted message
Show quoted text
Hopefully this version is uncropped as I did the previous
version from my phone.
Nice circuit, but it's slightly
cropped.? The two plugs on the right...? The top one goes to
the TRS Data I/O port; where does the lower one go, and what
is the rest of the "USE THIS F..." text?? Seems to be
important...
Greg? KO6TH
Ian M via wrote:
This is what have been using for the last
25 years with the FT-847 with various data modes in
both SSB & FM including FT-8
Credit goes to ( I think) Jim Barber
N7CXI who co-wrote W95SSTV which it was initially
designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M,
no problem.? Just used the sample interface circuit
in the manual.??
73,
Tom K6EU
MAN, you
guys are good !!!!..? Very obvious thing
overlooked. HI.? All good now.? I had schematics
out last night trying to figure out what
components could be bad.? You made my day.? Any
of you using something for FT8?? I had it
receiving FT8 through the DATA IN/OUT plug but
was trying to get transmit working.? I notice
there was a claim that the DATA IN/OUT only
worked on HF and I wanted it for 6 M. Probably
have to go into mic jack for that and PTT.? Any
units on the market that do that?? Have not
looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Hopefully this version is uncropped as I did the previous version from my phone.
Nice circuit, but it's slightly cropped.? The two plugs on the
right...? The top one goes to the TRS Data I/O port; where does the
lower one go, and what is the rest of the "USE THIS F..." text??
Seems to be important...
Greg? KO6TH
Ian M via wrote:
This is what have been using for the last 25
years with the FT-847 with various data modes in both SSB
& FM including FT-8
Credit goes to ( I think) Jim Barber N7CXI who
co-wrote W95SSTV which it was initially designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M, no
problem.? Just used the sample interface circuit in the
manual.??
73,
Tom K6EU
MAN, you guys are good
!!!!..? Very obvious thing overlooked. HI.? All good
now.? I had schematics out last night trying to figure
out what components could be bad.? You made my day.? Any
of you using something for FT8?? I had it receiving FT8
through the DATA IN/OUT plug but was trying to get
transmit working.? I notice there was a claim that the
DATA IN/OUT only worked on HF and I wanted it for 6 M.
Probably have to go into mic jack for that and PTT.? Any
units on the market that do that?? Have not looked.? 73
Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Nice circuit, but it's slightly cropped.? The two plugs on the
right...? The top one goes to the TRS Data I/O port; where does the
lower one go, and what is the rest of the "USE THIS F..." text??
Seems to be important...
Greg? KO6TH
Ian M via groups.io wrote:
toggle quoted message
Show quoted text
This is what have been using for the last 25
years with the FT-847 with various data modes in both SSB
& FM including FT-8
Credit goes to ( I think) Jim Barber N7CXI who
co-wrote W95SSTV which it was initially designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M, no
problem.? Just used the sample interface circuit in the
manual.??
73,
Tom K6EU
MAN, you guys are good
!!!!..? Very obvious thing overlooked. HI.? All good
now.? I had schematics out last night trying to figure
out what components could be bad.? You made my day.? Any
of you using something for FT8?? I had it receiving FT8
through the DATA IN/OUT plug but was trying to get
transmit working.? I notice there was a claim that the
DATA IN/OUT only worked on HF and I wanted it for 6 M.
Probably have to go into mic jack for that and PTT.? Any
units on the market that do that?? Have not looked.? 73
Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Quite agree this would be an improvement.? I used a 4N25 optocoupler on my FT-100 interface (that has a slightly different configuration) and still use it today with the FT817
Built several of these over?the years for myself and friends each one more nearer than the previous one.?
It works both for SSB and FM and doesn't affect the CAT interface if you are not using the matching FC-20 auto atu.?
On Thu, 6 Jun 2024, 15:53 Spence G5STO via , <unavailable.equal= [email protected]> wrote: Hi Ian, that’s a beautiful circuit and could only be improved by replacing the 2N2222 with a 4N33.
De Spence G5STO
Sent while portable! please excuse typos. ? This is what have been using for the last 25 years with the FT-847 with various data modes in both SSB & FM including FT-8
Credit goes to ( I think) Jim Barber N7CXI who co-wrote W95SSTV which it was initially designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M, no problem.? Just used the sample interface circuit in the manual.??
73,
Tom K6EU
MAN, you guys are good !!!!..? Very obvious thing overlooked. HI.? All good now.? I had schematics out last night trying to figure out what components could be bad.? You made my day.? Any of you using something for FT8?? I had it receiving FT8 through the DATA IN/OUT plug but was trying to get transmit working.? I notice there was a claim that the DATA IN/OUT only worked on HF and I wanted it for 6 M. Probably have to go into mic jack for that and PTT.? Any units on the market that do that?? Have not looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Hi Ian, that’s a beautiful circuit and could only be improved by replacing the 2N2222 with a 4N33.
