¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Re: Spots to control radio

 

That did it, thank you.

On Mon, Nov 18, 2024 at 11:22?AM Bob via <k4cy=[email protected]> wrote:
Look at the parallel logging configuration. There is an option there to reroute clicked-on DX Spots to the other PC. SeventyThree(s).
On 11/18/2024 12:03 PM EST Don Moman VE6JY via <ve6jy.1=[email protected]> wrote:
?
?
Several weeks ago, Logger32 lost the ability to send my radio to a dx spot frequency and to populate the entry window.? Rig control works fine and I can type a frequency in and the radio will go there.? But clicking on a DX spot doesn't do anything - the entry window flashes briefly but neither the frequency or the callsign show up.? This used to work fine and I haven't (knowingly) made any changes.? I have a second computer synced to provide backup logging - that computer will populate the entry window and the frequency shows for several seconds?(but this computer doesn't have rig control).? Looking through the manual and searching for this issue hasn't shown me anything to look at. Both computers are running the latest version and have updated several times.?
?
Any suggestions are appreciated, thanks.
?
Don
VE6JY


Re: Spots to control radio

 

Look at the parallel logging configuration. There is an option there to reroute clicked-on DX Spots to the other PC. SeventyThree(s).

On 11/18/2024 12:03 PM EST Don Moman VE6JY via groups.io <ve6jy.1@...> wrote:
?
?
Several weeks ago, Logger32 lost the ability to send my radio to a dx spot frequency and to populate the entry window.? Rig control works fine and I can type a frequency in and the radio will go there.? But clicking on a DX spot doesn't do anything - the entry window flashes briefly but neither the frequency or the callsign show up.? This used to work fine and I haven't (knowingly) made any changes.? I have a second computer synced to provide backup logging - that computer will populate the entry window and the frequency shows for several seconds?(but this computer doesn't have rig control).? Looking through the manual and searching for this issue hasn't shown me anything to look at. Both computers are running the latest version and have updated several times.?
?
Any suggestions are appreciated, thanks.
?
Don
VE6JY


Spots to control radio

 

Several weeks ago, Logger32 lost the ability to send my radio to a dx spot frequency and to populate the entry window.? Rig control works fine and I can type a frequency in and the radio will go there.? But clicking on a DX spot doesn't do anything - the entry window flashes briefly but neither the frequency or the callsign show up.? This used to work fine and I haven't (knowingly) made any changes.? I have a second computer synced to provide backup logging - that computer will populate the entry window and the frequency shows for several seconds?(but this computer doesn't have rig control).? Looking through the manual and searching for this issue hasn't shown me anything to look at. Both computers are running the latest version and have updated several times.?

Any suggestions are appreciated, thanks.

Don
VE6JY


Re: Issue on v4.0.329 with the Quick QSL window

 




Alain,

it IS painful.
As I cannot define the added value in that venture
I had to rollback to the previous version, too...

Best regards,
Alec



------ Wiadomo?? oryginalna ------
Nadawca "Bob via groups.io" <k4cy@...>
Do [email protected]; "Alain F5LMJ via groups.io" <f5lmj@...>
Data 17.11.2024 10:22:46
Temat Re: [hamlogger] Issue on v4.0.329 with the Quick QSL window

Yes, there were changes made that slow down the opening of the Quick QSL window, but no changes that slow down how long it takes to change whatever you wanted to change. And, the delay in opening the Quick QSL window is only the first time you open the window.
?
And why the delay? When opening the Quick QSL window you are jumping into the logbook database somewhere. Loggoer32 needs to find out exactly where you are and move the vertical scrollbar thumb (the slider on the scrollbar) to the correct position. Why do this? So that scrolling up/down works correctly.
?
To see the difference, on v4.0.328, Open the Quick QSL window on a QSO somewhere in the middle of your logbook. Now on the vertical scrollbar? click with the mouse to scroll up one row. Did it go up one row? I think not.
?
C'est la vie. SeventyThree(s).
?
On 11/17/2024 3:57 AM EST Alain F5LMJ via groups.io <f5lmj@...> wrote:
?
?
Since version v4.0.329 I have a problem with the Quick QSL window any update takes on this version very long time before applying and block any other action. On v4.0.328 the update is done instantly. So I need to rollback to 328
Does anyone have also this issue ?
Is there any change in Quick QSL window between 328 and 329 ?
?
73, Alain F5LMJ ?


