¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
New file uploaded to kicad-users
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the kicad-users group. File : /Library/DCDC-ACDC-Converter_RevC_20Jul2012.zip Uploaded by
By kicad-users@... · #12446 ·
New file uploaded to kicad-users
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the kicad-users group. File : /Library/Symbols_DCDC-ACDC-Converter_RevC_20Jul2012.lib
By kicad-users@... · #12445 ·
Re: Mounting holes missing solder mask opening
I'm not sure if some information might have been lost in translation. The only issue I can think of is this: Usually the boards are drilled before solder mask is applied. So if there are no openings
By robert · #12444 ·
Re: Mounting holes missing solder mask opening
Here's the latest I heard from the pcb house: "Since you have indicated that four holes are screw holes ,then the solder mask opening is necessity .because if no solder mask opening ,the hole wall
By prenato_2000 · #12442 ·
Re: Mounting holes missing solder mask opening
Hi Esteban, Robert, Sorry for the image issue. Here it is what I intended to post. Hopefully will show now: [layoutIssue] http://xa.yimg.com/kq/groups/16027698/sn/1220508062/name/layoutIssue.jpg I
By prenato_2000 · #12441 ·
Re: Mounting holes missing solder mask opening
I forgot to tell you that I can't see the image (when I click your message on Yahoo's page a dialog asking user name and password appears).
By e_e_lucchesi · #12440 ·
Re: Mounting holes missing solder mask opening
--- In kicad-users@..., "prenato_2000" <prenato_2000@...> wrote: > > Hi Robert, > Thanks a lot for your feedback. Here's an image. The layer in blue are > the drill holes where the four
By e_e_lucchesi · #12439 ·
Re: Mounting holes missing solder mask opening
I haven't had problems with "1pin" before. Did you check the gerber files with a gerber viewer? (gerbv is quite good). Can you post them, or at least the 'picture'?
By robert · #12438 ·
Re: Multi sheet
Never had problems folding the big drawings up from new, but like large maps, getting them folded after you open them is always a pain especially if someone else folded them first. :-) It was a very
By Andy Eskelson <andyyahoo@...> · #12436 ·
Mounting holes missing solder mask opening
Hi I'm new to pcb making and tried nding my first Kicad design to iteadstudios. They are reporting an issue with the mounting holes in my Gerbers: "there are 4 drill size 3.0 mm that are missing
By prenato_2000 · #12437 ·
Re: Paste stencil "window pane" GND pad issue
Berwyn: I was hoping somebody would chime in with an answer to your question. Alas, it is not me. The only information I have found for KiCAD support of large thermal pads is in the Files folder of
By Wayne C. Gramlich · #12435 ·
Re: Multi sheet
Hi Yes ;) Big schematics in big sheets of paper with an A0 plotter available and a big table around. Then some serious amount of careful folding to make it fit the remaining documentation, in a way
By JorgeF_Tech <jorgef.tech@...> · #12434 ·
Re: Multi sheet
It seems to me that if you have a multi-sheet schematic, you need some way to show how those sheets are interconnected, both for KiCad and for the user. The most obvious way to show the connections
By Peter Bennett <peterbb@...> · #12433 ·
Re: Multi sheet
There are developer forums and the software repository, however the developers do read the posts here so I expect that your comments have already been picked up. Andy "sebastien.duvier"
By Andy Eskelson <andyyahoo@...> · #12432 ·
Re: internal autorouter
i was using autorouter to finalize board by completing the 'no brainer' traces. one of the problem was that it only used default trace with, not the one defined by netclass.? once i mentioned that on
By ike · #12431 ·
Re: Hi kicad outputs parts lists are their ways to connect that to a mouser and digi
google searching digikey databas lead me to some interesting results. octopart api was one of them so maby that and a linux mysql database and php might work.
By josh_eeg · #12430 ·
Re: Multi sheet
Hello Andy, Thanks a lot for your reply. Do you know if it could be considered for the next version of Kicad ? I saw that I'm not alone to expect this feature... where can I submit (if it's not
By sebastien.duvier · #12429 ·
Re: internal autorouter
it seemed to work ok with a simple board, but i tried it on one of the demo boards which was low-medium complexity (carte_test.brd) and it crashed pcbnew... is there a log i can check to see what
By jed martin · #12428 ·
Re: internal autorouter
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 For the first crack at it, it will be one way. You'll have to generate your gerber files from geda pcb. This is intended to be just a work-around while
By Michael Sharkey · #12427 ·
Re: Hi kicad outputs parts lists are their ways to connect that to a mouser and digi
It is highly unlikely that you will find such a list. Major distributors will have a catalogue of 100's of thousands of parts. The first problem is that Mouser and Digikey ARE NOT component
By Andy Eskelson <andyyahoo@...> · #12426 ·