开云体育

Well I did it again, shorted out the teensy. Now wait for another. Tom

Bill Even RPi 0 has HDMI! Could it be dedicated display module? I think there even smaller ones also. Tim

I'm deep in the weeds of learning about Test Driven Development (TDD) and stateful programming. I'll be doing some experiments and writing some test code to get more familiar with the programming

Maybe even a RPi that has native HDMI circuitry... maybe even multiple display capability (think main plus an external display). Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ

Inside the T41 code: grep tft * > out Looking at out: it has 2484 lines. There are a few ways this could be approached. One would be that replacement class for the RA8875 stuff. It could have

Yeah Terrance did that… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

Tim My system is V10 but the boards and box are the same size I think. My boards are all mounted with the mounting holes at the top.? My different card holders have long vertical arms and the details

You can fully modularize the display code or even remove it from the T41 software entirely, but it would take a lot of work.? A lot can still be done without going to such extremes though.? I have a

“Different power connector on boards, getting to those screws when in a case is torture. I installed a distribution strip on back panel with 2 pin molex connectors to make it easier to take out

Forgot the TDA7312…. One of my favorite parts! Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner

“I have mentioned to Bill and Oliver that I would like to see a small PCB hold the 4 connectors (mic, PTT, headphones, and key) just because the current direct wiring makes the front look like a

Couple of hardware changes I would like: Different power connector on boards, getting to those screws when in a case is torture. I installed a distribution strip on back panel with 2 pin molex

My sincere gratitude to all of you for such an exciting project. Best regards, Jack Mann W1QZ [email protected]> wrote:

All:Obviously I agree since I suggested to Al that Bill take the hardware over, to which he was in total agreement. Same for Oliver on the software track: both were done in consultation. In the

Like Oliver on the Software side, I have graciously been handed the hardware side of the T41 development moving forward. (Just my take with this next statement) The software side is easier to

It was super easy to setup and upload, I down loaded the zip code, opened in IDE 2.3.6, did the 3 library updates, setup Teeny download variables and it compiled first time! I did not change anything

Hey Oliver, I have no problem with you moving the test routines to your GITHUB. They surely will get more maintenance attention there than on my GITHUB… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK

The README file on GitHub describes how to set up the build environment and install all the required libraries: https://github.com/KI3P/SDTVer066-9/blob/main/README.md In general, you should try to

Hi Jack, looking back I remember you and Al did take the first giant leap to modularize the code.? From the single-file SDR Convolution Receiver project, to multiple files. I've done two different

Sounds like a plan. I have V2 of the book, and will order the final edition in the near future.? I have the V12 board set.? I've made a few changes to the way the boards and controls are connected,