Hi bill?
I assume you've set the COM port correctly in Windows and similarly in Logger32? I think the port speed should be 4800 or lower. I'd also try increasing the pooling value in L32 in the workstation's configuration window. 73 chris?
toggle quoted message
Show quoted text
Le 6 avr. 2025 à 22:24, Bob via groups.io <k4cy@...> a écrit?:
?
I don't have a Kenwood radio, but I configured for a TS-2000 (as instruvted n section 49.5 of the help file.?I see this in rhe radio debug window.
?
As expected, no radio, so no poll replies. I see no reference to ?VFO-B. SeventyThree(s).
?
n 04/06/2025 3:56 PM EDT Bill Neumann <billn@...> wrote:
?
?
This might be a shot in the dark, but I cannot seem to get Logger32 to talk to my Kenwood TS870.
I have tried everything I can see in the manual, but still not getting any where.
I admit, I am a total newbie but do have a decent understanding of computer ports and connections.
When I look at the debug window, I see it polling the B VFO and not the A.
Any insight would be a greatly appreciated.
?
73
Bill
KB0RMS
?
|
Re: Potential enhancement request - configurable Echo Port
Look at section 49.6.4 to see if you can't figure out a way to free up the Logger32 slave port panadaptor by using omni-rig. SeventyThree(s).
On 04/06/2025 4:51 PM EDT John, G4DRS via groups.io <g4drs@...> wrote:
?
?
Thanks for the prompt attention and the useful suggestions, Bob.
I already use the Slave port to link to an SDR for a panadapter - you can't have too many screens...:)
As far as I can see, the echo port only sends out what the radio sends out, I can't see a way to configure it as a different radio type. Or am I missing something?
I hope so...
?
73,
?
John
G4DRS?
|
Re: Potential enhancement request - configurable Echo Port
Thanks for the prompt attention and the useful suggestions, Bob.
I already use the Slave port to link to an SDR for a panadapter - you can't have too many screens...:)
As far as I can see, the echo port only sends out what the radio sends out, I can't see a way to configure it as a different radio type. Or am I missing something?
I hope so...
?
73,
?
John
G4DRS?
|
I don't have a Kenwood radio, but I configured for a TS-2000 (as instruvted n section 49.5 of the help file.?I see this in rhe radio debug window.
?
As expected, no radio, so no poll replies. I see no reference to ?VFO-B. SeventyThree(s).
?
n 04/06/2025 3:56 PM EDT Bill Neumann <billn@...> wrote:
?
?
This might be a shot in the dark, but I cannot seem to get Logger32 to talk to my Kenwood TS870.
I have tried everything I can see in the manual, but still not getting any where.
I admit, I am a total newbie but do have a decent understanding of computer ports and connections.
When I look at the debug window, I see it polling the B VFO and not the A.
Any insight would be a greatly appreciated.
?
73
Bill
KB0RMS
?
|
This might be a shot in the dark, but I cannot seem to get Logger32 to talk to my Kenwood TS870.
I have tried everything I can see in the manual, but still not getting any where.
I admit, I am a total newbie but do have a decent understanding of computer ports and connections.
When I look at the debug window, I see it polling the B VFO and not the A.
Any insight would be a greatly appreciated.
?
73
Bill
KB0RMS
?
|
Re: Potential enhancement request - configurable Echo Port
... there are even a handful on slave radio specific macros on the Radio Control Panel that may be of interest. SeventyThree(s).
On 04/06/2025 9:21 AM EDT Bob <k4cy@...> wrote:
?
?
... Section 12.6, and 12.7 might also be enlightening. SeventyThree(s).
On 04/06/2025 9:14 AM EDT Bob <k4cy@...> wrote:
?
?
Isn't that done automagically? Example, configure the primary as (say) a Yaesu whatever.? Configure the Echo port as (say) an Icom whatever. Spin the dial on the primary radio, Yaesu formatted messages are received by Logger32, decoded, and sent to the echo radio in Icom format.
?
Some commands simply don't translate from one radio brand to another.? So, configure a slave port instead, and map the differences - Like CW on the primary radio CW-R on the slave.
?
Or, look at section 2.5 (page 275) of the help file.
?
SeventyThree(a).
?
On 04/06/2025 8:38 AM EDT John, G4DRS via groups.io <g4drs@...> wrote:
?
?
