开云体育

Hi David, Is the certificate something I must install or is it something the CUPS web server must install? John

Workaround/solution found.? Open .nbems folder, see file names FLMSGprefs.? delete that file.? When you restart FLMSG you will have to reconfigure your call sign and other configuration settings

I had to do a rebuild and can't get fldigi to control my FTDX10. Radio works fine using CAT in WSJT-X so I know USB communications will work. I am getting a good waterfall in Fldigi and PSK31 decodes.

Hi David, Thanks for getting back to me. Attached is the trace.txt file with the settings shown above. I do have polling enabled in the settings and perhaps the polling rate is set too high, but I

Hello John, This is probably due to Chromium insisting on using HTTPS but CUPS is using a self-signed HTTPS x.509 certificate. You can either choose to tell Chromium to trust and accept this local

I had cups running OK on an SD card before I switched to an NVMe device and mistakenly managed to overwrite my SD card.? I started over and am now running only on the official Pi NVMe ssd . Using the

Dave, Here is a curiosity question: I am running the current alpha code (4.2.06.15) now, but have seen this multiple line blurring effect going back a ways in previous versions. If I run fldigi on

The objective is to open a previously-received file and relay it.? I cannot open a file from file | open. file | folders, double click on a file - file opens in mousepad but not in the FLMSG window.

My two Pegasus died years ago.? I am surprised to hear of someone still using one.I will need to see the trace file output during Rx and Tx.? Set up flrig as shown here: After shutting down, send me

Hello, I am trying to get fldigi to talk with my PicoRX via its Kenwood TS-480 emulation but all that happens is that fldigi stalls until it runs out of retries I think. Has anyone had any luck

Just a bump for attention, don't know if there is a better place to post this to get noticed or not... If so, please let me know!

Re:- From: Mark, KE8NHT Ohio Date: Mon, 16 Dec 2024 19:25:21 GMT Do you have Config Settings> Misc > Save Parameters> AFC Control checked or not? I did notice at one point that it prevented changing

Szia Ervin, Yes, this is a great help, thank you. Lev -- Levente Kovacs Senior Electronic Engineer W: http://levente.logonex.eu

I have port audio checked and pipewire assigned to capture and playback. I try it a bit and see how it works. If I have trouble I'll change to pulse audio. Ron NY3J

Thank you that did it.? In KDE, in the Discovery app, settings, checking Sources, did the trick. Once I did that 'sudo apt build-dep fldigi'? worked. Instead of aptitude I have just been using apt,

Running fldigi 4.2.06 under Linux Mint 21.3 Cinnamon 6.0.4 - full sysinfo at end if needed. Sent a large color image which was received. As it finished, fldigi closed with the image window. After

Do you have Config Settings> Misc > Save Parameters> AFC Control checked or not? I did notice at one point that it prevented changing the setting if that was not checked in some modes.

Hi Greg, I'm also on Ubuntu 24.04 and use the WIKI build instructions. I have noticed the confusion on some of the steps. My Fldigi sometimes locks up and Top reports the Fldigi CPU utilization is

Hi Greg, I just did a fresh install of Ubuntu 24.04 this morning. I'm not sure where the sources file was moved off to, but you can enable the 'Source code' repository via the Software & Updates

Hi Levente, great, it's good to see that more and more loggers are available on Linux! :) yes, Fldigi has a good xmlrpc interface. I've already implemented that for Tlf (and later HA5CQZ Zoli