开云体育

I am currently using these HRI settings with IC M710, VSPE,? USB Signalink soundcard interface to ACC 1 for VOX PTT and TX/RX Audio, USB to clone port cable for FLDIGI and WSJT-X but it will also

> > >

Howard HRI windows visual studio Version 08 March 2017 v1 gives the IC M710 CAT control with WSJT-X v1.70 It makes the settings TEST CAT button turn green and reads and sets M710 frequencies etc.

Tom, I made some additions to Visual Studio HRI in the Kenwood TS2000 radio emulation department. Let me know if it works for you using WSJT on your Icom Marine Radio. Regards Howard

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* HRI.zip *Uploaded By:* Howard Z *Description:*

Howard I successfully use HRI's TS2000 emulation feature everyday to control my IC M710 with FLDIGI using RigCat settings and VSPE but I think WSJT-X uses Hamlib and like FLDIGI, WSJT-X's Hamlib

Tom, I recent new feature to Visual Studios version of HRI is where HRI emulates a Kenwood TS2000 radio via a Virtual comport. So, any software written to control a TS2000 can command HRI - and HRI

Hi Mike, What program do you use for JT65 and JT9? I tried without success a couple of times using WSJT-X by K1JT with and without HRI and could not get M710 rig control to work with it. It looked

Hello. My name is Mike and I have an IC-M710 I use for JT65 and JT9 for 60 m QSOs. I have an FTDX3000 but it dosnt tune to the latest 60 m bands. Hope to meet you on the Air. Mike 4X1LM

The Mars addon for Visual Studio's Ham Radio Integrator - it replaces the first three memory tables.

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* HRI-MARS.zip_AFMARSMN702.wzd *Uploaded By:*

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* HRI-MARS.zip_AFMARSMN702.wzd *Uploaded By:*

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* HRI.zip *Uploaded By:* Howard Z *Description:*

Sorry for my delayed answer but Internet access here is a little complicated and expensive. Thanks: I did what you say and start working better, but still with some issues, but i can use it now. I

I reread my comment and it confused me. So let me try again. Even though you are using the Clone pin jack set the IC M710 to use the d-sub in the Set Mode menu. Hopefully this works for your version.

Turn off ICm710. Press and hold "Function" and "1"? while powering back up again. Try "d-Sub REMT-IF" selection not Pin or clone. I know you are using the clone jack but this is what works for me. It

Roberto, I do not own an Icom Marine Radio, and have never even seen one in person.? Testing has been done by others to get HRI Visual Studios version working right with ICOM Marine Radios.? Tom has

Hello Howard: I'm amateur radio operator for 25 years now, my calls are CO2KL (Cuba extra class) and KM2KL(USA extra), my main interests are DX and contesting. This is my first post, I finally build

Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the [email protected] group. *File:* HRI.zip *Uploaded By:* Howard Z *Description:*

I think it makes sense to use 64bit software (when available) for a 64bit windows machine. In the case of device drivers like VSPE it is probably necessary. Howard -- Sent from my Android device with