开云体育

During the "Chasing ghosts" series it was discovered that 8mA creates non-linearities. Can someone that has installed 0.4.0-3 do a S11 measurement of a 25 ohm resistor from 1 to 900MHz? -- NanoVNA

QRP and Oristo wrote: "it has larger font, so it cannot show full frequency and measured value result and cut-off part of the value" "4 calibration SAVE areas instead of 5. On the other hand, Hugen

Hi Herb - 4 calibration SAVE areas instead of 5. On the other hand, Hugen maintains code inline that is neither in edy555 nor QRP firmware, so presumably more responsive. Other space was cleared in

it has larger font, so it cannot show full frequency and measured value result and cut-off part of the value

On Mon, Nov 25, 2019 at 04:41 AM, Larry Rothman wrote: " …. Note large font on 4 traces now." ================================================= If the AA version now has 4 traces then, other than a

1) power and integration, given the goal of a BLE VNA sensor 2) toggling Pi Wi-Fi off/on between VNA scans could be problematic; as would leaving it on. 3) "(BLE support is still in the works,

Everyone keeps talking about (relatively) expensive solutions to get? a wireless connection from the NanoVNA. Why not just but a RaspberryPi Zero-W for $10US from Adafruit and use it as a USB Host to

Hi Rune, Again, I would like it very much when "uncalibrated" or? the description of the active calibration-file is shown in the MAIN window, to avoid confusion while working. Jos Op 25-11-2019 om

Hugen's updates from today's NanoVNA-H firmware release: 1.The absolute value of the linear format is displayed;?? 2.Si5351 default 8mA output;?? 3.The AA version shows 4 traces.?? Note large

The recently announced (for ~ US$20) Arduino NANO 33 BLE claims USB host support: https://www.arduino.cc/en/Guide/NANO33BLE Based on Nordic nRF52480 (which cannot natively implement USB host), this

Your standards could be significantly improved as follows: Short: Don't use wires, too much added inductance. instead use braid or a thin piece of sheet copper (with hole) pushed down flush against

Hi Rune, when you raise a nice fat pig from a small pig, there will always be someone who does not like why they are not smart enough. :? :? It was just a joke, sorry. 73, Gyula

same seller i ordered, fake tracking number which never showed any progress. But before the last day of delivery (Novemebr 19) I was not able to issue a? dispute and claim a refund . I did this on

and hugen79 a couple of hours ago! here..https://github.com/hugen79/NanoVNA-H/releases

edy_555 release... 0.5.1-20191123 couple of days ago Here.. https://github.com/ttrftech/NanoVNA/releases

Hey dr op 5QR5. Okay. That explains a lot :). But: I think a "X" for load last .cal file would be okay. A textbox can show the filename of last .cal file. What do you think?

Hello DE8MSH, Thank you for your comments and your suggestions! Currently, NanoVNA-Saver has no interaction with the calibration on the NanoVNA itself. The application assumes that you have a

Only non-inductive resistors are needed around the GHz, which must be soldered to the connector and cut off excess feet. The calibration on the images is appropriate for the shortwave. Calibrations

The nanoVNA-Saver does not automatically load previously saved data, but you can create a lot of calibration data yourself and download it as a calibration data before use. You can comment on the

Many thanks, Oristo, I really appreciate your work. Thank you all for the valuable information. This group is a real gem! 73 Ady YO2NAA