Re: Issue on v4.0.329 with the Quick QSL window

 

Yes, there were changes made that slow down the opening of the Quick QSL window, but no changes that slow down how long it takes to change whatever you wanted to change. And, the delay in opening the Quick QSL window is only the first time you open the window.
?
And why the delay? When opening the Quick QSL window you are jumping into the logbook database somewhere. Loggoer32 needs to find out exactly where you are and move the vertical scrollbar thumb (the slider on the scrollbar) to the correct position. Why do this? So that scrolling up/down works correctly.
?
To see the difference, on v4.0.328, Open the Quick QSL window on a QSO somewhere in the middle of your logbook. Now on the vertical scrollbar? click with the mouse to scroll up one row. Did it go up one row? I think not.
?
C'est la vie. SeventyThree(s).
?

On 11/17/2024 3:57 AM EST Alain F5LMJ via groups.io <f5lmj@...> wrote:
?
?
Since version v4.0.329 I have a problem with the Quick QSL window any update takes on this version very long time before applying and block any other action. On v4.0.328 the update is done instantly. So I need to rollback to 328
Does anyone have also this issue ?
Is there any change in Quick QSL window between 328 and 329 ?
?
73, Alain F5LMJ ?


Issue on v4.0.329 with the Quick QSL window

 

Since version v4.0.329 I have a problem with the Quick QSL window any update takes on this version very long time before applying and block any other action. On v4.0.328 the update is done instantly. So I need to rollback to 328
Does anyone have also this issue ?
Is there any change in Quick QSL window between 328 and 329 ?
?
73, Alain F5LMJ ?


Re: Rollback

 

Only the last 10 are kept. Anything older is automatically deleted. SeventyThree(s).

On 11/16/2024 12:44 PM EST Jean-Claude ROUGE via groups.io <j-cl.rouge@...> wrote:
?
?

Hello,

On my rollback window, I have 4.0.318 to 4.0.328 possibility.

Is possible to go back to an earlier versionn (before 4.0.318), and if yes, how ?

Tks for your help and your answer.

73's.

Jean-Claude? F6HDH


Rollback

 

¿ªÔÆÌåÓý

Hello,

On my rollback window, I have 4.0.318 to 4.0.328 possibility.

Is possible to go back to an earlier versionn (before 4.0.318), and if yes, how ?

Tks for your help and your answer.

73's.

Jean-Claude? F6HDH


Something odd with Radio connection?

 

So,? just recently starting seeing L32 with an odd radio connection problem...
?
Radio is FTdx101D connected to L32 via a Microham Station Master box at 19200, N, 8, 1 and polling is set at 50mS, but slower poling makes no difference.
?
When I first start L32 from cold, I see that both the Radio 1 and Rotator 1 are connected fine, as indicated by the blue status on the taskbar, and also confirmed by the frequency showing correctly in the entry window.?
?
I wait until the cluster spots have populated the band monitor panels, then I click on a spot on the monitor panel. At that exact moment the "Radio 1" on the taskbar changes from Blue (connected) to Red (not connected).? I then have to manually make L32 re-connect to the radio via the setup > Radio menu.
?
All is then fine and dandy and I don't see the problem again during that run-time session. However, the same repeats every time I start L32. Some kind of timing/hand-shake issue maybe?
?
?Any clues on this issue please?
?
Steve G1XOW
?


Re: CW Machine Keyer setup

 
Edited

the software win4yaesu may do that winkey function
from Tom aka va2fsq . . .
?


Re: CW Machine and FTdx10

 

My configuration, and it works perfectly?:-)
CW machine
?->>?CONFIG?
->> flag SOFTWARE?
Keyer setup (wait a moment)?
SERIAL PORT choose the port com# STANDARD (not Enhanced) Flaggare?
-->> flag Use PTT to switch to transmit?
-->> flag CW Keying users RTS PTT, users DTR Flaggare?
->> flag Use dedicated serial port fo CW?
->> flag Use Radio command PTT override

Best 73' de Gianni IK6CGO



------ Messaggio originale ------
Da "ja1nlx via groups.io" <ayoshida0205@...>
A "Hanlogger" <[email protected]>
Data 14/11/2024 07:36:24
Oggetto Re: [hamlogger] CW Machine and FTdx10

Clark
I do not know why PC keying does not work.
However WinKeyer is better than software mode. I myself prefer WinKeyer.
Mine is WinKeyMini by K1EL.
Good luck

73 de aki
JA1NLX

On 2024-11-14 ľê×ÈÕ 15:23:07, Clark Stewart via groups.io <w8tn@...> wrote:

Hello Aki,
?
I am sure I tried that and it did not work either.? So, I have given up trying to get CW Machine to send CW from my FTdx10 via software.? A local friend had a WinKeyer he was not using and let me borrow it.? After some work I managed to get it working just fine with CW Machine.
?
Thanks to you and Gary for trying to help me with this.? But by adding the WinKeyer, I can now use CW Machine with the FTdx10 just like I used to with my microKEYER and K3S.?
?
?
73, Clark, W8TN
?


