The original FT-897 CAT/Tuner control cable pins are 1-1, 2-2, etc
also the metal shield or metal ring on the connector has continuity
end to end.
73, Pat
KD1XX


--- In YaesuTuner@..., "Hanno Vogels" <dg8jz@t...> wrote:

Whow... thank you for the "bad" news just in time. Do you have your

original

cable still available? Can you check if the original cable is

straight? 1:1;

2:2 etc.

My cable... the short one... is installed.

Greetings

Hanno, DG8JZ in Munich

_____

Von: YaesuTuner@... [mailto:YaesuTuner@...]

Im

Auftrag von g3ybo
Gesendet: Freitag, 5. August 2005 00:10
An: YaesuTuner@...
Betreff: [YaesuTuner] Re: FC 40 controll cable


--- In YaesuTuner@..., "Hanno Vogels" <dg8jz@t...>

wrote:

Good Morning,
I have similar plan to do. Will buy such a spare cable and will

try

to

expand it with some other cables. I do not want to cut the

original

cable.

Will keep you informed as soon as I get the spare cable in

Germany

from a

Mac source.
vy 73
-----------------------------
Hanno Vogels, DG8JZ
eMail: Hanno@d...
WIRES. #7124D Echolink: #4904
phone: +49 8102 729600
fax: +49 8102 729655

<>
<>
<>



_____

Von: YaesuTuner@...

[mailto:YaesuTuner@...]

Im

Auftrag von happy_hamer2001
Gesendet: Mittwoch, 27. Juli 2005 20:16
An: YaesuTuner@...
Betreff: [YaesuTuner] Re: FC 40 controll cable


I am wondering the same information, I would like to buy an

extension

cable and then , how long can the cale be? I plan on mounting the

FC-

40 on my 60 foot tower and running a sloper wire.



--- In YaesuTuner@..., "dg8jz" <dg8jz@t...> wrote:

Dar friends,
I am using the FC40 with my 857 and 897 under several

circumstances.

In mobile I tested the FC 40 with 1 3m whip against the ATAS

120.

my

opinion is: Atas on 20-10m better, FC40 /whip combo on 40-80

better.

6m no chance of dx for a test.

my question: does anybody know a source for an additional

extender

cable for the remote control line? I do not want to cut the

original

cable.

Greetings from Munich

Hanno, DG8JZ

www.yaesu-museum.com
www.dg8jz.de

_____

YAHOO! GROUPS LINKS



* Visit your group "YaesuTuner
<> " on the web.


* To unsubscribe from this group, send an email to:
YaesuTuner-unsubscribe@...
<mailto:YaesuTuner-unsubscribe@...?

subject=Unsubscribe>

* Your use of Yahoo! Groups is subject to the Yahoo! Terms

of

Service

<> .


_____

I am told that a MAC cable will not work as the connections do
not go 1-1, 2-2, 3-3 so test before you plug it into the radio.

73s Roger G3YBO





_____

YAHOO! GROUPS LINKS



* Visit your group "YaesuTuner
<> " on the web.


* To unsubscribe from this group, send an email to:
YaesuTuner-unsubscribe@...
<mailto:YaesuTuner-unsubscribe@...?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of

Service

<> .


_____

I have checked the site and the cable is available at $8.99 for a 10ft
cable.............Roger

This eight-pin "Mini-DIN" control cable appears to be similar to the Apple
Macintosh serial printer cable for their ImageWriter printer but, like most
bi-directional printer cables, one or two wires are crossed (pins 6 and 8
for the Apple) making it useless, as I discovered, for the FC-40. However,
a Mini-DIN-8 extension cable (such as the ten foot male to female
"Cablestogo.com" No. 09569) works very nicely, since the wires and pins are
straight through. This kind of extension cord is becoming hard to find as
printer cables are now USB. So far, I have extended the control cable to a
total of 60 feet with no loss in performance. Yaesu claims that the tuner
box is waterproof but I place a thick white plastic bag over it when I'm
home as an added precaution.


This info I got off Eham.net on FT 897.
73s

Roger

开云体育

--- In YaesuTuner@..., "Hanno Vogels" <dg8jz@t...> wrote:

Good Morning,
I have similar plan to do. Will buy such a spare cable and will try

to

expand it with some other cables. I do not want to cut the original

cable.

