SDTVer66.9 results
开云体育After totally scrubbing and rebuilding the IDE and libraries, I can compile and run everything again. However Ver66.4 and 66.9 only run at 600MHz if TCXO is defined. They both freeze if compiled with 528MHz. The Receive I&Q Cal worked quite well, except the button
assignments don't agree with the directions. Compiled with: Faster with LTO, 600 MHz, Dual Serial SDTVer66.4
--
73
Bob W3RDL |
||
开云体育Any oscillations on 10M or 6M? ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? From: [email protected] <[email protected]> On Behalf Of Robert Luken W3RDL via groups.io
Sent: Sunday, March 23, 2025 10:51 PM To: [email protected] Subject: [SoftwareControlledHamRadio] SDTVer66.9 results ? After totally scrubbing and rebuilding the IDE and libraries, I can compile and run everything again. However Ver66.4 and 66.9 only run at 600MHz if TCXO is defined. They both freeze if compiled with 528MHz. The Receive I&Q Cal worked quite well, except the button assignments don't agree with the directions. Compiled with: Faster with LTO, 600 MHz, Dual Serial SDTVer66.4 -- 73 Bob W3RDL ?
|
||
开云体育Bill, I don't have any oscillations, but then I don't have a LPF or PA built yet. I lost over a week trying to get back to where I could compile a running version.? I attached the spectrum of the 10m & 6m outputs from the RF
board. The output on 6m is down significantly. On 3/24/2025 12:08 AM, K9HZ via
groups.io wrote:
--
73
Bob W3RDL |
||
开云体育Ok good to this point. ?Dr.?William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton - J68HZ Soufriere, St. Lucia W.I. Rent it: www.VillaGrandPiton.com email:??bill@... ? On Mar 25, 2025, at 5:51?PM, Robert Luken W3RDL via groups.io <now.w3rdl@...> wrote:
|
||
开云体育What is coming out of the QSE after the BPF?? The PA will amplify pretty much everything from 1-150 MHz (at different gains).? If the input is not clean, the output won’t be that clean. ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois ? Owner – Operator Villa Grand Piton – J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? From: [email protected] <[email protected]> On Behalf Of Robert Luken W3RDL via groups.io
Sent: Tuesday, March 25, 2025 4:51 PM To: [email protected] Subject: Re: [SoftwareControlledHamRadio] SDTVer66.9 results ? Bill, I don't have any oscillations, but then I don't have a LPF or PA built yet. I lost over a week trying to get back to where I could compile a running version.? I attached the spectrum of the 10m & 6m outputs from the RF board. The output on 6m is down significantly. On 3/24/2025 12:08 AM, K9HZ via groups.io wrote:
-- 73 Bob W3RDL |
K9HZ
