¿ªÔÆÌåÓý

Re: Mode switching problem or normal operation ?
I warmed up the computer and asked it. Says a 90c is 600hz. If that works for you I have one. Dave
By Dave Bohlen · #401 ·
Re: Looking for a 500 HZ cw filter or workaround
Hi Bob. The 90c is the cw filter for the 301. I¡¯m not finding the spec on that straight away but I think it is 500hz. I have plenty of them and will trade with you. Confirm the band width. 73 Dave
By Dave Bohlen · #400 ·
Looking for a 500 HZ cw filter or workaround
I have installed in my radio a 250HZ cw filter, 8999.3 khz does anyone have a 500HZ filter they would like to sell or trade for the 250 hz filter I have?? Robert KH2BR
By Robert Holsti · #399 ·
Re: Mode switching problem or normal operation ?
Turning the anti trip did not work, swapping out the vox unit board did not help so today I will spend my time tracing wires. Robert KH2BR
Re: Mode switching problem or normal operation ?
Make sure the anti trip is up.
By n0eds@... · #397 ·
Re: Mode switching problem or normal operation ?
I soaked the mode switch with Deoxit and that did not fix the problem. I turned the vox gain all the way down and that did not help? BUT !!! ,,,? I discovered what is causing it. When the? CW key
By Robert Holsti · #396 ·
Re: Mode switching problem or normal operation ?
Hi Robert. That is not normal, I would suggest you to look for what is wrong. I have 2 FT301D and none of them are doing what you are describing. Best 73 Jo?o Paulo Ribeiro CT2HZF No dia 01/06/2024,
By Joao Ribeiro · #395 ·
Re: Mode switching problem or normal operation ?
Is the VOX gain turned all the way down?
By n0eds@... · #394 ·
Mode switching problem or normal operation ?
When I switch from CW mode to USB, The t/r relay momentarily energizes and releases and the relay on the blanking unit energizes and de-energizes. When I switch from AM to CW it seems like the t/r?
Re: looking for parts. FT301s analog face plate and PB1433 rf board
Are you still looking for parts? -- Dave Bohlen
By Dave Bohlen · #392 ·
Re: Removing FT-301 VFO mechanism ?
If you go as far as to remove the VFO replace the bearings and grease. Chump change and standard bearing. Easy to come by. Just one more thing that it is not. -- Dave Bohlen
By Dave Bohlen · #391 ·
Re: From bad to worse
I used to sell them and probably still have one as well as the stabilizer. Elcon sells them. They're great. One of the first things I do with a 301 when it comes through is yank out the display and
By Dave Bohlen · #390 ·
Re: Removing FT-301 VFO mechanism ?
Oh, Great Fred thank you. I¡¯m used to radio. You say something, the other person says something at least copy or over. But I guess the web is not like radio. My first time on a web site. Then
By Dave Bohlen · #389 ·
Re: Removing FT-301 VFO mechanism ?
Hi All your message are posted on the Yaesu site. Fred -- Sent from Thunderbird mail ....
By Fred, N1DEC · #388 ·
Re: Removing FT-301 VFO mechanism ?
Hey, great thank you. Did the tip on the bumpity bump VFO go through. Had a couple of those. Hi hi Dave -- Dave Bohlen
By Dave Bohlen · #387 ·
Re: Removing FT-301 VFO mechanism ?
Yes.. Sent from my iPhone 7
By Fred, N1DEC · #386 ·
Re: Removing FT-301 VFO mechanism ?
Did this go through? Dave -- Dave Bohlen
By Dave Bohlen · #385 ·
Re: Help
Are you talking to me? I¡¯m new to computers and not doing real well. I do enjoy the 301¡¯s and have about 20 of them with lots of parts. Please let me know if this went through. Thank you Dave
By Dave Bohlen · #384 ·
Re: Help
Can't help it if you know so much more than the rest of us! ;-) It's been at least 10 years, and I have a '301S that I've slowly been bringing back from the dead.... It now receives fine, but
By Paul Ellis · #383 ·
Help
Can anybody help me respond to questions? Please. Dave -- Dave Bohlen
By Dave Bohlen · #382 ·