¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
Re: Brand new user here
i use a pen cap or a tooth pick its a resistive screen so anything pointy and non metalic will work even a #2 pencil
By k9wkj · #8034 ·
Re: connector swap
Photos? On Sun, 8 Dec 2019 at 1:49 PM, Nulluser00@...<Nulluser00@...> wrote: I mounted my NanoVNA on an Budd aluminim cast box and use male SMA to male SMA to a female SMA to male BNC
By Larry Rothman · #8033 ·
Re: 1.5 GHz ??
Oh that's useful information. I have some simple measurements to do at 1.2Ghz, will give it a try.
By Cathryn Mataga (KE6I) · #8032 ·
Re: Brand new user here
Try your local computer store. I just bought a pack of 10 from Amazon for less that $& US. *Clyde K. Spencer*
By Clyde Spencer · #8031 ·
Re: nanoVNAPartner v0.17
I have this problem also. -- Cheers, Ed Humphries, KT4ED
By Ed Humphries · #8030 ·
Re: The T-Check confusion
Hi Herman First of all it is not the mini-VNA it is the DG8SAQ VNWA. Sorry these kind of measurements is only possible with a VNA having 10/12 term error correction facilities. NanoVNA is not able to
By Kurt Poulsen · #8029 ·
Re: 1.5 GHz ??
No configuring necessary.? Simply key in the frequency. By default it comes up with 900 MHz but you can ask for up to 1.5 GHz and you will get it. Bob
By Bob Albert <bob91343@...> · #8028 ·
1.5 GHz ??
I have read elsewhere than the NANOVNA will operate to1.5 GHz. Is this ture? If so, how do I configure it to do so? -- *Dave - W?LEV* *Just Let Darwin Work* *Just Think*
By W0LEV · #8027 ·
Re: The T-Check confusion
Please, can you not make the PDF with plots of the NanoVNA, and not the Mini-VNA ?
By ON1BES · #8026 ·
Re: nanoVNAPartner v0.17
Not a problem with Windows10 64 bit here.
By ON1BES · #8025 ·
Re: errors of "error" models
Hello again GIN&PEZ I would like to continuing following your work, but I think you are expecting much mind reading on my part for me to meet that objective. I am able to infer some information from
By Gary O'Neil · #8024 ·
Re: Brand new user here
Here's a 'free' idea that works. Take an old (2 piece) ball point pen and replace the ink tube, with a small diameter piece of wood, sharpened to a point. Chop stick, wood 'Q tip', (which is what I
By Ron Bussiere <n4ue@...> · #8023 ·
Re: Brand new user here
My 'stylus' is an old metal drafting pencil, the back side, all metal.? It's perfect. Bob
By Bob Albert <bob91343@...> · #8022 ·
Re: New version of NanoVNA-Saver: 0.2.1
Hi Rudi I insert my comments below -----Oprindelig meddelelse----- Fra: [email protected] <[email protected]> P? vegne af reuterr@... Sendt: 8. december 2019 20:05 Til:
By Kurt Poulsen · #8021 ·
Re: New version of NanoVNA-Saver: 0.2.1
Hi Rudi, I loaded to Sim Smith Chart your s1p data file. I see some calibrations and/or nanovna errors. The circle not spiral to centre point simmetrically. I subract 31,22cm RG-174 cable from
By pgc1682@... · #8020 ·
Re: Brand new user here
The local Dollar Tree has them.? Probably most office supply stores would have them too.? They are also available on Ebay.
By Jim Allyn - N7JA · #8019 ·
Re: Brand new user here
Walgreens has stylus - small rubber on one end, take the cap off and you have a ball point pen. Dave - W?LEV
By W0LEV · #8018 ·
Re: errors of "error" models
Hello again GIN&PEZ -- 73 Gary, N3GO
By Gary O'Neil · #8017 ·
Re: Brand new user here
A small not sharp wooden stick works also. -- NanoVNA Wiki: /g/nanovna-users/wiki/home NanoVNA Files: /g/nanovna-users/files Erik, PD0EK
By Erik Kaashoek · #8016 ·
Re: Brand new user here
Bob, Thank you.? That works! Ray, W4BYG
By Ray, W4BYG · #8015 ·