开云体育

If I use the YD8116 to switch my MP5 points, will the switch notify iTrains? Secondly, if I use a physical momentary push button switch on the layouts mimic panel to activate the MP5 driven point,

Hi, No, the YD8xxx decoders are one-way. for having position feedback from your MP’s contacts, we advise our YD6016xx-GND feedback modules.

Hi All, I am currently using Diigtrax hardware, but as I get deeper into this area I am considering changing direction - with YaMoRC being a lead contender. My question is how much of my current

Just did the conversion #DR5000 to #YD7001. All good, except when I connect my Windows Laptop via WiFi to YD7001-D00#####-AP I have a connection but no Internet connection. The YD7001 is connected to

Hi David. This is a new forum...not too active yet.? But it will be. Try Digikeijs Forum.?I'm unable to comment on Digitrax. My understanding is that You can use a MAC and a web browser to

Does anyone know if a DR5000 upgraded to a YD9401 will work with Digitrax Simplex throttles? My DR5000 will, with some settings tweaks. Alex -- Alexander Wood Hartford-New Haven, CT Modeling the

Hi Alex, The YD9401 does not / can not / may not implement the closed and proprietary DigiTrax Tether less protocol. So, sorry, won't work. You'll still u need one of those UR9x devices. Greets, Karst

Yep, sorry, it's an ongoing process to refine the manuals. That's one of the most difficult parts of the whole process. And here now as well :) For some Answers: It is similar, has some other nice

Hi, Gatewaying nor bridging is provided in the YD9401. Reason: Security and Perfomance related. It was THE big security hole in DR5000's RM-04 module. We closed that hole on purpose. Greets, Karst

Karst, I think you misunderstood my question. Of course a UR91 is required to receive the RF signals from a UT4R, DT400R or other Simplex throttle. My question is whether Digitrax Simplex throttles

Ah, In that way :) Do you mean the Baudrate-Tune option ? That one I implemented already back in V1.4.2.... And I did it again in the YD7100 Firmware ( ported ==> YD7001 ) because not only UR91 suffer

Karst, That sounds promising! The Baud Rate setting Ryan had me change on the DR5000 is LocoNet tab>Settings and I set the Baud Rate to 800, then the Simplex throttles worked fine. The change was

> > > > Hello > This is my first post to this group. I am hoping to learn more about some > of the features on the YD7001. ?I have just upgraded my DR5000 to a YD7001 > which was very easy and

Hi Les, Welcome here as well :) Unfortunately I do not have sufficient knowledge about the workings of TC's Smarthand What I *can* tell you is that the YD9401 Module does not bridge traffic from WiFi

Do you mean this setting ? We have it in YD7100/YD7001 in the new "Expert" tab ;) Greets, Karst

Les, What specific functionality are you looking for? An ESU ECoS with TC Gold is a pretty substantial setup. You'd still need a network for +SmartHand, the Wi-Fi on the YD7001 would be WiThrottle or

Karst, I think that's the same setting as in the Digikeijs software. If that's the case, then it should work to enable reception of LocoNet packets from the UR91. Alex -- Alexander Wood Hartford-New

Hello Les Waters By saying "I have just upgraded my DR5000 to a YD7001 which was very easy and straightforward.", do you mean that you loaded the YD7001 firmware on the DR5000? Many thanks. PaulXpress

PaulXpress There was a bit more to it than that. ?You first have to replace the exiting DR5000 daughterboard. ?I purchased a YD9401 daughter board from DCCTrainAutomation in the UK. Carefully read

Alex i have had an ECoS for 15 years now. ?Originally I had a black and white one (50000) and then a couple of years later I upgraded to a colour screen version (52000). ?So it is quite old now.