Re: CW Machine and FTdx10

 

Clark
I do not know why PC keying does not work.
However WinKeyer is better than software mode. I myself prefer WinKeyer.
Mine is WinKeyMini by K1EL.
Good luck

73 de aki
JA1NLX

On 2024-11-14 ľê×ÈÕ 15:23:07, Clark Stewart via groups.io <w8tn@...> wrote:

Hello Aki,
?
I am sure I tried that and it did not work either.? So, I have given up trying to get CW Machine to send CW from my FTdx10 via software.? A local friend had a WinKeyer he was not using and let me borrow it.? After some work I managed to get it working just fine with CW Machine.
?
Thanks to you and Gary for trying to help me with this.? But by adding the WinKeyer, I can now use CW Machine with the FTdx10 just like I used to with my microKEYER and K3S.?
?
?
73, Clark, W8TN
?


Re: CW Machine and FTdx10

 

Hello Aki,
?
I am sure I tried that and it did not work either.? So, I have given up trying to get CW Machine to send CW from my FTdx10 via software.? A local friend had a WinKeyer he was not using and let me borrow it.? After some work I managed to get it working just fine with CW Machine.
?
Thanks to you and Gary for trying to help me with this.? But by adding the WinKeyer, I can now use CW Machine with the FTdx10 just like I used to with my microKEYER and K3S.?
?
?
73, Clark, W8TN
?


Re: CW Machine and FTdx10

 

Clark
Try RTS keying instead of DTR keying.
(Select RTS keying in your radio, check "CW keying use RTS,,," in CW machine)

73 de aki
JA1NLX

On 2024-11-13 Ë®ê×ÈÕ 22:18:07, Clark Stewart via groups.io <w8tn@...> wrote:

First, thanks guys for the speedy responses!
?
Gary, thanks for the detailed info.? I had seen that info during my searches but was hoping to be able to do it without the hardware interface.? The FTdx10 manual (on Page 56) says:
?
By connecting the FTDX10 to a computer,?
CW can be operated using free or commer-
cially available software and setting Menu?
item "PC KEYING" (PAGE 96).
And, under "PC KEYING" (page 96 of the manual) says for both RTS and DTR:
?
Controls the transmit from the USB virtual COM/RTS (COM/DTR) ports.
?
I was assuming from the above that "PC KEYING" did not require a hardware interface.
?
==========
?
Aki, your info is what I was looking for but it does not seem to work for me.?
?
My installation has Enhanced (COM17) and Standard (COM 23).
?
Here is the "Setup" for my CW Machine:
?
?
On the radio - CW Setting | Mode CW?? --? I have the following set:
CW BK-IN TYPE (tried both Full and Semi)
PC Keying - DTR
All other settings are the default ones.
?
I forget now why I installed VSPE (Virtual Serial Port Emulator) and set up a ¡°Splitter¡± for the FTdx10 Enhanced serial port (COM 17) and created a New COM port ¨C COM 34 but I did.? Anyway, that is on the Enhanced port.
?
When I click on a message in CW Machine, the FTdx10 goes into Transmit but there is no CW heard in the monitor (MONI Level is set to 100) and there is no power out. (RF POWER is set to 70 watts.)? The KPA1500 amp switches into TX but no power out.? The radio stays keyed for the duration of the message.
?
If I set KEYER to ON or to OFF, no change.? If I set BK-IN to ON or OFF, no change.
?
If I use the internal MESSAGE function of the FTdx10, I hear the CW sidetone and there is power out.? I just can not get CW Machine to do more than key the PTT.
?
There must be something I have overlooked or set incorrectly.? That's why I was asking for help from anyone using CW Machine to send CW with the FTdx10.? Maybe someone will read this who has it working and can tell me what I have done wrong or not done.
?
Thanks again.? 73, Clark, W8TN
?
?
?
?


Re: CW Machine Keyer setup

 

Thanks for the tip. Will give it a go tomorrow.



