开云体育

Hi Roy Thanks, I have now made an external lead screw crank. Let see what happens after 144 teeth cuts on a 3.465 inch ? wheel . Johannes Lavoll.

I am put a Milling Attachment on mini lathe that post photos there milling attachment. I have a new copy of Tiag type milling attachment. From Walmart. Look how did on Littlemachineshop.com. They made it offset why? I have this since Nov 2023 from Amazon and just getting around to installing on the lathe. I have look putting on compound but that is unstable so going to put on the cross slide like others have done on internet but it always great even if bad. Dave FYI I finished rotary table. Nice light easy to use and setup. e

Sorry, I wrote the message on the web page and i sent it too quickly. Here's it again : Hi, I've some trouble adjusting the clearance of the headstock bearings on my lathe. It's a WBL210 Weiss lathe ; max Dia 200mm, 300mm between centers, roughly a 8x12" lathe of the same design as the 7x12 ones. The surface finish was not as smooth as expected: even with shallow pass with slow motion. It was looking like a ~2mm pitch thread with a very low roughness pretty lower than 0.1mm. Probably the leadscrew pitch amplified by the gear train and some play in between the spindle bearings. Tightening the nut at the end of the arbor improved the situation but I couldn't manage to tighten it farther. The bearings seemed to be blocked by something. The drawing doesn't show any obstacle however. the bearings are 30206, tapered roller type. On to the other hand, 6 months ago I attempted to troubleshoot the spindle of my milling machine (model VM18L from the same manufacturer), ending by tuning the deep groove bearing clearances. It went the same way as the lathe. But since I didn't notice any discrepancy, I let it as it was and remounted the spindle. Several times, I've replaced tapered bearings on the wheel hubs of my cars without any extracting issues. They went well adjusted but not needing any great force to get them. I assume that the accuracy of a machine spindle being greater than a car's hub one, leads to a tighter adjustment. But, does it really need an extractor or is that a specificity of this manufacturer or even a bad quality level ? I found some clues on https://www.arceurotrade.co.uk/machineguides/Mini-Lathe-Angular-Contact-Bearing-Change-Guide.pdf. The bearings are 6206 deep groove or 7206 angular contact ones. The procedure uses both an extractor or a press but doesn't specify the force. I'm puzzled by the fact that I can't manage to tighten a bit more the nut because, normally, the external bearing should slide against the shaft otherwise it should be impossible to adjust the clearance. Please, may a specialist bring some light over all of this and/or provide other URL to relevant information ? TIA

I have got a C1900 "Guhl & Harbeck , Hamburg" pencil sharpener for restoration . Jupiter 1 Some screws are missing, and before I force in some modern ISO screws; Had Germany their own screws size 100+ years ago? I cannot find a " pencil sharpener IO group" , so I am asking you. New screws can easy be made with a 7x12 lathe ? Johannes Mexico

Hi guys. Sorry to come to this a bit late, I have 2 points though. * I’m not sure what the problem is, as anyone can add OT to the title, as I have done. So why the continuing debate ??? * I am amazed at some of the replies, not only to this but others as well. Where part of the reply is in understandable English and the rest is gobbledygook !!! I can understand and forgive differences where clearly English is a second or third language. But where part of the message shows the writer understands English, I despair. Doesn’t anyone read through and correct any more ? Ellis I forgot rotary table. If rotary table goes a mill it is OT. But if goes Mini lathe it is $&#^$ I guess it depends on if you interested read a about putting on a mini lathe if on topic or off. If do not like what they wrote then write moderators and say OFF TOPIC and ask to have it delete post so no has anything thing to read. The bottom for group to be interesting is have something to read about and better to comment on too. In November of 2023 I finally purchased a mini after reading about mini lathes since 2005. The resoan thinking a mini lathe in 2005 changed by time purchased. I chose to write about here and gave everyone here some read and write about. No one goes out buys a lathe every month. My first was a garulatoin present it only down payment on a $10,000 today same lathe cost $80,000 had for over 30 years. My next had for 20 years. The point is most do not go out and buy new lathe very often. So hard for very here to say a lot . So we all here need more than jest the mini lathes to talk about or this would a very slow group Dave

Here mockup of chuck on rotary table. Note 3" barstock for chuck adapter. The table is only 3" diameter The chuck 1.89" [48 mm] for small work FYI I 5" for larger work too Dave

The title is clear. I'm fed off this useless topic. Thank you. _._,_._,_

MAYBE CREATEED A UNDTHER GROUPE LIKE DIY FOR OFF TOPIC INTERROGATION LIKE EXEMPLE WHAT KIND OF GLUE USE FOR PLASTIC OR GLASS IN STAINE GLASS WORK WE ALL HAVE SOME OTHER INTEREST IN DO IT YOURSEFT AND WE PROBALY ALL NEED HELP FROM OUR METAL LATE GROUP JACK 5 47 71 QUEBEC CITY CANIVAL CITY https://canotaglaceexperience.ca/en/?gad_source=5&gclid=EAIaIQobChMIt7PUyMfVigMVkmZHAR3pJCfPEAAYASAAEgI5q_D_BwE MY SUN IS THE BEST INTRUCTOR YOU CAN FIND A REAL CHAMPION

Here is a 4 jaw chuck on a hand drill. Looks like fun and trip say to hospital staff .

Just a new 4 jaw chuck for rotary table 48mm dia. Nice size for small parts. It is not turning just light work on the 3" rotary table. Dave

I just purchased new rotary table and remembered that clock builders always what a 59 tooth gear made. This can be done on a mini lathe and a 36 worm gear 3" rotary table. Found a index chart use bs plates

I purchased a 3" Rotary Table at Christmas and have diving chart. Now looking at indexing.

Any do this Machine shop in Armoire's? This probably the new frontier for hobby. 1) Low cost 2) Space saving 3) Easy to move 4) Low cost in materials [COLOR="#669900"] I first look at mini as just a ???? After for over year it is nice. I changed because needing to downsize. With a few upgrades like a good tool post made great lathe. [/COLOR] Then later talking to son lacking space. So then we look hobby Armoire. He looking at other hobbies. Has any one did this or seen done? Dave

Hey folks , I have this old Milwaukee porta band that has ben hanging out since i retired . It's a lot heavier that I remember them being . Have any of you come up with a bench or even a free standing setup that will let ya use a porta band like a cut off saw . I'm looking for ideas, pics , things that didn't work . thanks animal

Menards (in the USA) today had the flexible LED goose neck lights on sale (7W) for $3.99 each. I just ordered 20 of them for my shop equipment. They are selling fast so I thought I would pass it along in case come one here is looking for equipment lighting.. https://www.menards.com/main/lighting-ceiling-fans/indoor-lighting/lamps/table-lamps/flexible-gooseneck-led-lamp/68769g/p-1642874340851661-c-7497.htm