开云体育

All, Where can I find the instructions on upgrading to the latest firmware version for the -F model and what is the latest version? Thanks in advance... Larry, K4MLA

Doug, I will try that tomorrow.... that’s one thing I didn’t check

Here is a second report on the effect of calibrating the NanoVNA on SWR and Return Loss measurements. This time a 20M dipole was used as the antenna. It was surprising to me to see how good the

Unless he signed a non compete contract while he was employed by you there is nothing that you can do. OSS project, anyone can sell their own copy/version.

I did some measurements today on a vertical whip antenna tuned for the top end of the 2M amateur band. I wanted to see the effect of calibrating the NanoVNA on SWR and Return Loss measurements? The

I'd say "Welcome to the world of open source. That's how it's supposed to work." The whole point of open source is that if someone thinks they can do better, they should have the chance to try. That

macOS Catalina Version 10.15.4 Rebooted to Recovery Mode Disabled SIP (csrutil disable) Restarted in "regular" mode device shows up as /dev/cu.usbmodem4001 Used NANOVnA to scope out antenna Rebooted

On Sun, Apr 26, 2020 at 01:46 PM, <reuterr@...> wrote: Hello DiSlord, Will you please so kind and provide your firmware version 0.8.4.4 also for the nanoVNA-H (not H4).

I have several CDE silver mica capacitors I ordered from Mouser, and have several more on back order. I bought leadless surface mount capacitors, but they also have leaded varieties. The ones I bought

Hello DiSlord, Will you please so kind and provide your firmware version 0.8.4.4 also for the nanoVNA-H (not H4). 73, Rudi DL5FA

On Sun, Apr 26, 2020 at 10:44 AM, Dick wrote: There must be something else as I cannot reproduce your results. ...... Trying to measure a 10 mH RF Choke, display bounces around from 190pH to 600pH. ..

Hi Herb, Good thing those banana adapters are OK for DC, I will opt for that method. I will need to measure some coils for end fed antennas and a coil in a trap, lets see what I can do. At 1MHz I

Hi DiSlord, Flashed your latest firmware 0.8.4.4, no problems sofar. Please find attached my results measuring the 50 Ohms standard , 50 Ohms standard paralleled by 50 Ohms and CH1, after calibration.

There must be something else as I cannot reproduce your results. Now, I am using a NanoVNA-F, but I can't see where that matters. Trying to measure a 10 mH RF Choke, display bounces around from 190pH

Dick 9:58am #12913 What settings did you use to get these measurements ? ===================================== Dick, No special settings. Just turned off the CH1 traces, set the frequency sweep from

What settings did you use to get these measurements ? Tnx, Dick, W1KSZ ________________________________ Sent: Sunday, April 26, 2020 8:33 AM To: [email protected] <[email protected]>

Luis, Most commercial LCR meters for less than $200 only measure inductance or capacitance below 1 MHz. Manufacturers specify the values of their inductors or capacitors at a specific test frequency,

I use XJW01 digital bridge 0.3% for measure R, L, C Measure C: 0,1 pF–10000 mF Measure L: 0,01 uH–1000 H Measure R: 0,0002 Ом–9,999 МОм If calibrate on good calibration standarts allow get

Hello team, Trying to understand a good method of measuring the inductance - lets say around 110uH - of a coil. Is the L/C method the best? Is there any direct method of measuring the L? Also, for L/C

You don't need to add a switch, just use the same jumper as I used which is the method the H4 uses and you only need to hold down the jog switch when turning on the Nano.?