开云体育

PCB - GCODE ICAN'T OPEN-PERMISSION DENIED

#eagle #gcode

richi richardo All Messages By This Member #7997 dear All, I am new on this topic and have read most topic in regards of pcb-gcode on eagle. yes i am also facing the same problem, i could not able to solve this on eagle. is there any one can assist me? ? when i am putting the path for Ulps directory, later i am start eagle from begining again, try to open the board and run the ULP Button but appears like this : So after that i do close the warning window and it appears PCB Gcode window but with empty file coloumn as shown here : just like that, and after i press ACCEPT button,.... well,.. nothing shown anymore, and just gone,... no continuity of the result and i am remain on confusion,.. have tried to google from any sides of the world but i could not able to find the good information, and now i am finnaly reach this group with full hopes somebody can give me help to solve this issue. Many thanks in advance for any ones who can try to help me pleaseeee... pleaseee.... rc-man
chrisga63 All Messages By This Member #7998 Good evening to you. Pcb-gcode 3.2.6.4. works well with me with the older version of Eagle 7.7.7. with the newer versions it presents to me exactly the problem you described. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?chris Στι? Παρασκευ?, 20 Σεπτεμβρ?ου 2019, 04:05:17 μ.μ. EEST, ο χρ?στη? richirichardo via Groups.Io <richirichardo@...> ?γραψε: dear All, I am new on this topic and have read most topic in regards of pcb-gcode on eagle. yes i am also facing the same problem, i could not able to solve this on eagle. is there any one can assist me? ? when i am putting the path for Ulps directory, later i am start eagle from begining again, try to open the board and run the ULP Button but appears like this : So after that i do close the warning window and it appears PCB Gcode window but with empty file coloumn as shown here : just like that, and after i press ACCEPT button,.... well,.. nothing shown anymore, and just gone,... no continuity of the result and i am remain on confusion,.. have tried to google from any sides of the world but i could not able to find the good information, and now i am finnaly reach this group with full hopes somebody can give me help to solve this issue. Many thanks in advance for any ones who can try to help me pleaseeee... pleaseee.... rc-man Attachments: pCB-GCODE PROBLEM.png CB-GCODE PROBLEM.png
John Johnson All Messages By This Member #7999 开云体育 The `storage.nv` file is a file used to save settings for the program. It looks like yours was previously saved at the root of the C: drive, or pcb-gcode is unable to find the file. You can look around in the directory where you installed pcb-gcode and see if there is a `storage.nv` file anywhere within. If so, try copying it to `c:\`. toggle quoted message Show quoted text On 20 Sep 2019, at 14:22, chrisga63 via Groups.Io wrote: Good evening to you.Pcb-gcode 3.2.6.4. works well with me with the older version of Eagle 7.7.7.with the newer versions it presents to me exactly the problem you described. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?chris Στι? Παρασκευ?, 20 Σεπτεμβρ?ου 2019, 04:05:17 μ.μ. EEST, ο χρ?στη? richirichardo via Groups.Io <richirichardo@...> ?γραψε: dear All, I am new on this topic and have read most topic in regards of pcb-gcode on eagle. yes i am also facing the same problem, i could not able to solve this on eagle. is there any one can assist me? ? when i am putting the path for Ulps directory, later i am start eagle from begining again, try to open the board and run the ULP Button but appears like this : So after that i do close the warning window and it appears PCB Gcode window but with empty file coloumn as shown here : just like that, and after i press ACCEPT button,.... well,.. nothing shown anymore, and just gone,... no continuity of the result and i am remain on confusion,.. have tried to google from any sides of the world but i could not able to find the good information, and now i am finnaly reach this group with full hopes somebody can give me help to solve this issue. Many thanks in advance for any ones who can try to help me pleaseeee... pleaseee.... rc-man Attachments: - pCB-GCODE PROBLEM.png - CB-GCODE PROBLEM.png
