开云体育

Tim My system is V10 but the boards and box are the same size I think. My boards are all mounted with the mounting holes at the top.? My different card holders have long vertical arms and the details

You can fully modularize the display code or even remove it from the T41 software entirely, but it would take a lot of work.? A lot can still be done without going to such extremes though.? I have a

“Different power connector on boards, getting to those screws when in a case is torture. I installed a distribution strip on back panel with 2 pin molex connectors to make it easier to take out

Forgot the TDA7312…. One of my favorite parts! Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner

“I have mentioned to Bill and Oliver that I would like to see a small PCB hold the 4 connectors (mic, PTT, headphones, and key) just because the current direct wiring makes the front look like a

Couple of hardware changes I would like: Different power connector on boards, getting to those screws when in a case is torture. I installed a distribution strip on back panel with 2 pin molex

My sincere gratitude to all of you for such an exciting project. Best regards, Jack Mann W1QZ [email protected]> wrote:

All:Obviously I agree since I suggested to Al that Bill take the hardware over, to which he was in total agreement. Same for Oliver on the software track: both were done in consultation. In the

Like Oliver on the Software side, I have graciously been handed the hardware side of the T41 development moving forward. (Just my take with this next statement) The software side is easier to

It was super easy to setup and upload, I down loaded the zip code, opened in IDE 2.3.6, did the 3 library updates, setup Teeny download variables and it compiled first time! I did not change anything

Hey Oliver, I have no problem with you moving the test routines to your GITHUB. They surely will get more maintenance attention there than on my GITHUB… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK

The README file on GitHub describes how to set up the build environment and install all the required libraries: https://github.com/KI3P/SDTVer066-9/blob/main/README.md In general, you should try to

Hi Jack, looking back I remember you and Al did take the first giant leap to modularize the code.? From the single-file SDR Convolution Receiver project, to multiple files. I've done two different

Sounds like a plan. I have V2 of the book, and will order the final edition in the near future.? I have the V12 board set.? I've made a few changes to the way the boards and controls are connected,

Thank you, Oliver, we need a stable for slow bulders. [email protected]> wrote:

All:I agree with everything Oliver has stated here. I should have done a better job of structuring the code from the outset, but at the start, it was just Al and I working on the T41, and we were

As Jack mentioned in a recent post ( /g/SoftwareControlledHamRadio/message/33345?p=%2C%2C%2C20%2C0%2C0%2C0%3A%3Acreated%2C%2CJack%20KI3P%2C20%2C2%2C0%2C112085546 ) , I've accepted the

Ok… invoice incoming… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

Hi Bill I would like to order a full set of V12 Boards Paypal address hobergenix@... Mike Hoblinski 7817 Vineland Ave Apt 47 Sun Valley CA 91352 Ham Radio Experimenting Fun Education N6IMF

Try loading one of the example programs from the RA8875 library to see if it runs with the Teensy. Jack, W8TEE