开云体育

Hi Ady This is already possible using https://github.com/qrp73/NanoVNA-Q/releases Not sure why delaying start is necessary; scans until pause are discarded. Only the final scan before pause is

That works when short and open results are similar and load signal is small. Small load signal is generally easy for resistance bridge at low frequencies, not so much for reflection bridge and higher

Hi Kurt - .. and another piece of the puzzle falls into place.. Thanks ever so much!

The very "short" one port equation does get meaningfully close, but diverges with frequency. I haven't computed the impedance deviation yet, so it's too soon to pass judgement. My spreadsheet is

thank you, I made a mistake during calibration, now the reading is good, have a good day Gilles

Hi Gilles, I assume you followed a calibration routine as documented. There is one in the file directory. See

hi, When I am doing a full calibrate O S L iso and thru. I get a -10.8 dB on log mag with the RG174 coax cable. on full RF span exemple: 28 to 30MHz or other frequencies range. channel select is

Rune, While you are at it is there any way to integrate an option so that the cursor data can be displayed in the appropriate graph display area similar to the data that you see on the real VNA

GIN & PEZ@arg; New results to please you all the more. I just replaced your mini equation: https://www.op4.eu/code/G-mini.c.gza.cc.by.4.0.2019.png with your even smaller equation as presented in Part

I'm using a Dell laptop at 1366x768, font size 8, 16:9 aspect ratio, Windows 10. I haven't had problems with the scrollbars being present or overlaying the taskbar since before nanovna-saver version

GIN & PEZ@arg; Excellent news to hear. Have you done any recent IEEE publication or presentations of the work you are presenting here, or have plans for presenting at any Conferences? -- 73 Gary, N3GO

Sam, Have a look at Classic Shell for your windows OS. It makes the start menus look like win7 and works quite well with the current win10 update.? ... Larry On Sun, 3 Nov 2019 at 4:41 PM, Rune

Hi Ady, That is why for version 2 hardware, folks are asking for Bluetooth or wifi control of the unit.? ... Larry On Sun, 3 Nov 2019 at 3:48 PM, Ady, YO2NAA<yo2naa@...> wrote: Hi all,

Hi Sam, I think maybe the Windows 10 task bar is a few pixels more than the Windows 7 one? I'll try to see if I can find a few pixels in the interface so it will fit - it should be possible :-) It

#71: Good News : (1) DEP was Restored and Maxima is still Working in these 2 cases : [WXP64P&SP2] and [W7P64], (2) Maxima Worked Immediately in [W8.1P64] @Oristo - 2 November 2019 :

Hello again Rune, Once I figured out how to hide the taskbar (face palm!) it fits. It would be nice of it would fit without hiding the taskbar though. 73, Sam Reaves ARS W3OHM Owner and Moderator of:

Hi Rune, I am using Windows 10 on a HP15 f162dX 15" screen 16:9 aspect ratio laptop. Data is here: https://support.hp.com/us-en/document/c04530928 I like is because it's a Intel I3 is lightweight and

The calibration routines start at line 1034 https://github.com/ttrftech/NanoVNA/blob/master/main.c -- Erik, PD0EK

Got bitten too it seems. Hopefully I can get a refund via Mastercard. I think this may be protected. As for the scammer, pillory.

I was fortunate enough to get some high-quality PTFE (Teflon) coax (RG-174 sized) SMA to BNC jumpers - and these hold up much better, probably because they have a small piece of heat-shrinkable tubing