richi richardo All Messages By This Member #8000 hI jOHN, Thanks for the reply, i am still try to figure out this, and by installing the eagle version 7.7.0, yes I can successfully install it, but when i am running it keeps producing G Code, showing the View and poop up windows said " after you finish viewing this window please close back the window". later when i am close it, nothing happened again, i am trying to fidn where is the G Code file being produce in my Eagle Folder, but no found anything about this G Code. Do you have any idea, why it;s behave like this ? Regards, Richi Richardo On Friday, September 20, 2019, 07:29:34 PM GMT+1, John Johnson <john@...> wrote: The `storage.nv` file is a file used to save settings for the program. It looks like yours was previously saved at the root of the C: drive, or pcb-gcode is unable to find the file. You can look around in the directory where you installed pcb-gcode and see if there is a `storage.nv` file anywhere within. If so, try copying it to `c:\`. toggle quoted message Show quoted text On 20 Sep 2019, at 14:22, chrisga63 via Groups.Io wrote: Good evening to you.Pcb-gcode 3.2.6.4. works well with me with the older version of Eagle 7.7.7.with the newer versions it presents to me exactly the problem you described. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?chris Στι? Παρασκευ?, 20 Σεπτεμβρ?ου 2019, 04:05:17 μ.μ. EEST, ο χρ?στη? richirichardo via Groups.Io <richirichardo@...> ?γραψε: dear All, I am new on this topic and have read most topic in regards of pcb-gcode on eagle. yes i am also facing the same problem, i could not able to solve this on eagle. is there any one can assist me? ? when i am putting the path for Ulps directory, later i am start eagle from begining again, try to open the board and run the ULP Button but appears like this : So after that i do close the warning window and it appears PCB Gcode window but with empty file coloumn as shown here : just like that, and after i press ACCEPT button,.... well,.. nothing shown anymore, and just gone,... no continuity of the result and i am remain on confusion,.. have tried to google from any sides of the world but i could not able to find the good information, and now i am finnaly reach this group with full hopes somebody can give me help to solve this issue. Many thanks in advance for any ones who can try to help me pleaseeee... pleaseee.... rc-man Attachments: - pCB-GCODE PROBLEM.png - CB-GCODE PROBLEM.png
chrisga63 All Messages By This Member #8001 The file of g-code entered into the file of? circuit and psb board? Take a look at the photos below to understand. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?chris Στι? Τρ?τη, 24 Σεπτεμβρ?ου 2019, 03:28:58 μ.μ. EEST, ο χρ?στη? richi richardo via Groups.Io <richirichardo@...> ?γραψε: hI jOHN, Thanks for the reply, i am still try to figure out this, and by installing the eagle version 7.7.0, yes I can successfully install it, but when i am running it keeps producing G Code, showing the View and poop up windows said " after you finish viewing this window please close back the window". later when i am close it, nothing happened again, i am trying to fidn where is the G Code file being produce in my Eagle Folder, but no found anything about this G Code. Do you have any idea, why it;s behave like this ? Regards, Richi Richardo On Friday, September 20, 2019, 07:29:34 PM GMT+1, John Johnson <john@...> wrote: The `storage.nv` file is a file used to save settings for the program. It looks like yours was previously saved at the root of the C: drive, or pcb-gcode is unable to find the file. You can look around in the directory where you installed pcb-gcode and see if there is a `storage.nv` file anywhere within. If so, try copying it to `c:\`. toggle quoted message Show quoted text On 20 Sep 2019, at 14:22, chrisga63 via Groups.Io wrote: Good evening to you.Pcb-gcode 3.2.6.4. works well with me with the older version of Eagle 7.7.7.with the newer versions it presents to me exactly the problem you described. ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?chris Στι? Παρασκευ?, 20 Σεπτεμβρ?ου 2019, 04:05:17 μ.μ. EEST, ο χρ?στη? richirichardo via Groups.Io <richirichardo@...> ?γραψε: dear All, I am new on this topic and have read most topic in regards of pcb-gcode on eagle. yes i am also facing the same problem, i could not able to solve this on eagle. is there any one can assist me? ? when i am putting the path for Ulps directory, later i am start eagle from begining again, try to open the board and run the ULP Button but appears like this : So after that i do close the warning window and it appears PCB Gcode window but with empty file coloumn as shown here : just like that, and after i press ACCEPT button,.... well,.. nothing shown anymore, and just gone,... no continuity of the result and i am remain on confusion,.. have tried to google from any sides of the world but i could not able to find the good information, and now i am finnaly reach this group with full hopes somebody can give me help to solve this issue. Many thanks in advance for any ones who can try to help me pleaseeee... pleaseee.... rc-man Attachments: - pCB-GCODE PROBLEM.png - CB-GCODE PROBLEM.png Χωρ?? τ?τλο.jpg
Mark Duquette All Messages By This Member #8019 put pcb-gcode in the documents folder and follow the instructions when you open the script.

Previous Topic Next Topic