Will keep you informed as soon as I get the spare cable in Germany

from a

Mac source.
vy 73
-----------------------------
Hanno Vogels, DG8JZ
eMail: Hanno@d...
WIRES. #7124D Echolink: #4904
phone: +49 8102 729600
fax: +49 8102 729655

<>
<>
<>



_____

Von: YaesuTuner@... [mailto:YaesuTuner@...]

Im

Auftrag von happy_hamer2001
Gesendet: Mittwoch, 27. Juli 2005 20:16
An: YaesuTuner@...
Betreff: [YaesuTuner] Re: FC 40 controll cable


I am wondering the same information, I would like to buy an

extension

cable and then , how long can the cale be? I plan on mounting the

FC-

40 on my 60 foot tower and running a sloper wire.



--- In YaesuTuner@..., "dg8jz" <dg8jz@t...> wrote:

Dar friends,
I am using the FC40 with my 857 and 897 under several

circumstances.

In mobile I tested the FC 40 with 1 3m whip against the ATAS 120.

my

opinion is: Atas on 20-10m better, FC40 /whip combo on 40-80

better.

6m no chance of dx for a test.

my question: does anybody know a source for an additional

extender

cable for the remote control line? I do not want to cut the

original

cable.

Greetings from Munich

Hanno, DG8JZ

www.yaesu-museum.com
www.dg8jz.de

_____

YAHOO! GROUPS LINKS



* Visit your group "YaesuTuner
<> " on the web.


* To unsubscribe from this group, send an email to:
YaesuTuner-unsubscribe@...
<mailto:YaesuTuner-unsubscribe@...?subject=Unsubscribe>


* Your use of Yahoo! Groups is subject to the Yahoo! Terms of

Service

<> .


_____

I am told that a MAC cable will not work as the connections do
not go 1-1, 2-2, 3-3 so test before you plug it into the radio.

73s Roger G3YBO

Any info on the use of the FC 40 withe a FT 897 and portable antennas.
I go away and find the antenna is always a problem in Hotels......Any
length of wire found to be good for 40 and 20m.......

开云体育

I am wondering the same information, I would like to buy an extension
cable and then , how long can the cale be? I plan on mounting the FC-
40 on my 60 foot tower and running a sloper wire.



--- In YaesuTuner@..., "dg8jz" wrote:
> Dar friends,
> I am using the FC40 with my 857 and 897 under several
circumstances.
> In mobile I tested the FC 40 with 1 3m whip against the ATAS 120.
my
> opinion is: Atas on 20-10m better, FC40 /whip combo on 40-80 better.
>
> 6m no chance of dx for a test.
>
> my question: does anybody know a source for an additional extender
> cable for the remote control line? I do not want to cut the
original
> cable.
>
> Greetings from Munich
>
> Hanno, DG8JZ
>
> www.yaesu-museum.com
> www.dg8jz.de

Hi all. Newbie here.
Just got the FT 857 and the ATAS 120 with a Comet CF530 Duplexer.
Just wondering if anyone had any experience with the ATAS 120?

It auto-tunes on most bands however a little difficult on 18mhz. All
other tune 100% 40m thru to 6m.

1st Question:
Is it possible to alter the whip length so as to work 80m?

2nd Question:
The ATAS is supposed to be fine on 2m and 70cm. However 2m is 100%
but high SWR on 70cm (SWR pops up on 857 screen)

Also the power reading on the screen for 2m is very low?

Any help and advice would be appreciated. Thanks

Tony de M0MTD

I am wondering the same information, I would like to buy an extension
cable and then , how long can the cale be? I plan on mounting the FC-
40 on my 60 foot tower and running a sloper wire.



--- In YaesuTuner@..., "dg8jz" <dg8jz@t...> wrote:

Dar friends,
I am using the FC40 with my 857 and 897 under several

circumstances.

In mobile I tested the FC 40 with 1 3m whip against the ATAS 120.

my

opinion is: Atas on 20-10m better, FC40 /whip combo on 40-80 better.

6m no chance of dx for a test.

my question: does anybody know a source for an additional extender
cable for the remote control line? I do not want to cut the

original

cable.

Greetings from Munich

Hanno, DG8JZ

www.yaesu-museum.com
www.dg8jz.de

Dar friends,
I am using the FC40 with my 857 and 897 under several circumstances.
In mobile I tested the FC 40 with 1 3m whip against the ATAS 120. my
opinion is: Atas on 20-10m better, FC40 /whip combo on 40-80 better.

