¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
Re: errors of "error" models
#102: The Complete "Demystification" of the "VNA Measurements" Kind - Farewell Hello, Well, we arrived at last at The End of a rather long Road. The VNA gives to The Common User the Value: (g - o)*(l
By gin&pez@arg · #9073 ·
Re: Bi-Quad Antenna 430 MHz is this a good one? #calibration
Dave is correct. The SWR looks great, but a nice (short leaded) 50 ohm resistor would also look good. There's a commercial wire (HF) antenna out there that uses a big 'ole 50 ohm resistor at the feed
By Ron Bussiere <n4ue@...> · #9072 ·
Re: Bi-Quad Antenna 430 MHz is this a good one? #calibration
Certainly, the SWR looks excellent. Now, does it radiate? Dave - W?LEV -- *Dave - W?LEV* *Just Let Darwin Work* *Just Think*
By W0LEV · #9071 ·
Re: errors of "error" models
#101 : A Mechanical Proof of the Invariability of the Cross-Ratio Under the Moebius Transformation of G to g of a Two-Port Hello, Allow us, please, to inform you that we just uploaded a Mechanical
By gin&pez@arg · #9070 ·
Bi-Quad Antenna 430 MHz is this a good one? #calibration
Hi, I build a Bi-Quad Antenna for 430 MHz, measurements are on the photo, my question is this a useable antenna or is there something wrong? Thanks in advance. Regards ersoez
By @blackmagic · #9069 ·
Re: Signal Integrity Tips and VNA Measurements #tutorials
Also the following: https://www.keysight.com/us/en/assets/7018-05214/article-reprints/5992-1509.pdf https://www.keysight.com/upload/cmc_upload/All/Signal_Integrity_Measurements_Network_Analyzers.pdf
By Larry Rothman · #9068 ·
Signal Integrity Tips and VNA Measurements #tutorials
Copper Mountain Networks has the above ebook available at: https://www.microwavejournal.com/articles/33253-signal-integrity-tips-and-vna-measurements
By Gary W9TD · #9067 ·
Re: Why rg316 ?
Teflon also handles a good bit more heat. In case you plan to solder it to something.
By Bob KV4PC · #9066 ·
Re: Crystal measurements & QEX review
However, do not forget the time base accuracy is 0.5 ppm. Alan
By alan victor · #9065 ·
Re: errors of "error" models
CREDITS @Erik, PD0EK - 2 January 2020 - /g/nanovna-users/message/9053 previous : gin&pez@arg - 2 January 2020 - /g/nanovna-users/message/9055 Dear Erik, Well, we just
By gin&pez@arg · #9064 ·
Re: DFUseDemo
Would one of these inexpensive devices solve your problem? I bought one (just in case) but haven't needed to use it. https://www.ebay.com/p/4024997830
By W5DXP <w5dxp@...> · #9063 ·
Re: Crystal measurements & QEX review
I see in the review in the Jan/Feb 2020 QEX that the minimum resolution is 1 kHz and scanning a crystal might give a close approximation of its resonant frequency but not much else. I used nanoVNA
By David J Taylor · #9062 ·
Re: Calibration standards
Hello Ed SDR-Kits has both SMA and BNC calibration kits which is documented. Soon there will also be 5 parts N calibration kit The 4 parts BNC and N kit is universal as being both male and female.
By Kurt Poulsen · #9061 ·
Crystal measurements & QEX review
I see in the review in the Jan/Feb 2020 QEX that the minimum resolution is 1 kHz and scanning a crystal might give a close approximation of its resonant frequency but not much else. I used nanoVNA
By Nick Kennedy · #9060 ·
Re: Calibration standards
Look here /g/nanovna-users/wiki/RF-Calibration%2C-considerations%2C-notes -- NanoVNA Wiki: /g/nanovna-users/wiki/home NanoVNA Files:
By Erik Kaashoek · #9059 ·
Re: errors of "error" models
ann : next-to-come : the complete "demystification" of the "VNA measurements" kind
By gin&pez@arg · #9058 ·
Re: errors of "error" models
#100: Any 2-port Introduces Relations of Moebius Transformation Between g an G Hello, Allow us, please, to present these two ways, g is a Moebius Transformation of G, and G is a Moebius Transformation
By gin&pez@arg · #9057 ·
Calibration standards
I'm a newbie and my only experience with VNAs is borrowing a friend's AIM 4170 from time to time for antenna measurements. I recently purchased a NanoVNA-H and am waiting for it to arrive. I was
By Ed Jones <cuisinartoh@...> · #9056 ·
Re: errors of "error" models
@Erik, PD0EK - 2 January 2020 - /g/nanovna-users/message/9053 Dear Erik, Thank you very much for the attached paper. Yes, indeed, we found and took a look at it some months ago.
By gin&pez@arg · #9055 ·
Re: Alibaba ordering
DISCLAIMER - I have no pecuniary interest in Gigaparts or Gigaparts.com Actually I ordered a NanoVNA from Gigaparts... (claim of consistency and quality versus china direct) Received it in 2 days...
By Larry Macionski · #9054 ·