|
Re: No SSB output
It's not real clear where to connect the I and Q outputs (line out left and right) on the Audio Adapter.? Referring to the back side of the Audio adapter:
?
Where it says
LINE OUT To the right this are three vias, with L G R underneath them. That is left channel, ground, and right channel line out.? "Line out" is an audio term, but we are calling it I and Q channels. It is good that the ground is in the middle, because you can easily flip the connector if you end up with I and Q channels reversed.
Another thing about the audio adapter is that it was not involved with the receiver in the original T41.? I'm not sure about V12. T41EEE.9 uses the Audio Adapter's headphone output for receiver audio, but that is its only involvement in the receiver. Also interesting is that there is a 2nd audio adapter device instantiated in the code and it has associated commands.? These commands do nothing.
?
--
73 Greg KF5N |
|
Re: No SSB output
¿ªÔÆÌåÓýThis bit right here¡. Make sire it works before moving on¡ ? ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois ? Owner ¨C Operator Villa Grand Piton ¨C J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? From: [email protected] <[email protected]> On Behalf Of Tim via groups.io
Sent: Thursday, April 17, 2025 6:49 AM To: [email protected] Subject: Re: [SoftwareControlledHamRadio] No SSB output ? PTT working, it goes into TX and amps increase, relays click. I2C checked out on all but BPF which I am using 3rd party BCD to control. Audio hat works fine for RX. Tim? ? |
|
Re: No SSB output
¿ªÔÆÌåÓýTim, ? Oliver is correct¡ if the audio hat + software is working¡ you should see a audio-like waveform on J17¡ which is the generated I/Q output to the RF board.? You can trace that back to PINS 1 and 2 (I and Q) on the hat.? If you don¡¯t see anything there to ground (and its about 0-200 mv), no sense going down stream to the RF, BPF, LPF etc. until that works. ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois ? Owner ¨C Operator Villa Grand Piton ¨C J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? From: [email protected] <[email protected]> On Behalf Of Tim via groups.io
Sent: Thursday, April 17, 2025 6:49 AM To: [email protected] Subject: Re: [SoftwareControlledHamRadio] No SSB output ? PTT working, it goes into TX and amps increase, relays click. I2C checked out on all but BPF which I am using 3rd party BCD to control. Audio hat works fine for RX. Tim? ? |
|
Re: New book
Thanks, John! Jack, W8TEE
On Thursday, April 17, 2025 at 06:17:45 AM EDT, John Owens K1JO via groups.io <johnowenschina@...> wrote:
Thanks Jack. The automated message from Amazon told me to keep the old book and they would send a new one :)...I wonder if they will send a new Old one.
When the New new one arrives, I will write a nice review. Thanks for the great work!
John K1JO
-- Jack, W8TEE |
|
Re: Just curious. . .
¿ªÔÆÌåÓýYou gain some slow memory to store stuff in¡ ? ? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ ? Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois ? Owner ¨C Operator Villa Grand Piton ¨C J68HZ Soufriere, St. Lucia W.I. Rent it: ? Moderator: North American QRO Group at Groups.IO. Moderator: Amateur Radio Builders Group at Groups.IO. ? email:? bill@... ? ? From: [email protected] <[email protected]> On Behalf Of Duane B via groups.io
Sent: Wednesday, April 16, 2025 10:45 PM To: [email protected] Subject: [SoftwareControlledHamRadio] Just curious. . . ? But do you gain anything by populating 1 or 2 of the 8Mb SPI memory chips on the Teensy?? Or do you loose? some functionality by doing that? ? Just curious. ? Thanks, Duane - K5CA |
|
Re: New book
Yeah, I did too, but twice received the wrong book. I have redone the submission from scratch and I should be hearing within 72 hours. It will have a new ISBN number, which means we lose all of the nice reviews we had up until now. To all those who took the time to say nice things about the book, a huge Thank You from Al and I. I will post when the new book is ready to ship. Meanwhile, they have been good about taking books back. Jack, W8TEE
On Wednesday, April 16, 2025 at 09:14:16 PM EDT, John Owens K1JO via groups.io <johnowenschina@...> wrote:
I just received the wrong one, the old one that I already have :(
Strange, as I waited until the purchase page had the new cover with the black T-41.
John K1JO
-- Jack, W8TEE |
|
Re: New book
Oddly, two people have written that they received the right book. Even harder to figure out now. I just went through the entire process again and updated everything, including the ad narrative (which has 4SQRP still selling a kit). I should get word back within 72 hours that all is well. The bad news is that about 165 very good book reviews will no longer be tied to the book...it starts over. Jack, W8TEE
On Wednesday, April 16, 2025 at 01:38:14 PM EDT, Greg KF5N via groups.io <greg.electricity@...> wrote:
Amazon needs to be hammered on again.? They are not getting it done correctly.
?
--
73 Greg KF5N
-- Jack, W8TEE |
|
Re: New book
Glad to hear it...thanks! Jack, W8TEE
On Wednesday, April 16, 2025 at 02:44:53 PM EDT, Duane B via groups.io <dbrantley@...> wrote:
I did, finally, receive a copy of the NEW book.? Received it last week.? I meant to post up about it but had a senior moment and forgot too.? Amazon even told me to keep the old copy.
?
Duane - K5CA
-- Jack, W8TEE |
K9HZ
jjpurdum
John Owens K1JO