I wonder, is it possible to have Logger32 translate the CAT data received from a connected radio before it sends it to the Echo port?
I have searched the user manual, but can't see anything. That's not to say it isn't there, of course...
?
The use case I have in mind is:
Radio (FTdx101) connected to Logger32 via USB
Amplifier (Acom 2000) connected to radio via coax and PTT cable
?
At present, the amplifier automatically tunes to whatever segment it detects when I send it some RF.
It is possible, however, to connect the amplifier to a serial port and have it select the appropriate band segment as the data on the serial port changes. This means the amplifier is already tuned correctly prior to RF being applied, which is probably slightly better for the amplifier.
?
In a perfect world, I could connect the amplifier CAT port to the serial connector on the rear panel of the radio, but, apparently, the Acom doesn't speak FTdx101 language. Yaesu changed the format of the CAT data for the FTdx101 & FTdx10 series of radios, as I understand it.
Thus, I thought a work-around could be to send the data out from the logging software via the Echo port. It would need to be translated into something more vanilla, before being sent, though- Kenwood TS2000 or Yaesu FT1000, maybe. This would compensate for the amplifier firmware's inability to communicate with the FTdx101 or FTdx10.
?
Is there already a way to do this?
If not, is it something that would constitute a worthwhile enhancement?
Or is it only me?
?
?
Cheers,
?
John
G4DRS
|
Re: Potential enhancement request - configurable Echo Port
... Section 12.6, and 12.7 might also be enlightening. SeventyThree(s).
On 04/06/2025 9:14 AM EDT Bob <k4cy@...> wrote:
?
?
Isn't that done automagically? Example, configure the primary as (say) a Yaesu whatever.? Configure the Echo port as (say) an Icom whatever. Spin the dial on the primary radio, Yaesu formatted messages are received by Logger32, decoded, and sent to the echo radio in Icom format.
?
Some commands simply don't translate from one radio brand to another.? So, configure a slave port instead, and map the differences - Like CW on the primary radio CW-R on the slave.
?
Or, look at section 2.5 (page 275) of the help file.
?
SeventyThree(a).
?
On 04/06/2025 8:38 AM EDT John, G4DRS via groups.io <g4drs@...> wrote:
?
?
I wonder, is it possible to have Logger32 translate the CAT data received from a connected radio before it sends it to the Echo port?
I have searched the user manual, but can't see anything. That's not to say it isn't there, of course...
?
The use case I have in mind is:
Radio (FTdx101) connected to Logger32 via USB
Amplifier (Acom 2000) connected to radio via coax and PTT cable
?
At present, the amplifier automatically tunes to whatever segment it detects when I send it some RF.
It is possible, however, to connect the amplifier to a serial port and have it select the appropriate band segment as the data on the serial port changes. This means the amplifier is already tuned correctly prior to RF being applied, which is probably slightly better for the amplifier.
?
In a perfect world, I could connect the amplifier CAT port to the serial connector on the rear panel of the radio, but, apparently, the Acom doesn't speak FTdx101 language. Yaesu changed the format of the CAT data for the FTdx101 & FTdx10 series of radios, as I understand it.
Thus, I thought a work-around could be to send the data out from the logging software via the Echo port. It would need to be translated into something more vanilla, before being sent, though- Kenwood TS2000 or Yaesu FT1000, maybe. This would compensate for the amplifier firmware's inability to communicate with the FTdx101 or FTdx10.
?
Is there already a way to do this?
If not, is it something that would constitute a worthwhile enhancement?
Or is it only me?
?
?
Cheers,
?
John
G4DRS
|
Re: Potential enhancement request - configurable Echo Port
Isn't that done automagically? Example, configure the primary as (say) a Yaesu whatever.? Configure the Echo port as (say) an Icom whatever. Spin the dial on the primary radio, Yaesu formatted messages are received by Logger32, decoded, and sent to the echo radio in Icom format.
?
Some commands simply don't translate from one radio brand to another.? So, configure a slave port instead, and map the differences - Like CW on the primary radio CW-R on the slave.
?
Or, look at section 2.5 (page 275) of the help file.
?
SeventyThree(a).
?
On 04/06/2025 8:38 AM EDT John, G4DRS via groups.io <g4drs@...> wrote:
?
?
I wonder, is it possible to have Logger32 translate the CAT data received from a connected radio before it sends it to the Echo port?
I have searched the user manual, but can't see anything. That's not to say it isn't there, of course...
