开云体育

Hi José, Unfortunately, I don't have an answer for you. It sounds like Art has covered a lot of ground with you already. Maybe these general strategies will be helpful. I could be wrong, but it

Jose, I was hoping someone else with more experience than I would jump in and try to help you. Without 'looking over your shoulder while your trying to do this', I am running out of ideas to try. But

Art Thanks again for your help. I do holes my friend. I draw tracks that you call wires but are only my English approach. Then the cnc cuts around it. And I did that with your help using 46 layer. So

Jose, Sorry for the delayed reply, but sometimes, things happen! Anyhow, I am courious as to the type of info that you want to mill? Because as noted in the manual, Text will be engraved, and "Wires"

Hi fellows I'm trying to milling on 46 layer but in gcode setup Eagle shows allways text option. Instead I choose milling and run but only get a text file and never a top milling file. Can you please

I have a fully functioning MAXNC 15 CL for sale.? Includes the mill which is 4 axis, the software, and DOS computer.? Also loaded on the computer is Autocad 13 with software.? I am in east Texas

Jose, Sorry, but this time I don't have a clue as to the situation. I am still using V6.4 for various reasons and therefore am not familiar with problems that may be associated with that version.

Hi Art Sorry to bother you again but a issue with Eagle 9.6.2 that I am using now does not let me doing milling on layer 46. I'm trying to do some adjustments on my panel (no text included) and after

Jose, I am not familiar with the "Nugget Mills" but am glad you have it working for you. Good luck and am glad we were able to give you some assistance. Country

Dear Art I assume in my falty point of view that this software for technical drawings works on vector lines as Autocad. Again your knowledge and good will help me. But this tricky things are a always

Jose, The first thought is, have you done the text in vector format? From the manual: "Text Generates gcode to engrave any vector text that is on the Milling (46) layer." To check, on your board, go

Dear Art Thanks again for your help. But my sad story didn't yet finished. I use a old laptop HP with a centrino duo and windows 8.1 to do this job and connect with my cnc. But when I tried to make

Jose, Glad to hear you got that one fixed (or at least working)! Now to your text problem. Click on the 'I' (info) button on the toolbar and then click on the text that you want to change layer. This

Hi Art Thanks for your tip but perhaps because of my older Eagle version didn't work, so I created a new line between the objects and the drawing edge and it works : the newer line does not appear but

Jose, Don't worry about your English, your doing fine. Its a lot better than my Portuguese! If your elements are near the edge and not showing up, try moving them in a bit or change your Design Rules:

Hi Art Sorry for my poor English. Thanks again you help me a lot, I'm a basic level user of Eagle that is a freeware version and pcbgcode too but I follow your tips and my panel is almost running even

Jose, I am not familiar with your term "raws", but am assuming these might be "slots"? If so, you need to put them on the milling layer (46) and be sure in your setup to check the 'Generate milling'

Hi Ark Thanks for helping me. I'm using Eagle 7.5 and pcbgcode 3.6.2.4 on a few projects and it works great. This time I try to make a panel with some raws to install connectors. So I put some alone

Been there and done that, although with toner transfer. They turn out to be rather big, and I used copper ones, IIRC, not brass.? They're also not possible to put under SMT chips. I staked mine in

Since this great idea did not work out so well, i thought I'd share it. I've come to need to do double sided boards now because my projects need SMD devices, and vias.. I asked around and found that