开云体育

Hi, This is the biggst RF power band switch what I have seen! http://www.cnham.net/bbs/viewthread.php?tid=16539 I have some swaitch. I'm plan to use it in my next project:(1-2)4CX1000A amplifier, but

model 86 switches barely enough for a 4-1000A model 88 switches work well in QRO if you parallel a couple sets of contacts. I built a custom one with 3 decks 2 used for the inductor taps. It has 4

Dick, That's a heck of a lot cheaper than here in the states. Esentially, the monthly charge here is renting the transformers, even though you pay the large fee to have them hung on the pole and

Hi Dick, That's not what I've been tolled by Eneco (power company) in Capelle aan den IJssel when I moved into my new house 2 years ago. I forgot the actual quote, but it was more like in the range of

All, I have a HP 412A VTVM coming in, and I'm wondering what others may know about these? Anything I should look for, etc.? These don't have the rectifier tube in the probe like the 410 models do, but

Euro 175.- to get concerted from single phase service to 3 phase service in the Lowlands. For that money you'll get: 3 fuses a new 3 phase digital power/kWh meter 3 x 35 amps @ 400 VAC ( 42 kW AC, gud

PA3DUV escribi: And nothing else working from the same line. :) Best regards Guillermo - LU8EYW.

I was having problems with my ISP, it seems it implemented a very agressive SPAM filter, so I was not receiving all posts since three weeks ago or so. Best regards Guillermo - LU8EYW.

Rich, I forget what they call that now, but they sure are! There's a minimum you pay whether you use it or not. Best, Will to over

Can anyone tell me how to select unmarked wafer switches for RF switching, such as e-shopping at Surplus Sales? What is the general rule regarding contact spacing vs HV? If unmarked, how do I get into

Denny, A rotary converter (pony motor) is the only way to do it correctly. A static converter is simply a started capacitor bank to get the motor up to speed then it drops out letting the motor run on

See Below, offering out other CB I've not had the chance to read that one. What was it about? the

Sometimes, a 3-0 service has a monthly minimum charge that will blow the hat clean off of one's head.

Being that my Bridgeport mill is 1.5 HP, I use a rotary convertor to change the 220X1 to 220X3... Not perfect but it works... I did consider asking Consumers Power Co. to give me a price for 3 phase

Yeah, that's what I am doing... We quickly metered the remaining four... They are good, but two had drifted out of the 5% range a small amount and two were still in range... Each one is dissipating

He is one of our "recognized amplifier experts". - Tom Rauch, W8JI, Nov. 1994 *QST* magazine And he has not yet taken a class in alternating-current circuit analysis.

Mike, The kicker is, this un-named moderator said "You have been given a wide degree of latitude - wider than many others". For what, offering technical advice to any who asked for it? They also said

A 3 phase service is mighty fine to have if one can afford to have it put in. I've not checked on the price in a while, but back in 1985, a 200 amp 220 volt service ran around $2000 from the power

Could well be. chortle. The laugher is that the "Administrator" / censor who jackboots folks out of AMPS for not giving a callsign, does not give a callsign himself. If Tom joins this discussion

Some of those with good technical knowledge are Tom's pals. My take on Tom is that he attracts people who share a common element in their childhoods. Apparently, the attraction is so strong that a