?
The use case I have in mind is:
Radio (FTdx101) connected to Logger32 via USB
Amplifier (Acom 2000) connected to radio via coax and PTT cable
?
At present, the amplifier automatically tunes to whatever segment it detects when I send it some RF.
It is possible, however, to connect the amplifier to a serial port and have it select the appropriate band segment as the data on the serial port changes. This means the amplifier is already tuned correctly prior to RF being applied, which is probably slightly better for the amplifier.
?
In a perfect world, I could connect the amplifier CAT port to the serial connector on the rear panel of the radio, but, apparently, the Acom doesn't speak FTdx101 language. Yaesu changed the format of the CAT data for the FTdx101 & FTdx10 series of radios, as I understand it.
Thus, I thought a work-around could be to send the data out from the logging software via the Echo port. It would need to be translated into something more vanilla, before being sent, though- Kenwood TS2000 or Yaesu FT1000, maybe. This would compensate for the amplifier firmware's inability to communicate with the FTdx101 or FTdx10.
?
Is there already a way to do this?
If not, is it something that would constitute a worthwhile enhancement?
Or is it only me?
?
?
Cheers,
?
John
G4DRS
|
Potential enhancement request - configurable Echo Port
I wonder, is it possible to have Logger32 translate the CAT data received from a connected radio before it sends it to the Echo port?
I have searched the user manual, but can't see anything. That's not to say it isn't there, of course...
?
The use case I have in mind is:
Radio (FTdx101) connected to Logger32 via USB
Amplifier (Acom 2000) connected to radio via coax and PTT cable
?
At present, the amplifier automatically tunes to whatever segment it detects when I send it some RF.
It is possible, however, to connect the amplifier to a serial port and have it select the appropriate band segment as the data on the serial port changes. This means the amplifier is already tuned correctly prior to RF being applied, which is probably slightly better for the amplifier.
?
In a perfect world, I could connect the amplifier CAT port to the serial connector on the rear panel of the radio, but, apparently, the Acom doesn't speak FTdx101 language. Yaesu changed the format of the CAT data for the FTdx101 & FTdx10 series of radios, as I understand it.
Thus, I thought a work-around could be to send the data out from the logging software via the Echo port. It would need to be translated into something more vanilla, before being sent, though- Kenwood TS2000 or Yaesu FT1000, maybe. This would compensate for the amplifier firmware's inability to communicate with the FTdx101 or FTdx10.
?
Is there already a way to do this?
If not, is it something that would constitute a worthwhile enhancement?
Or is it only me?
?
?
Cheers,
?
John
G4DRS
|
Re: No COM Port read and ADIFCountries... missing
Thank you.
After some wait, logger32 sees COM4. Good? new on all fronts. Tnx for the update.
Ignacy NO9E
|
Re: FTdx101 Split Macro troubles
On Sat, Apr 5, 2025 at 06:02 AM, Darren Collins (G0TSM) wrote:
I'm an FTDX5000 user and I am aware what the VS command does in my radio, but in the FTDX101 does VS also assign the VFO dial?
?
?
73 Darren G0TSM
?
?
?
Darren,
If there were a prize, you would have won it!
?
Thanks, I was looking but not seeing...
?
That works perfectly.
?
Just in case anyone is interested, I will post my macros in the files section.
?
?
73
?
John
G4DRS
?
|
Re: No COM Port read and ADIFCountries... missing
As you've no doubt figured out, it was probably not a good idea to fall 300+ software updates behind.? I have sent you a zip file by direct mail. It contains the missing two files. Just unzip them into the default Logger32 folder.
?
COM4 is an entirely different matter. Suddenly v3.5.454 couldn't see COM4. The latest version v4.0.336. can't see COM4. N1MM continues to see COM4. Stick with what works.
?
SeventyThree(s).
On 04/05/2025 8:39 AM EDT Ignacy Misztal via groups.io <no9e@...> wrote:
?
?
Logger32 3.5.454 worked a week ago. Today It wold not connect to Flex via COM4. N1MM connects.
?
I updated to 4.0. It asked my to recalculate statistics. While the program was doing it, an upgrade windows popped up and I foolishly agreed before the recalculation was complete. Now when starting, there is a message about ADIFCountriesWithSecondary_Subdivisions.txt missing, and the program stops.?
?
Any idea why the COM4 stopped working with logger 32 and still works with N1MM?