6m no chance of dx for a test.

my question: does anybody know a source for an additional extender
cable for the remote control line? I do not want to cut the original
cable.

Greetings from Munich

Hanno, DG8JZ

www.yaesu-museum.com
www.dg8jz.de

Good morning,

I am going off to visit my parents in Alberta next month and
thinking of bringing my FT-857 and FC-40 with me. I am planning on
using one of the electric fences as an antenna. (The fence is not
energized, since no cattle are using this field) The fence is
approximately 300 m (1000 ft+) approximately 60 cm (2 ft) off the
ground and terminated to the ground at the far end. My question is if
this would be a viable antenna system? Is there anything I should look
out for?

73 de Greg
VE3DB

Chuck,
With a 102" whip, you get 6 meters through 40 meters.

You really want the wire from the tuner to the mount as short as possible, although it will work with just about any lenght. Just remember that the "antenna" starts at that connector on the tuner.

I have my FC-40 mounted in my aluminum toolbox. I have very little problems with tuning the 102" whip. It usually loads in about 3 to 5 seconds.

Hope this helps.

Thanks,

Mike, KB5OZE

I am thinking of buying a FC-40 for my pickup truck installation and
had a few questions.
1.Will the tuner with a 102" whip tune 10 to 80 meters?

2. How long a wire can be used to connect the tuner to the antenna mount?

I was thinking of mounting the tuner on the side of the tool box. It
would be about a foot from the tuner to the mount

Greg:

Don't use coax to connect your tuner to the antenna - the grounded
shield acts like a capacitor to ground and your tuner won't 'tuner'.

You need to make the wire from the lug to the whip as short as
possible - have you considered mounting the FC-40 outside the
vehicle?

You can use an 4:1 unun or an autotransformer in reverse- check out
K0BG's site at . I have used an
autotransformer on an powdered iron toroid core on my FC-40 to get
my 102" whip down to 60 meters, although I lost some S units on
recieve on higher bands.

Jay
W6SH



--- In YaesuTuner@..., "r0de_runr" <r0de_runr@y...>
wrote:

Hey all,

I sold my truck with the 102 inch whip....I had the fc-40 about 3
inchis away from the inside lug of the ball mount so it was

perfect

for 10 gauge wire from the fc-40 lugs to the ant.

Now I cannot drill into my (new) Olds Bravada, so I need to figure
another way.

Can I cut off the end of a 15ft coax, wire it to the tuner and
connect the other end to a pl259 mount for the whip, off the

bumper

sor something?

Didn't think I could use a coax.

Also, what if I used a 4:1 balun in reverse to accept the wires

from

the tuner and adapt them to the coax to make the run over to the
whip?

Can a balun be used in reverse? Could use it in my shack to

attach

attick mounted slinky to the tuner.

Greg
W0GAN
Just a dumb general.

Hey all,

I sold my truck with the 102 inch whip....I had the fc-40 about 3
inchis away from the inside lug of the ball mount so it was perfect
for 10 gauge wire from the fc-40 lugs to the ant.

Now I cannot drill into my (new) Olds Bravada, so I need to figure
another way.

Can I cut off the end of a 15ft coax, wire it to the tuner and
connect the other end to a pl259 mount for the whip, off the bumper
sor something?

Didn't think I could use a coax.

Also, what if I used a 4:1 balun in reverse to accept the wires from
the tuner and adapt them to the coax to make the run over to the
whip?

Can a balun be used in reverse? Could use it in my shack to attach
attick mounted slinky to the tuner.

Greg
W0GAN
Just a dumb general.

Greeting FC-40 users!

I have uploaded some pictures of the setup in my XYL's Jeep Wrangler
TJ in the folder "W6SH Jeep Wrangler TJ - FT-857D & FC-40".
Although my XYL would probably tolerate me putting the big ol' ball
mount over the rear fender for the whip - in the interests of
matrimonial harmony I decided to try for as much of a "bolt on"
installation for a FT-857D / FC-40 / 102" inch whip combo as I could
manage. It is a low-profile look and happily so far my XYL approves.

This setup is just what I ended up with and is probably not optimal -
but maybe someone will get some ideas for taking their own FC-40
mobile. Going HF mobile means making compromises - but I have been
pleased with the FC-40 since I got it last Christmas.