On Wed, Nov 13, 2024 at 16:22, Bob via groups.io <k4cy@...> wrote:
Assuming your Logger32 installations were doing a full install, and not simply copying files/folders from one computer to another. My SWAG is that the dysfunctional PC has a Windows component, that Logger32 uses, missing.
?
If you don't already have one, setup a desktop shortcut that starts Logger32. Now read section 34.4 (page 758) of the help file. You will then be able to start Logger32 in full debug mode and hopefully identify the exact source of your problem.
?
SeventyThree(s).
On 11/13/2024 10:54 AM EST Albert Crespo via groups.io <f5vhj@...> wrote:
?
?
I have been using Logger 32 for many years.
I did a? fresh installed on a new computer.
The CW machine under config, I click keyer setup and get the dreaded hour glass, and then nothing happens.
Everything else works fine. Radio read out is correct, etc.
So, went to another new computer and installed Logger 32. I do the same thing and the keyer menu appears and I can configure the the program to work on the software and WinKey.
However , on this computer it does not read the frequency of the radio. The debug window indicates it is on the correct com port.
I have a? sense? this is a Windows 11 issue.
?
?


Re: CW Machine and FTdx10

 

Hmmmmm, OK.

Your PTT is working fine using the CAT commands, so it seems it's just the CW keying using the DTR line on 'standard' virtual serial port Com23 that's playing up.

I don't know why - sorry - something to do with the setup of the virtual?port I guess, but how to diagnose & fix that is beyond me (at 5:30am anyway!).

All I can suggest is to work carefully through the Yaesu instructions for the ?to be sure you have the current driver correctly installed.? That may involve de-installing the driver first, then re-installing it.? Or something.

If you want to prove that the CW Machine is keying the DTR line as it should, I guess you'd need some software to monitor the virtual port line, or maybe you could temporarily change to a real serial port and put a scope or DMM on the DTR line of that port, looking for the level changes when CW is being sent (easier to see with? ? v e r y? ? ?s l o w? ? ?C W).??

73? GL
Gary?
?beater/tester &?
Honor Roll &? checker



On Thu, 14 Nov 2024 at 02:18, Clark Stewart via <w8tn=[email protected]> wrote:
First, thanks guys for the speedy responses!
?
Gary, thanks for the detailed info.? I had seen that info during my searches but was hoping to be able to do it without the hardware interface.? The FTdx10 manual (on Page 56) says:
?
By connecting the FTDX10 to a computer,?
CW can be operated using free or commer-
cially available software and setting Menu?
item "PC KEYING" (PAGE 96).
And, under "PC KEYING" (page 96 of the manual) says for both RTS and DTR:
?
Controls the transmit from the USB virtual COM/RTS (COM/DTR) ports.
?
I was assuming from the above that "PC KEYING" did not require a hardware interface.
?
==========
?
Aki, your info is what I was looking for but it does not seem to work for me.?
?
My installation has Enhanced (COM17) and Standard (COM 23).
?
Here is the "Setup" for my CW Machine:
?
?
On the radio - CW Setting | Mode CW?? --? I have the following set:
CW BK-IN TYPE (tried both Full and Semi)
PC Keying - DTR
All other settings are the default ones.
?
I forget now why I installed VSPE (Virtual Serial Port Emulator) and set up a ¡°Splitter¡± for the FTdx10 Enhanced serial port (COM 17) and created a New COM port ¨C COM 34 but I did.? Anyway, that is on the Enhanced port.
?
When I click on a message in CW Machine, the FTdx10 goes into Transmit but there is no CW heard in the monitor (MONI Level is set to 100) and there is no power out. (RF POWER is set to 70 watts.)? The KPA1500 amp switches into TX but no power out.? The radio stays keyed for the duration of the message.
?
If I set KEYER to ON or to OFF, no change.? If I set BK-IN to ON or OFF, no change.
?
If I use the internal MESSAGE function of the FTdx10, I hear the CW sidetone and there is power out.? I just can not get CW Machine to do more than key the PTT.
?
There must be something I have overlooked or set incorrectly.? That's why I was asking for help from anyone using CW Machine to send CW with the FTdx10.? Maybe someone will read this who has it working and can tell me what I have done wrong or not done.
?
Thanks again.? 73, Clark, W8TN
?
?
?
?


Re: CW Machine Keyer setup

 

Assuming your Logger32 installations were doing a full install, and not simply copying files/folders from one computer to another. My SWAG is that the dysfunctional PC has a Windows component, that Logger32 uses, missing.
?
If you don't already have one, setup a desktop shortcut that starts Logger32. Now read section 34.4 (page 758) of the help file. You will then be able to start Logger32 in full debug mode and hopefully identify the exact source of your problem.
?
SeventyThree(s).

