开云体育

Well said Bruno. 73 de Ian VK6CR

Hi Greg, With all respect, a healthy approach on these kind of problems should be “what am I doing wrong” instead of blaming the FT847 to fail, to be dumb or to pretend it wants to be smart. In

Yep, that's pretty much what I wanted to do as well, but driven from a Raspberry Pi 4B. Got it all wired up, and it failed miserably. The problem? No transmit audio. Bottom line is that the 847

Greetings. I know it probably has been discussed an unknown number of times previously, but I want to start using my 847 in the digital modes, both on HF as well as 6M + VHF/UHF. I want the members

Hi, I made a simple Eurocard prototype pcb to be able to use an FT817/857/897 CW filter in the FT847. The file is added to the files/mod directory.

Thanks Micky, I also added a mod to add AGC_OFF functionality via the MOX button on the front panel. 73, Bruno Op ma 20 dec. 2021 om 00:49 schreef Micky Corrow <opus@...>:

Hi, I added a mod to the Files MOD folder to add the AGC_OFF functionality without destroying your transceiver.

The following files have been uploaded to the Files area of the [email protected] group. * /FT-847 Mods/TCXO_9 mod FT847 ON6AB.pdf ( /g/YaesuFT847/files/FT-847 Mods/TCXO_9 mod

Hi Bruno Please retry your mod upload, tag it and send it again to the files section. Micky K1XH

Good morning Everyone. As the primary owner of this groupe, I have one moderator and a part time owner who is in concurance with me.? We need someone to become a full partner with us, this is in case

Hi, I did the TCXO-9 mod on my FT847 but a little differently (and easier) as to what's already on the internet. It is performing fine and I did not find any unwanted side effects. If you're

Hi Andy, Interesting... I tested my FT847 (with TCXO-9 mod) on FM today but I can't find any tones as you describe. I did the TCXO-9 mod a bit different as to what is available on the internet and I

I tried the TCXO 9 mod, and even though it improved stability, on 2 metres FM it generated an awful tone for some reason. Output was clean, and no amount of decoupling would cure it. So I used a bit

Hello Yvan, Indeed, putting foam over the quartz is a far better solution. Looking at the foam that is over the crystals in my 2004 unit, I suspect it was done at the factory. Meanwhile I improved the

Hello, I see one modif for FT847 for better stability, it is simply to put isolation of foam or plastic on quartz. I never have the stability?problem with my 847, who I use for monitoring some sats.

I tried the QH40A crystal heater mod as presented all over the internet. However, it did not work out for me ( my FT847 is a 2004 model). I can't quite figure out how it is possible that for some

In message <a12210a3-bdb4-4c00-5da4-23e9fe78920e@...>, Alan G3WXI aka G8AGQ <strongmra@...> writes

Good Evening Brian Brian Howie GM4DIJ wrote: I too am a long time 847 owner, having bought mine used around the change of the century from an old timer in ill health (as I am now) and I am writing to

Hi Folks, On August 5, 2021 message #214 I had written the following message: "I am having a problem originating a message. Before I waste anyone's I would like to ask the following question of the

Ok folks, I have no idea what happened but after a reset I'm back in the group. No need for action boss. Leighton. GW3FSP.