Some mobileer purists would argue for bugcatchers or screwdrivers,
but the whip has the advantage for a Jeep of being somewhat more
rugged when going off-road. I work downtown and the whip also is
easy to pull down to a tie down mounted over the driver's side of
the windshield when entering parking garages.

I have been pleased with the performance on 20 meters and higher
freqs. Tuning on 40 is sometimes hit or miss - the TJ doesn't have a
lot of sheet metal for a ground plane. Interestingly, 40 tunes up
better when the whip is pulled down. I am experimenting with an 1:4
toroid autotransformer and more grounding braids to see if 40 will
tune up better.

One issue I haven't had too much trouble with is RFI. TJs are
notorious for fuel pump noise, but I quieted mine down by placing
several clamp on ferrite beads on the fuel pump power lead as it
heads into the gas tank (this is a tight place to get into,
however). I also put ferrite beads on the taillight wires to keep
down fuel pump RFI - that seemed to help too. Be sure to ground the
tailpipe as it can radiate ignition noise too.

I still get some ignition noise at times despite having several
beads on the ignition wires, I have got some copper conductive
adhesive tape however and I will cover and ground those ignition
wires as suggested by K0BG (I highly recommend his site for
mobileers at www.k0bg.com).

The radio is mounted in the aftermarket metal "Insta-trunk" which
provides some theft protection. The FC-40, and whip are mounted on
a "Arizona Rocky Round" Jeep rear double antenna mount which is made
by Rick at arizonarockyroad.com . This mount uses the existing bolt
holes for the rear tire mount. The whip is a RadioShack 102" CB
whip. The whip insulator is Delrin and available at geotool.com .
Voltages at the tuner output can be very high so a good insulator is
required here.

The VHF antenna is a Comet SBB-7 foldover.

I used #10 dual wire from the battery posts - this is hidden along
the passenger side floor - both leads are fused. I had to replace
the 7 year old battery as it was weak and used a Optima yellow top
deep-cycle gel battery. I found a cheap 1 Farad car stereo capacitor
at a flea market and put in the trunk to on the power lead to ensure
there would be no voltage dips while transmitting - although this is
probably unnecessary, it looks good!

I used the existing brake light grommet in the tailgate to bring out
the HF coax lead, I did have to drill another 1/2" hole in the
tailgate to bring out the VHF coax and control lead.

I coiled the HF coax into several 6" turns before it entered the
tuner to reduce any coax radiation. The mounting plates that come
attached to the FC-40 were removed. The tuner is mounted to the back
of the Arizona Rockyroad mount using plumbers straps and stainless
self-tapping screws and grounded to the mount and tailgate with 1/2"
braid. The tailgate is also grounded to the body with 1/2" braid.
Conductive grease was used at all ground points.

So far I have been impressed with the FC-40, it performs as
advertised and seems pretty stable on the road. So far I have
worked North America and Europe, I have had S9 reports from W2 and
VE7 almost had a VK-land contact during a late band opening on 20m a
few nights ago, except he went QRT too soon.

I continue to try to improve the setup and I will add new pictures
if I think I have made any leaps forward.

73 de Jay
W6SH

I have used the LDG tuner before and it has a much larger span of
tuning. You can "make" the LDG tune a non resonant antenna easier
than with the Yaesu. The LDG Tuner is capable of a Antenna
impedance: 6 to 800 Ohms (Approximately up to 10:1 SWR)



where as the FC-30 can tune 17 to 150 Ohms (25 to 100 Ohms on 50 MHz)
The info was taken from the Yaesu 897D brochure



--- In YaesuTuner@..., "redhusky69" <MJKalik@A...> wrote:

--- I just bought a FT-897D- (still in the opened box) being brand
new to the Ham World since a novice license in 1967 - I also

bought

the FC-30 Tuner -(still in the sealed box) A ham from a large

radio

chain of stores suggested I not unseal the box and that I return

it

and exchange it for the LDG At-897 with the justification that

that

tuner will permit a larger band width. I would be very grateful if
anyone would provide me with whatever comments they might have
concerning this "advice" - Thank you for your reply - Mark - KC2OCY





In YaesuTuner@..., "Robbie Phelan" <robbiephelan@h...>
wrote:

Thanks Bill,

I came across this article on eham.. Might be of interest, it

was

written by

Paul KA6GEM....

