开云体育

#83 : On the Doubtfulness Hello, Allow us, please, to announce that, as it seems, we may just found the deep source of doubtfulness and in the following way : we thought that we had to think

Hugen, Is there going to be a selectable USB/serial port PC I/O mode for this version with the new uP? ThanksLarry On Fri, 13 Dec 2019 at 3:18 AM, hugen@...<hugen@...> wrote: I've made

Yesterday I received the Nooelec "Balun One Nine V2" and did limited testing. It uses a Coilcraft WB9-1 transformer, with a published 3dB bandwidth of .125-125MHz; interpolating the datasheet graph

From: nanovnauser@... my post code is ln95je,i put that and it says wrong format every time,tried it in caps too,same result,what should i put then? ========================================== My

Hi Kurt, I tried your latest How_to_display_delay_shift_for_a_cable_in_NanoVNA_saver.pdf method. Now I have many problems. I not understand what I do wrong, or what corrections/calibrations will be

hugen, The larger display size is great and if the > 50 dB dynamic range to 1500 MHz holds up in the final release then I'd say you have a winner. Does the larger flash_size allow you to increase the

On Thu, Dec 12, 2019 at 10:28 PM, <nanovnauser@...> wrote: my post code is ln95je,i put that and it says wrong format every time,tried it in caps too,same result,what should i put then?

I've made a new PCB for testing, it's working well now, but At the moment ADC1 can't read VBAT data correctly, and I can't get into DFU mode through the menu yet, I haven't found the cause of the

my post code is ln95je,i put that and it says wrong format every time,tried it in caps too,same result,what should i put then?

http://deepelec.com/ I have purchased it from them without any hassle, and with complete tracking online.

On Sat, Nov 16, 2019 at 12:59 PM, Oristo wrote> Oristo, I picked up a bridge from the eBay link above. The build quality is poor and the 2, 100 ohm resistor pairs are each not in parallel. So even

Hi Herb, I think Erik or QRP (and maybe Rune) will have to answer that more accurately than me, as what I wrote was my interpretation of their explanation in a forum post waaaay back in October some

On Wed, Dec 11, 2019 at 12:46 PM, "[email protected] Notification" <[email protected]> wrote: * /NanoVNA_Console_Commands_Dec 9-19.pdf (

On Thu, Dec 12, 2019 at 12:55 PM, <nanovnauser@...> wrote: ,,, i enter my post code,it just says its in the wrong format,ive tried every which way with no luck,im tearing my hair out,anyone any

Hi David, the NanoVNA-F is designed by a Chinese ham, so what you want to avoid is a clone - not a Chinese one ;-) The original NanoVNA-F is available at http://deepelec.com/ - and only there, as I

My FCU refuses to honor charges on my card to Aliexpress. I no longer tempt ordering from them. Three times. Same results. Likely due to Chinese vender? Dave - W?LEV -- *Dave - W?LEV* *Just Let

After using the original with the 2.8" screen, I'm looking to order the 4.3" unit. As best I can gather, there are three units available all with different external presentations. These are: 1)

ive found a screen the same as hermans 3.2 inch on aliexpress(thanks for the link herman),however it goes ok trying to buy it untill i enter my post code,it just says its in the wrong format,ive tried

Hi, Like others, I am having problems with Python PyQt5 etc. I am trying to get NanoVNA to run with a Raspberry Pi 4 with very little success. Works perfect on the Mac Pro. Do you or others know of a

Garry, Thanks, I may have formulated unclear but what you state is what I meant. Uncertainties in M act as "error bars" making it uncertain where you are in the graph, Uncertainties in the calibration