De Spence G5STO
Sent while portable! please excuse typos.
toggle quoted message
Show quoted text
On 6 Jun 2024, at 15:42, Ian M via groups.io <nightflyian@...> wrote:
? This is what have been using for the last 25 years with the FT-847 with various data modes in both SSB & FM including FT-8
Credit goes to ( I think) Jim Barber N7CXI who co-wrote W95SSTV which it was initially designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M, no problem.? Just used the sample interface circuit in the manual.??
73,
Tom K6EU
MAN, you guys are good !!!!..? Very obvious thing overlooked. HI.? All good now.? I had schematics out last night trying to figure out what components could be bad.? You made my day.? Any of you using something for FT8?? I had it receiving FT8 through the DATA IN/OUT plug but was trying to get transmit working.? I notice there was a claim that the DATA IN/OUT only worked on HF and I wanted it for 6 M. Probably have to go into mic jack for that and PTT.? Any units on the market that do that?? Have not looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
This is what have been using for the last 25 years with the FT-847 with various data modes in both SSB & FM including FT-8
Credit goes to ( I think) Jim Barber N7CXI who co-wrote W95SSTV which it was initially designed for.
Hope it helps
I've used my FT-847 on both 6 and 2M, no problem.? Just used the sample interface circuit in the manual.??
73,
Tom K6EU
MAN, you guys are good !!!!..? Very obvious thing overlooked. HI.? All good now.? I had schematics out last night trying to figure out what components could be bad.? You made my day.? Any of you using something for FT8?? I had it receiving FT8 through the DATA IN/OUT plug but was trying to get transmit working.? I notice there was a claim that the DATA IN/OUT only worked on HF and I wanted it for 6 M. Probably have to go into mic jack for that and PTT.? Any units on the market that do that?? Have not looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
I've used my FT-847 on both 6 and 2M, no problem.? Just used the sample interface circuit in the manual.??
73,
Tom K6EU
MAN, you guys are good !!!!..? Very obvious thing overlooked. HI.? All good now.? I had schematics out last night trying to figure out what components could be bad.? You made my day.? Any of you using something for FT8?? I had it receiving FT8 through the DATA IN/OUT plug but was trying to get transmit working.? I notice there was a claim that the DATA IN/OUT only worked on HF and I wanted it for 6 M. Probably have to go into mic jack for that and PTT.? Any units on the market that do that?? Have not looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
MAN, you guys are good !!!!..? Very obvious thing overlooked. HI.? All good now.? I had schematics out last night trying to figure out what components could be bad.? You made my day.? Any of you using something for FT8?? I had it receiving FT8 through the DATA IN/OUT plug but was trying to get transmit working.? I notice there was a claim that the DATA IN/OUT only worked on HF and I wanted it for 6 M. Probably have to go into mic jack for that and PTT.? Any units on the market that do that?? Have not looked.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
Check to insure the MOX?button is not pushed in.? ?The MOX button is right under the power switch, easy to push by mistake.
73,
Tom K6EU
You didn't by any chance bump the MOX switch on the front?
Greg? KO6TH
K4PI via wrote:
I have a 847 that had been
working fine until I started tinkering with the DATA IN/OUT
jack trying to interface a computer.? Now when I turn power on
it is in TX continually and cannot get it out? Nothing but DC
power and antenna connected.? Think something got blown on
that circuit.? Unable to make any changes. Anyone every
working in that area.? 73 Mike K4PI
|
Re: FT-847 IN TX ALL TIMES
You didn't by any chance bump the MOX switch on the front?
Greg? KO6TH
K4PI via groups.io wrote:
toggle quoted message
Show quoted text
I have a 847 that had been
working fine until I started tinkering with the DATA IN/OUT
jack trying to interface a computer.? Now when I turn power on
it is in TX continually and cannot get it out? Nothing but DC
power and antenna connected.? Think something got blown on
that circuit.? Unable to make any changes. Anyone every
working in that area.? 73 Mike K4PI
|
I have a 847 that had been
working fine until I started tinkering with the DATA IN/OUT jack
trying to interface a computer.? Now when I turn power on it is
in TX continually and cannot get it out? Nothing but DC power
and antenna connected.? Think something got blown on that
circuit.? Unable to make any changes. Anyone every working in
that area.? 73 Mike K4PI
|
Andrew Lenton
Andy Bosworth
Ian M
Spence G5STO