开云体育

FWIW, I finally decided to vote with my feet. It got so quiet over there that they had to start discussing the latest FCC band bland/phone expansion ad naseum. Too much crap for my blood. Mod-U-Lator,

Rich, If I recall, didn't Tom know about you and I being put on moderation before anyone else on there did? I remember the moderator placed you and I both on moderation the same night, and Tom was

These are some of the characteristics of dipsomania. Quite. During the grate parasitics debate, Joe was one of Tom's sycophants and attack dogs. According to rumour, Tom refers to this discu

Gents Posted a few new pix.... and edited the rest. Click on photo's... then VE7RF. 3 pages of em.... including the in rack pep/board.... and the shack rvs power trip board. Later...........Jim VE7RF

On a similar note After reading through some of the lytic maker's various engineering notes..... some notes will say NOT to run the unloaded V across a HV electrolytic at more than 75% of it's rating

wrote: make it part of the bleeder string with a variable resistor across the meter. I have 3 large resistors and 3 output caps. 100 uF at 3 KV. Old habits die hard though. I liked the meter in the RF

wrote: and ### what tubes is this for ??? I went through this b4... and tested various ga wires for my home made chokes, since none of the commercial made units would meet my needs. Your typ B+W 800

later....Jim VE7RF

ORIGINAL MESSAGE: wrote: ------------ REPLY FOLLOWS ------------ You're only seeing part of the equation. Note the three dots are the START of the sig, followed by a single space, and also note the

Why mess with 10 smaller resistors when Ohmite makes larger MOF 10M and 100M units?

I visited the ARRL website and downloaded the latest schematics and parts list and there are still errors. RFC 101 90 uH , 3A Plate Choke Pete Dahl p/n CKRF000100 The PWD part number references a 800

I have considered moving my volt meter to the power supply and make it part of the bleeder string with a variable resistor across the meter. I have 3 large resistors and 3 output caps. 100 uF at 3 KV.

060920@...> wrote: so end across. ### slick... but with 10 x 1 meg resistors + 10 kv... current is just 1 ma. To get 5 ma... with say 20 x resistors, only 2 meg in total is needed ! [100 K each.... x

Jim, pentalab wrote: And I have people wonder why I use so many resistors in my HV multiplier string. It's a pain but to get the voltage AND power rating, it is a necessary evil.

wrote: only rated for 250 to 500 volts. The newer film resistors are lower that the old carbon comp. but more stable. wa1gfz guilty. ### Tnx.... It appears their "FP" series resistor's will do the

Go to Dale vishay site and get voltage ratings. Many resistors are only rated for 250 to 500 volts. The newer film resistors are lower that the old carbon comp. but more stable. wa1gfz P.S. I have 6-

Gents. One of our 0-10 kv HV meters went Kablamo the other day. Consisted of a 0-1 ma meter movement... and 10 x 1 meg 2 watt MF resistors. Unloaded V was 7900 v at the time. We have two identical HV

wrote: wrote: meter base of the antenna. The length of feeder that is not at 1:1 VSWR is trivially short. with discs]. Hydrator] was humidity...

In addition the use of a decimal and space repeated 3 times is a mathematical notation signifying the missing, but obvious, elements, so the mathematical series n^2{1 10} = 1 4 9 . . . 100 allows one

Indeed, Paul R L Measures, AG6K, 805.386.3734 r@..., , rlm@..., www.somis.org