开云体育

Robin: Rather insensitive terminology here! "1) there is the odd Doll on this group as well as [far too many, /pro rata/] Guys” Chuck Young

Interesting video by W2AEW on this subject "How to tune a duplexer with a NanoVNA V2plus4 | is it possible?" https://www.youtube.com/watch?v=TbEK4v_3Xuo Roger

The attached image indicates you are measuring from 50 to 52 MHz, not 1.9 to 450 MHz. Dave - W?LEV -- *Dave - W?LEV* *Just Let Darwin Work*

Thanks, DiSlord for this! It's awfully close, and granted, for precision accuracy remember that we're comparing a $50-$75 device against oscilloscopes or spectrum analyzers which cost many times

My fw allow made internal 26MHz TCXO correction (see CONFIG->EXPERT SETTING->TCXO) Power on device, set 26MHz CW output Wait near 5-10min for device warm Measure output frequency Enter this value as

On 12/20/21 12:27 AM, Earle Wilkinson wrote: > Earle D Wilkinson > (6Y5EW) > > Home page: http://jamaicaham.org/ > Email address: earle.wilkinson@... > Echolink: 6Y5RA > > On Mon, Dec 20, 2021,

As i see log, no any card installed: This string mean Nano Ask for card, and no any answer - Check the correctness of installation in the slot, the card should be contacts to the board and completely

You have a transformer with 36:1 impedance ratio, and an 1800 ohm load.? You should see 50 ohms on the other side. That is pretty close to what you see.? What were you expecting?

Good afternoon. The same problem with saving to the card. Kingston 8Gb HC Card.

Jens, 1) there is the odd Doll on this group as well as [far too many, /pro rata/] Guys 2) for the technical question, imagine that there are *2* oscillators active, one at f?, one at f?+IF, where

Hello Guys, I've one question which puzzles me, and was unable to find information neihter in the forum nor in the Wiki. Since the NanoVNA outputs a rectagular signal which's harmonics are not

I see in NanoVNA-Saver screenshot frequency range 50-52MHz

Earle D Wilkinson (6Y5EW) Home page: http://jamaicaham.org/ Email address: earle.wilkinson@... Echolink: 6Y5RA wrote:

Hi All! I am now evaluating a 1:6 UNUN with NanoVNA that I bought quite recently. The UNUN is made of two stacked FT240-61 and 1.6mm copper wire with 100pF capacitor in the primary. To measure SWR, a

After connectiin to PC, NanoVNA must see as additional COM port, you can check this in device manager. If no additional ports in, check uncnown devices, and update drivers. For USB connection baud

Larry, Sorry to see that your post got hijacked and went off topic! I want to than you for the work you did putting this DiSlord updates document together. Very interesting to see how the firmware has

My document is NOT on that website. The owner of that website attempted to hijack my thread and drive views and probably advertising revenue for himself. On Sun., 19 Dec. 2021 at 4:34 p.m., Rick

Disadvantage - with more points you get a slower sweep time. Advantages - - with more points the step size for a given frequency range is smaller so you get more plotting "definition". When measuring

DisLord excuse me for using your post. I need a clue why Nanovnasaver will not connect to usb port on my win 7 machine. I have win-7 SP1 plus C++ and Net+ installed and I also ran the Cypress USB

You not install 32768 quartz for rtc If you not plane install it, remove battery, wait 10sec and put it back. This reset lse mode to lsi