开云体育

Metering, Power Supply, control circuitry, everything from the utility input to the HV of your choice. 230vac Single phase HV transformer rated at 1 amp continuous at 3000/3500/4000/4500 secondary

No but I have the WD7S version, complete with all parts and instructions. No idea what it is worth. See https://silo.tips/download/the-wd7s-triode-control-board Also, for a picture of a completed

THANKS Jim, GM3SEK web pages are good! ANYONE have one of GM3SEK triode control boards/kit for sale? 73 Robert W5AJ

In Europe Capton or Mica were used as insulation material on broadcast amplifier tubes and capacitors by companies like Plisch, R&S, Siemens, SEL etc.. I used Teflon with my YL1056 to insulate the

Yes, it is a 2m amp with YC-179. The quarter wave stub is a notchfilter for harmonic supression. The amplifier is built and used by a friend. 73 Peter -----Original-Nachricht----- Betreff: Re:

On Sat, Jan 6, 2024 at 09:44 PM, Steve wrote: > > > > I could tell I was beating a dead horse when all the HFers ignored my > earlier comments about plate bypass capacitors made of two metal plates >

Don't mess with the PIEL software.? The gold standard is the GM3SEK? PI / PI-L spreadsheet.? ?It's better since it factors in everything, like stray C....and also the all important stray L? Any

##? I don't get it.? You already depict a PI network, with adjustable pair of caps and small coil.? ?How exactly does the heliax fit into the overall scheme ?? ?Is this? 144 mhz amp with the

*12 KW CCS ON 160-15M...USING THE 3CX-6000A7... PART 10* *Here the Teflon SFT-600 coax (teflon version of LMR-600UF) is installed between the 3000 pf vac load cap and the paralleled Jennings RJ2B

How do I calibrate the power meter in the ALS-600? I guess thru a hole in the label below the RF Out connector on the back. Joe? N9VX

Everything is in bound. I found the relays and made an offer on the trimmers and the seller accepted. Going to have 125 bucks or so into this. Will probably need some mica caps also. I have some, Fred

I could tell I was beating a dead horse when all the HFers ignored my earlier comments about plate bypass capacitors made of two metal plates with an insulating sheet between, and then when they kept

Steve, K0XP said "Try a 3/4 wavelength stripline. Get the design info from W6GGV's articles published in the Nov. '80, and Jan. through April '81 issues of Ham Radio." Thats right, Steve! a stripline

If I start from the assumption regarding the input impedance 35 ohms in parallel with 92 pF, this is equivalent to 3.37-j11 in series form. If we calculate the 'L' adapter, it gives this Why would you

PIEL http://tonnesoftware.com/piel.html Sent: Friday, January 05, 2024 11:44 PM To: '[email protected]' Subject: RE: [ham-amplifiers] 144 mhz tuned input for a GG YC-156 ?? PIEL 73 N2LYM Sent:

PIEL 73 N2LYM Sent: Friday, January 05, 2024 11:21 PM To: [email protected] Subject: Re: [ham-amplifiers] 144 mhz tuned input for a GG YC-156 ?? Jim, is there public domain software program

Jim, is there public domain software program that helps with Pi network design? aka, I'm looking at 8877 50Mhz project in 2024 73 Robert W5AJ

What does the piece of Heliax do?

Try a 3/4 wavelength stripline. Get the design info from W6GGV's articles published in the Nov. '80, and Jan. through April '81 issues of Ham Radio. Steve, K0XP

A pi-circuit 73 Peter, DJ7WW -----Original-Nachricht----- Betreff: [ham-amplifiers] 144 mhz tuned input for a GG YC-156 ?? Datum: 2024-01-05T20:51:29+0100 Von: "Jim VE7RF" <jim.thom@...> An: