|
MT63
Hi everyone, I have given a try at soundcard digitalmodes. I have added MT63 to the Java version of Ham Radio Integrator. I have MARS in mind - that's why I chose to start with MT63. First I got an
By
Howard Z
·
#79
·
|
|
Re: M710 data strings for remote
Hmmmm, not so strait forward then. my luck again i would say. still no answer from barrett about the 2050 also. probably not important enough i gues. :-) regards jaap
By
Jacob
·
#78
·
|
|
Re: M710 data strings for remote
Jacob, There is a document in a M710 yahoo group which has a document showing all the commands for the Icom marine radios. Unfortunately each command has a checksum which must be calculated, and you'd
By
Howard Z
·
#77
·
|
|
M710 data strings for remote
good day howerd. did you document what strings you send to the M710 for the each setting and what answer you expect ? would like to try and add them to hamlib. what is there does not work? if so,
By
Jacob
·
#76
·
|
|
Re: rig control
Jacob, For the M710A all radio commands start with "$PICOA" and end with a two digit checksum. It is all plain printable ASCII characters - no binary. Howard
By
Howard Z
·
#74
·
|
|
Re: rig control
i will try to get it from barrett and drop it in you mail box might take some time thoug? when i have it i will contact you again. on the M710 the prog just runs fine. concerning the mode switching.
By
Jacob
·
#73
·
|
|
Re: rig control
Just email the information to me.
By
Howard Z
·
#72
·
|
|
Re: rig control
To use HRI with ham radio deluxe (HRD) Logbook or DM780, you should never run the main HRD program. HRI takes the place of Head's main program. HRI shares information with Logbook and DM780. Just run
By
Howard Z
·
#71
·
|
|
Re: rig control
good day howerd. there is a hamlib database representing the barrett. it is also supported in winlink the barrett is by the way an australian tranceiver that is frequently used in the australian
By
Jacob
·
#70
·
|
|
Re: rig control
§©§Õ§â§Ñ§Ó§ã§ä§Ó§å§Û§ä§Ö §¤§à§Ó§Ñ§â§Õ! . §£§à§á§â§à§ã- §Ü§Ñ§Ü §Ù§Ñ§Ü§à§ß§ß§Ö§Ü§ä§Ú§ä§î HRI §ã §á§â§à§Ô§â§Ñ§Þ§Þ§à§Û §Õ§Ö§Ý§ð§Ü§ã. §µ §Þ§Ö§ß§ñ §ß§Ö §á§à§Ý§å§é§Ñ§Ö§ä§ã§ñ. §±§à§Õ§ã§Ü§Ñ§Ø§Ú§ä§Ö. §³
By
r7khs
·
#69
·
|
|
Re: rig control
Hi Jacob, The answer is no. HRI has all radio controls hard coded. I might consider adding your radio if 1. You can provide details of the protocol for communicating with the radio. I did not find it
By
Howard Z
·
#68
·
|
|
rig control
good day gents. a question. ?does HRI integrater use a hamlib like structure for the control of rigs and would it be possible to ad on my self (barrett 2050)
By
Jacob
·
#67
·
|
|
Re: Visual Studios HRI test version 17 MAR 2017
Howard, I have tested today's 17 MAR 2017 test version of HRI with USB to Clone port of IC M710 cable with HRI set for no flow control. Radio controls work but as usual the M710 report backs of radio
By
Tom
·
#66
·
|
|
Re: Visual Studios HRI test version 17 MAR 2017
Well Howard. Tomorrow I will be engaged densely in the program. Many thanks for the program. Here so at me the program window looks now.
By
r7khs
·
#65
·
|
|
Visual Studios HRI test version 17 MAR 2017
There is a new test version HRI-TEST.zip in the files section. Version 17 MAR 2017. This allows FLOW CONTROL settings options for all radios that use a regular RS232 COM Port.? (Not available for
By
Howard Z
·
#64
·
|
|
Re: New file uploaded to [email protected]
Thank you for the program. So far I use it on SAT. Very conveniently. §³ §å§Ó§Ñ§Ø§Ö§ß§Ú§Ö§Þ, §¯§Ú§Ü§à§Ý§Ñ§Û §ª§ã§Ý§Ö§ß§ä§î§Ö§Ó r7khs@... 73!
By
r7khs
·
#63
·
|
|
Re: icom-m802
§³ §å§Ó§Ñ§Ø§Ö§ß§Ú§Ö§Þ, §¯§Ú§Ü§à§Ý§Ñ§Û §ª§ã§Ý§Ö§ß§ä§î§Ö§Ó r7khs@... 73!
By
r7khs
·
#62
·
|
|
Re: icom-m802
Bits/Sec = 9600 ? Data Bits = 8 ? Parity = none ? Stop bits = 1 ? Flow Control = none ?
By
Tom
·
#61
·
|
|
Re: icom-m802
COM 1 = 9600 §³ §å§Ó§Ñ§Ø§Ö§ß§Ú§Ö§Þ, §¯§Ú§Ü§à§Ý§Ñ§Û §ª§ã§Ý§Ö§ß§ä§î§Ö§Ó r7khs@... 73!
By
r7khs
·
#60
·
|
|
Re: icom-m802
Nikolay COM 1 = 4800?
By
Tom
·
#59
·
|