On 11/13/2024 10:54 AM EST Albert Crespo via groups.io <f5vhj@...> wrote:
?
?
I have been using Logger 32 for many years.
I did a? fresh installed on a new computer.
The CW machine under config, I click keyer setup and get the dreaded hour glass, and then nothing happens.
Everything else works fine. Radio read out is correct, etc.
So, went to another new computer and installed Logger 32. I do the same thing and the keyer menu appears and I can configure the the program to work on the software and WinKey.
However , on this computer it does not read the frequency of the radio. The debug window indicates it is on the correct com port.
I have a? sense? this is a Windows 11 issue.
?
?


CW Machine Keyer setup

 

I have been using Logger 32 for many years.
I did a? fresh installed on a new computer.
The CW machine under config, I click keyer setup and get the dreaded hour glass, and then nothing happens.
Everything else works fine. Radio read out is correct, etc.
So, went to another new computer and installed Logger 32. I do the same thing and the keyer menu appears and I can configure the the program to work on the software and WinKey.
However , on this computer it does not read the frequency of the radio. The debug window indicates it is on the correct com port.
I have a? sense? this is a Windows 11 issue.


Re: CW Machine and FTdx10

 

First, thanks guys for the speedy responses!
?
Gary, thanks for the detailed info.? I had seen that info during my searches but was hoping to be able to do it without the hardware interface.? The FTdx10 manual (on Page 56) says:
?
By connecting the FTDX10 to a computer,?
CW can be operated using free or commer-
cially available software and setting Menu?
item "PC KEYING" (PAGE 96).
And, under "PC KEYING" (page 96 of the manual) says for both RTS and DTR:
?
Controls the transmit from the USB virtual COM/RTS (COM/DTR) ports.
?
I was assuming from the above that "PC KEYING" did not require a hardware interface.
?
==========
?
Aki, your info is what I was looking for but it does not seem to work for me.?
?
My installation has Enhanced (COM17) and Standard (COM 23).
?
Here is the "Setup" for my CW Machine:
?
?
On the radio - CW Setting | Mode CW?? --? I have the following set:
CW BK-IN TYPE (tried both Full and Semi)
PC Keying - DTR
All other settings are the default ones.
?
I forget now why I installed VSPE (Virtual Serial Port Emulator) and set up a ¡°Splitter¡± for the FTdx10 Enhanced serial port (COM 17) and created a New COM port ¨C COM 34 but I did.? Anyway, that is on the Enhanced port.
?
When I click on a message in CW Machine, the FTdx10 goes into Transmit but there is no CW heard in the monitor (MONI Level is set to 100) and there is no power out. (RF POWER is set to 70 watts.)? The KPA1500 amp switches into TX but no power out.? The radio stays keyed for the duration of the message.
?
If I set KEYER to ON or to OFF, no change.? If I set BK-IN to ON or OFF, no change.
?
If I use the internal MESSAGE function of the FTdx10, I hear the CW sidetone and there is power out.? I just can not get CW Machine to do more than key the PTT.
?
There must be something I have overlooked or set incorrectly.? That's why I was asking for help from anyone using CW Machine to send CW with the FTdx10.? Maybe someone will read this who has it working and can tell me what I have done wrong or not done.
?
Thanks again.? 73, Clark, W8TN
?
?
?
?


Re: CW Machine and FTdx10

 

There are 2 ways to send CW.
One is explained by Gary.
Anther is to use RTS or DTR line in created virtual com port.
You should set CW keying option in your radio. (DTR or RTS)
You should set proper com port setting in CW machine. This is example.

When USB cable is connected to PC then you have new two COM port, Enhanced and Standard.
In my case, I see COM9 (enhanced) and COM10 (Standard) I use COM9 for CAT and COM10 for CW keying on?DTR line.



73 de aki
JA1NLX

On 2024-11-13 Ë®ê×ÈÕ 13:01:20, Clark Stewart via groups.io <w8tn@...> wrote:

I have searched the Hamlogger messages, the Logger32 manual, the FTdx10 manual, the FTdx10 Google Group, multiple Google searches, watched several YouTube videos . . . and I'm stumped.? I'm trying to get CW Machine to work (via Software) with my FTdx10.? I can get CW Machine to key the PTT on the FTdx10 but can not get it to send CW.? I can send "canned" messages from the FTdx10 so the CW does work on the radio.
?
Has someone already done this and has CW Machine sending CW (by software) to the FTDX10?? Can you tell me the Magic Trick to get this to work?? Remember, I'm trying to do this by software and not by using a WinKeyer or similar hardware device.? Thanks.
?
73, Clark, W8TN
?