""" The length of antenna wire is very important. The FC-40 will

tune 160

through 6 meters as Yaesu claims but it is entirely dependant on

the length

of the wire. Based on my findings, it will not tune a half-wave,

a

fairly

common limitation of "random wire" antenna tuners, and there

doesn't appear

to be a single length that is ideal for ALL bands, although 37

feet, in my

experience, comes pretty close. One nice thing is that it is

very

easy to

change your antenna length: just add or subtract a few feet and

that's it! I

have found that inserting a insulator at about 50 feet and

leaving

the ends

of the wires on each side stripped allows the option of simply

connecting

them or disconnecting them to work the 160 meter band or perhaps

the 60

meter band, etc.

I tried various lengths of wire from about 30 feet to about 130

feet, the

upper limit at my QTH. At 37 feet, I could tune up on almost

every

band but

the signal reports for the longer wavelength bands (80, 60, 40

etc.) were

marginal. As I increased the length of wire, I gained better

performance on

one band but lost on others. At about 85 feet, I received

excellent

reports

on 40 meters, but then I could not tune on the 80 meter band as

the

length

was too close to a half wave.

I ran a series of comparisons with two dipoles, one for 80

meters

and the

other for 40 meters. The 80 meter dipole performed better by one

or

two "S"

units than the FC-40 with a 65 foot quarter wave wire. I don't

have

enough

real estate to extend the wire to a three quarter wave or about

190

feet for

the 80 meter band.

On the 40 meter band, however, a length of about 90 feet

performed

very well

and the signal reports tended to be an "S" unit higher than the

40

meter

dipole. Although it's a vertically polarized antenna, I have not

noticed any

major increase in noise with the FC-40 random wire as compared

to a

dipole.

Unlike the Icom AH-4, the Yaesu FC-40 will tune on 160 meters

and I

made my

first contact on the top band in almost 15 years with a wire

about

85 feet

long. I had nothing to compare it to but the signal report I got

was

excellent.

Although still fairly new, I have heard two other FC-40s on the

air, mostly

in mobile set ups and both operators seemed very pleased with

their

performance. In summary, I'm very pleased with this new

automatic

antenna

tuner. I'd give the Yaesu FC-40 a solid "5" (on a 5 scale)

without

hesitation."""





----- Original Message -----
From: "kc9anq" <kc9anq@y...>
To: <YaesuTuner@...>
Sent: Wednesday, May 18, 2005 11:15 AM
Subject: [YaesuTuner] Re: FC-40

Robbie

Thank you for being the first post and welcome all to the new

group.

I have had the FC-40 for a month now and it work great I have
experimented with a 40 foot wire and a 55 foot wire with great

success,

It makes 60 meter in the USA a WALK IN THE PARK to use. I made

contacts

with great results on all bands but 160 and 6, I have not been

able to

tune up on 160 with such a short wire and 6 ,,,,,well 6 meter

is

just 6

meter LOL no conditions yet.

I am using the tuner with My 897D on field day and will be

using a

fulll wave loop for 160 meter. I will let the group know what

I

find by

next weekend. I plan on running a "test" with a loop before

field

day.

Thanks for joining,

Bill




--- In YaesuTuner@..., "ei2ip" <robbiephelan@h...>

wrote:

I just purchased a FC-40 from Ebay... Should have it next

week..

What is the general feeling about this tuner, does it

perform

well??

Robbie,
EI2IP

--- I just bought a FT-897D- (still in the opened box) being brand
new to the Ham World since a novice license in 1967 - I also bought
the FC-30 Tuner -(still in the sealed box) A ham from a large radio
chain of stores suggested I not unseal the box and that I return it
and exchange it for the LDG At-897 with the justification that that
tuner will permit a larger band width. I would be very grateful if
anyone would provide me with whatever comments they might have
concerning this "advice" - Thank you for your reply - Mark - KC2OCY





In YaesuTuner@..., "Robbie Phelan" <robbiephelan@h...>
wrote:

Thanks Bill,

I came across this article on eham.. Might be of interest, it was

written by

Paul KA6GEM....

""" The length of antenna wire is very important. The FC-40 will

tune 160

through 6 meters as Yaesu claims but it is entirely dependant on

the length

of the wire. Based on my findings, it will not tune a half-wave, a

fairly

common limitation of "random wire" antenna tuners, and there

doesn't appear

to be a single length that is ideal for ALL bands, although 37

feet, in my

experience, comes pretty close. One nice thing is that it is very

easy to

change your antenna length: just add or subtract a few feet and

that's it! I

have found that inserting a insulator at about 50 feet and leaving

the ends

of the wires on each side stripped allows the option of simply

connecting

them or disconnecting them to work the 160 meter band or perhaps

the 60

meter band, etc.

