开云体育

Gene, Thank you four the suggestion, I have not given any attention to the tuner...this is the first suggestion thus far that included the tuner. I will be giving it a try, and will get back to you.

Gene, I gave the tuner in/out a try and no change. Funny thing, in the CW mode I can operate the strait-key and get the side tone, but no transmit. Nothing changes, it acts like a code practice

Could possibly be a microphone problem try the mox with the microphone unplugged GENE MITCHELL. Kc0mqg TACTICAL.RADIO.GEAR@...> wrote:

Gene, Interesting suggestion. I will give it a try tomorrow. Thank you for your suggestions, much appreciated. Kind regards, Christopher wrote:

I sure do appreciate you guys hijacking a thread I started and going back and forth.? A real stand-up move.

Gene, The microphone was disconnected, and nothing changed when the MOX was activated, the ERROR came on. So I guess we are out of options? The radio is extremely clean, and looks almost like a new

Hello group I am new here so please bear with me ? I have a FT-920 from a silent key who was actually a friend of mine (KV4DP) I took the rig to? sell for his wife (also a friend), but I ended up

Hello group I am new here so please bear with me :) I have a FT-920 from a silent key who was actually a friend of mine (KV4DP) I took the rig to? sell for his wife (also a friend), but I ended up

Morning Question may have been asked in the past but nothing came up with a search.? What were the production years of the FT-920?? My serial number is 9Fxx.? So I believe that to be April 1999.?

Steve While I do not have the answer to your question, I would like to take it farther.? If I understand the 920 manual, the YF-116A/INRAD #710 filter is required for AM transmission.? So if you put

Basic Issue; I am using the Yaesu FT-920 with a 9DB to USB cable to control my rig via Ham Radio Deluxe software.? All is well.? The various elements work well so I am comfortable that the cable I

I want to use the Signalink external sound card unit with my 920 for digital work.? I want to interface through the 5 pin din connector on the back of the radio.? The Signalink cable to pair the

Thank you everyone for all the dialog and support to my queries and posts.? The Signalink is in hand and I clearly over thought this project.? The pin out of the signalink RJ-45 connector s obvious

My FTdx-3000 has the blinking transmit light issue.? I have factory reset the radio several times, left it unplugged for days, disconnected everything to insure some external source was not keying

I was going to use the 13.5V output (J2001) from the back of the 920 to power an Ameritron ARB-704 amplifier/radio interface.? I have no power at jack J2001.? The Op manual says the connection is

Well the hunt is over.? After numerous returns to scour the board for Q2037 I found it.? It is located right in front of the rear key jack and the Pdl-Key switch.? Looks like it is a through board

Hi I am trying to use the external output for speaker (rear) to pass the output signal through an AUTEK QF-1 Audio Filter and then split the output signal either to an external speaker or a

Hi all, im wanting to know if it's possible to use my ham antenna as a sdr receive antenna and also if i can connect the same antenna to my yaesu frg7 Am i right in thinking that there is no antenna

Hello to All, HNY to everyone. Please I have an issues with my Yaesu FT-920. If I try to decrease the VFO using the Shuttle Jog ( I mean the inner VFO knob ), the frequency instead to Decrease it

If you turn it all the way either way it will tune rapidly if you turn it slightly it will tune slower hope this helps this is what mine does anyway GENE MITCHELL. Kc0mqg