How to fix the message?
?
When 4.0 came up, it also did not read COM4.
?
Ignacy NO9E
?
.?
|
Re: No COM Port read and ADIFCountries... missing
I added ADIFCountriesWithSecondary_Subdivisions.txt? from the installation file and logger32 works.
Still it does not connect via COM4.
Ignacy NO9E
|
No COM Port read and ADIFCountries... missing
Logger32 3.5.454 worked a week ago. Today It wold not connect to Flex via COM4. N1MM connects.
?
I updated to 4.0. It asked my to recalculate statistics. While the program was doing it, an upgrade windows popped up and I foolishly agreed before the recalculation was complete. Now when starting, there is a message about ADIFCountriesWithSecondary_Subdivisions.txt missing, and the program stops.?
?
Any idea why the COM4 stopped working with logger 32 and still works with N1MM?
How to fix the message?
?
When 4.0 came up, it also did not read COM4.
?
Ignacy NO9E
?
.?
|
Re: FTdx101 Split Macro troubles
I'm an FTDX5000 user and I am aware what the VS command does in my radio, but in the FTDX101 does VS also assign the VFO dial?
73 Darren G0TSM
toggle quoted message
Show quoted text
Is there a CAT command for the FTdx101 to mimic the press of either the big light blue 'MAIN' button or the darker blue 'SUB' button?
I have implemented a Split macro in Logger32, but I am having trouble finding the way to change the function of the main dial from tuning the main VFO to tuning the Sub VFO.
Therefore, when I run my split macro, the radio gets all set with the appropriate settings, but I still have to press that 'SUB' button before I can tune around the pile-up.
I've come from the FTdx5000, which has a separate tuning dial for the Sub VFO.
How have others addressed this issue?
?
73
John
G4DRS
|
Time to locate to another country Bob. The "leadership" of yours has gone crazy! 73 Ken ZL4NR?
To get hack to the original thread. Did you notice Heard Island is on the reciprocal tariff list at the minimum,10%. Norfolk Island rated 29%.
?
According to the BBC, Exports to the US from Heard in 2022 were valued at US$1.3M. for unspecified machinery and electrical products. The US Department of Commerce has so far not responded?to requests for clarification.
?
I sent a message?to DOGE on X asking Elon Musk to Maak nie saak om te kyk hoeveel goud daar in Ft Knox is nie. Kom ons gaan na Heard Island en kyk na die geheime elektroniese fabriek.
?
Your tax dollars at work. SeventyThree(s).
_,_._,_
|
To get hack to the original thread. Did you notice Heard Island is on the reciprocal tariff list at the minimum,10%. Norfolk Island rated 29%.
?
According to the BBC, Exports to the US from Heard in 2022 were valued at US$1.3M. for unspecified machinery and electrical products. The US Department of Commerce has so far not responded?to requests for clarification.
?
I sent a message?to DOGE on X asking Elon Musk to Maak nie saak om te kyk hoeveel goud daar in Ft Knox is nie. Kom ons gaan na Heard Island en kyk na die geheime elektroniese fabriek.
?
Your tax dollars at work. SeventyThree(s).
|
FTdx101 Split Macro troubles
Is there a CAT command for the FTdx101 to mimic the press of either the big light blue 'MAIN' button or the darker blue 'SUB' button?
I have implemented a Split macro in Logger32, but I am having trouble finding the way to change the function of the main dial from tuning the main VFO to tuning the Sub VFO.
Therefore, when I run my split macro, the radio gets all set with the appropriate settings, but I still have to press that 'SUB' button before I can tune around the pile-up.
I've come from the FTdx5000, which has a separate tuning dial for the Sub VFO.
How have others addressed this issue?
?
73
John
G4DRS
|
Will there be carve outs for up, down or certain colors of quarks?
-- Dave WB2PJH
|
WARNING:?? Do not drink Grouse!
In Scotland its the stuff we discard or export!?? :-)
Tom
GM4FDM
On 04/04/2025 11:59, Paul Sturpe via
groups.io wrote:
toggle quoted message
Show quoted text
I’m happy to contribute to a worthy cause.?
The 'Famous
Grouse' fund.
?
4th call area QSL Bureau “P”
letter manager
Paul Sturpe, W3GQ
8860 Peninsula Dr
Terrell, NC ?28682
?
|
jean-Christophe
Darren Collins (G0TSM)