开云体育

Has anyone added the dds vfo to the S forty 9er with wifi by lxqqfy? The pcb layout is way different but they have an app to convert CW on the Iphone to the transmitter working on my extra and I might

Forgot,kl4fo

Has anyone added the dds vfo to the S forty 9er with wifi by lxqqfy? The pcb layout is way different but they have an app to convert CW on the Iphone to the transmitter working on my extra and I might

I knew it wouldn't be long before I was over my head with this project! Upload ain't working. I'm using a knockoff geeetech.com Iduino NANO v3.0. uses FTDI FT232RL. Computer is an old Dell laptop

I also built the Super Rockmite 51 and was able to get it working. Agreed, the 'typical' documentation is awful but once I found something decent it started making sense. I get about 6 watts out of

Hi Bob, You didn't comment on the controller. Did you use the STC12C4052? Have you got a PC software which works through the serial port? - or do you agree - forget that part of it and use an external

In my case I hadn't wired any supply voltages to my headers except for the display so it was easier to just pop two resistors and leave the wiring and SW alone (for now). - John W1JDS

Ok, thanks. I bought a bunch of pre-made jumpers with connectors already on each end and was kinda expecting it to match up directly like the drawing shows. Don't have any experience in these things.

I guess I don't see the issue. Use dupont jumpers: SDA to Pin 16 of J1SCL ? ? ? ? ? ?14Vcc ? ? ? ? ? ? 10GND ? ? ? ? ? 12 Jack, W8TEE To: SoftwareControlledHamRadio@...

Hi, I'm using ZIAs kit and the display module usess a YwRobot Arduino. I note the pinout order doesn't match the board pinout. Do I have the correct module and simply need to make up an individual

I just posted a note about connecting it to J1...maybe that will help. Jack, W8TEE To: SoftwareControlledHamRadio@... Sent: Wednesday, November 2, 2016 6:54 AM Subject:

Hi Bob: Email me on your efforts relative to the DDS. A VFO makes QRP that much more successful! Jack, W8TEE To: SoftwareControlledHamRadio@... Sent: Wednesday, November 2, 2016 8:31 AM

Actually, the better way to connect the encoder is to use the header pins on J1. CLK --- Pin 22DT ? --- Pin 18SW ?--- Pin 17+ ? ? ?--- Pins 7, or 8, or 9, or 10GND ---?Pins 20, or 19, or 12, 0r

I got it working by removing the 2 pull-up resistors on the back of the PCB. Pull-ups are already configured in the code. Only 4 wires are needed this way on my setup. - John W1JDS

Hi folks, new member here. I'm working on the DDS-VFO kit from K2ZIA. Arduino stuff is totally new to me but thanks to his FB instructions I think I have a chance :) I'm at the point where its ready

FIXED IT! Using a rotary encoder with push button type: KY-040 with 5 connectors. The interconnections needs to be: From KY-040 to the DDS Board: CLK --- Pin 24 DT --- Pin 18 SW --- Pin 21 + --- 5V

I have 2 super rockmites.I built them with crystal sockets so I can change frequencies. I have used them on 7.030 and 7.050 with good success. Both have outputs over 6 watts. I am looking at building

Hi gang, I just completed my VFO DDS using theNANO DDS VFO Kit Rev_2 (3-30Mhz) from K2ZIA, W8TEE and W6DQ. + Board is OK and running + Software is uploaded to the NANO and running, too + VFO signal on

I just found out about the work by John Clements, KC9ON, with a number of Chinese radios, including the 49-er and the SRM. You can see his info on the SRM at:

There s an excellent guide to building the RM here Chinese Super RM Rockmite AKA Octopus - 3rd Planet Solar / KC9ON