I tried various lengths of wire from about 30 feet to about 130

feet, the

upper limit at my QTH. At 37 feet, I could tune up on almost every

band but

the signal reports for the longer wavelength bands (80, 60, 40

etc.) were

marginal. As I increased the length of wire, I gained better

performance on

one band but lost on others. At about 85 feet, I received excellent

reports

on 40 meters, but then I could not tune on the 80 meter band as the

length

was too close to a half wave.

I ran a series of comparisons with two dipoles, one for 80 meters

and the

other for 40 meters. The 80 meter dipole performed better by one or

two "S"

units than the FC-40 with a 65 foot quarter wave wire. I don't have

enough

real estate to extend the wire to a three quarter wave or about 190

feet for

the 80 meter band.

On the 40 meter band, however, a length of about 90 feet performed

very well

and the signal reports tended to be an "S" unit higher than the 40

meter

dipole. Although it's a vertically polarized antenna, I have not

noticed any

major increase in noise with the FC-40 random wire as compared to a

dipole.

Unlike the Icom AH-4, the Yaesu FC-40 will tune on 160 meters and I

made my

first contact on the top band in almost 15 years with a wire about

85 feet

long. I had nothing to compare it to but the signal report I got was
excellent.

Although still fairly new, I have heard two other FC-40s on the

air, mostly

in mobile set ups and both operators seemed very pleased with their
performance. In summary, I'm very pleased with this new automatic

antenna

tuner. I'd give the Yaesu FC-40 a solid "5" (on a 5 scale) without
hesitation."""





----- Original Message -----
From: "kc9anq" <kc9anq@y...>
To: <YaesuTuner@...>
Sent: Wednesday, May 18, 2005 11:15 AM
Subject: [YaesuTuner] Re: FC-40

Robbie

Thank you for being the first post and welcome all to the new

group.

I have had the FC-40 for a month now and it work great I have
experimented with a 40 foot wire and a 55 foot wire with great

success,

It makes 60 meter in the USA a WALK IN THE PARK to use. I made

contacts

with great results on all bands but 160 and 6, I have not been

able to

tune up on 160 with such a short wire and 6 ,,,,,well 6 meter is

just 6

meter LOL no conditions yet.

I am using the tuner with My 897D on field day and will be using a
fulll wave loop for 160 meter. I will let the group know what I

find by

next weekend. I plan on running a "test" with a loop before field

day.

Thanks for joining,

Bill




--- In YaesuTuner@..., "ei2ip" <robbiephelan@h...>

wrote:

I just purchased a FC-40 from Ebay... Should have it next week..

What is the general feeling about this tuner, does it perform

well??

Robbie,
EI2IP

Hi,

Looking for some opinions on operating a FT-857 with the FC-40 dockside portable. After reading the June issue of QST and reading 'A Portable Inverted V Antenna' article, I am thinking of modifying it. My plans are to change the antenna from the inverted V to a loop and then use the water for the ground. My other choice may be to use the triadic on the sailboat, but since I plan to operate on the dock, I am worried about the stress which would be placed on the patch cables to the rig. Also by using the loop it would also allow for more portable operations in the future. Any help would be appreciated.

73 de Greg
VE3DB

Well, right now I am using a standard 102" whip. I am still in a testing phase. I have had some problems using a coupler in the Dakota. With the current setup though, the FC-40/FT-857 was receiving almost as good as my FT-847 on a 60' long wire with a SGC-230. I have a Houston trip (driving) coming up and hopefully will have more information during and after that. I am thinking of replacing the 102" whip with something a little longer, maybe in the 12' range. I will definitely update everyone on how it goes.

Thanks,

Mike









Date: Wed, 18 May 2005 21:01:00 -0000
From: "kc9anq" <kc9anq@...>
Subject: Re: FC-40 mobile installation

Nice install Mike,

Are you using a regular 102 inch whip? What kind of luck are you
having?



--- In YaesuTuner@..., "kb5oze" <mike@d...> wrote:

I have uploaded some pictures that show my mobile installation. Feel
free to e-mail me with any questions.

Thanks,

Mike, KB5OZE

________________________________________________________________________
________________________________________________________________________



------------------------------------------------------------------------
Yahoo! Groups Links




------------------------------------------------------------------------